说明
检查是否存在 UDP 数据包,并报告大小。 parsePacket() 必须在使用 UDP 读取缓冲区之前调用。read()。
用法
EthernetUDP.parsePacket();
参数
None
返回
- int:接收到的UDP数据包的大小
示例
#include <SPI.h> // needed for Arduino versions later than 0018
#include <Ethernet.h>
#include <EthernetUdp.h> // UDP library from: bjoern@cs.stanford.edu 12/30/2008
// Enter a MAC address and IP address for your controller below.
// The IP address will be dependent on your local network:
byte mac[] = {
0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };
IPAddress ip(192, 168, 1, 177);
unsigned int localPort = 8888; // local port to listen on
// An EthernetUDP instance to let us send and receive packets over UDP
EthernetUDP Udp;
void setup() {
// start the Ethernet and UDP:
Ethernet.begin(mac,ip);
Udp.begin(localPort);
Serial.begin(9600);
}
void loop() {
// if there's data available, read a packet
int packetSize = Udp.parsePacket();
if(packetSize)
{
Serial.print("Received packet of size ");
Serial.println(packetSize);
}
delay(10);
}
相关用法
- Arduino Ethernet - EthernetUDP.beginPacket()用法及代码示例
- Arduino Ethernet - EthernetUDP.available()用法及代码示例
- Arduino Ethernet - EthernetUDP.read()用法及代码示例
- Arduino Ethernet - EthernetUDP.endPacket()用法及代码示例
- Arduino Ethernet - EthernetUDP.begin()用法及代码示例
- Arduino Ethernet - EthernetUDP.write()用法及代码示例
- Arduino Ethernet - Ethernet.setRetransmissionTimeout()用法及代码示例
- Arduino Ethernet - Ethernet.MACAddress()用法及代码示例
- Arduino Ethernet - Ethernet.hardwareStatus()用法及代码示例
- Arduino Ethernet - Ethernet.localIP()用法及代码示例
- Arduino Ethernet - Ethernet.setDnsServerIP()用法及代码示例
- Arduino Ethernet - Ethernet.init()用法及代码示例
- Arduino Ethernet - Ethernet.setMACAddress()用法及代码示例
- Arduino Ethernet - EthernetServer()用法及代码示例
- Arduino Ethernet - Ethernet.setSubnetMask()用法及代码示例
- Arduino Ethernet - Ethernet.dnsServerIP()用法及代码示例
- Arduino Ethernet - Ethernet.setLocalIP()用法及代码示例
- Arduino Ethernet - Ethernet.gatewayIP()用法及代码示例
- Arduino Ethernet - Ethernet.setGatewayIP()用法及代码示例
- Arduino Ethernet - EthernetClient()用法及代码示例
- Arduino Ethernet - Ethernet.setRetransmissionCount()用法及代码示例
- Arduino Ethernet - Ethernet.linkStatus()用法及代码示例
- Arduino Ethernet - Ethernet.begin()用法及代码示例
- Arduino Ethernet - Ethernet.subnetMask()用法及代码示例
- Arduino Ethernet - server.begin()用法及代码示例
注:本文由纯净天空筛选整理自arduino.cc大神的英文原创作品 Ethernet - EthernetUDP.parsePacket()。非经特殊声明,原始代码版权归原作者所有,本译文未经允许或授权,请勿转载或复制。