C++ ZONE_SETTINGS::SetCornerSmoothingType方法代码示例

bool DIALOG_NON_COPPER_ZONES_EDITOR::TransferDataFromWindow()
{
    m_settings.SetCornerSmoothingType( m_cornerSmoothingChoice->GetSelection() );

    m_settings.SetCornerRadius( m_settings.GetCornerSmoothingType() == ZONE_SETTINGS::SMOOTHING_NONE
                                ? 0 : m_cornerRadius.GetValue() );

    if( !m_gridStyleRotation.Validate( -1800, 1800 ) )
        return false;

    m_settings.m_ZoneMinThickness = m_minWidth.GetValue();

    switch( m_OutlineAppearanceCtrl->GetSelection() )
    {
    case 0: m_settings.m_Zone_HatchingStyle = ZONE_CONTAINER::NO_HATCH;      break;
    case 1: m_settings.m_Zone_HatchingStyle = ZONE_CONTAINER::DIAGONAL_EDGE; break;
    case 2: m_settings.m_Zone_HatchingStyle = ZONE_CONTAINER::DIAGONAL_FULL; break;
    }

    if( m_GridStyleCtrl->GetSelection() > 0 )
        m_settings.m_FillMode = ZFM_HATCH_PATTERN;
    else
        m_settings.m_FillMode = ZFM_POLYGONS;


    if( m_settings.m_FillMode == ZFM_HATCH_PATTERN )
    {
        int minThickness = m_minWidth.GetValue();

        if( !m_gridStyleThickness.Validate( minThickness, INT_MAX ) )
            return false;

        if( !m_gridStyleGap.Validate( minThickness, INT_MAX ) )
            return false;
    }


    m_settings.m_HatchFillTypeOrientation = m_gridStyleRotation.GetValue()/10.0; // value is returned in deci-degree
    m_settings.m_HatchFillTypeThickness = m_gridStyleThickness.GetValue();
    m_settings.m_HatchFillTypeGap = m_gridStyleGap.GetValue();
    m_settings.m_HatchFillTypeSmoothingLevel = m_spinCtrlSmoothLevel->GetValue();
    m_settings.m_HatchFillTypeSmoothingValue = m_spinCtrlSmoothValue->GetValue();

    wxConfigBase* cfg = Kiface().KifaceSettings();
    wxASSERT( cfg );

    cfg->Write( ZONE_NET_OUTLINES_STYLE_KEY, (long) m_settings.m_Zone_HatchingStyle );

    m_settings.m_Zone_45_Only = m_ConstrainOpt->GetValue();

    // Get the layer selection for this zone
    int layer = -1;
    for( int ii = 0; ii < m_layers->GetItemCount(); ++ii )
    {
        if( m_layers->GetToggleValue( (unsigned) ii, 0 ) )
        {
            layer = ii;
            break;
        }
    }

    if( layer < 0 )
    {
        DisplayError( this, _( "No layer selected." ) );
        return false;
    }

    *m_ptr = m_settings;
    return true;
}

bool DIALOG_COPPER_ZONE::AcceptOptions( bool aPromptForErrors, bool aUseExportableSetupOnly )
{
    switch( m_PadInZoneOpt->GetSelection() )
    {
    case 3:
        // Pads are not covered
        m_settings.SetPadConnection( PAD_NOT_IN_ZONE );
        break;

    case 2:
        // Use thermal relief for THT pads
        m_settings.SetPadConnection( THT_THERMAL );
        break;

    case 1:
        // Use thermal relief for pads
        m_settings.SetPadConnection( THERMAL_PAD );
        break;

    case 0:
        // pads are covered by copper
        m_settings.SetPadConnection( PAD_IN_ZONE );
        break;
    }

    switch( m_OutlineAppearanceCtrl->GetSelection() )
    {
    case 0:
        m_settings.m_Zone_HatchingStyle = CPolyLine::NO_HATCH;
        break;

    case 1:
        m_settings.m_Zone_HatchingStyle = CPolyLine::DIAGONAL_EDGE;
        break;

    case 2:
        m_settings.m_Zone_HatchingStyle = CPolyLine::DIAGONAL_FULL;
        break;
    }

    m_settings.m_ArcToSegmentsCount = m_ArcApproximationOpt->GetSelection() == 1 ?
                                           ARC_APPROX_SEGMENTS_COUNT_HIGHT_DEF :
                                           ARC_APPROX_SEGMENTS_COUNT_LOW_DEF;

    if( m_Config )
    {
        m_Config->Write( ZONE_NET_OUTLINES_HATCH_OPTION_KEY,
                         (long) m_settings.m_Zone_HatchingStyle );
        wxString filter = m_DoNotShowNetNameFilter->GetValue();
        m_Config->Write( ZONE_NET_FILTER_STRING_KEY, filter );
    }

    m_netNameShowFilter = m_ShowNetNameFilter->GetValue();
    m_settings.m_FillMode = (m_FillModeCtrl->GetSelection() == 0) ? 0 : 1;

    wxString txtvalue = m_ZoneClearanceCtrl->GetValue();
    m_settings.m_ZoneClearance = ReturnValueFromString( g_UserUnit, txtvalue );

    // Test if this is a reasonable value for this parameter
    // A too large value can hang Pcbnew
    #define CLEARANCE_MAX_VALUE ZONE_CLEARANCE_MAX_VALUE_MIL*IU_PER_MILS
    if( m_settings.m_ZoneClearance > CLEARANCE_MAX_VALUE )
    {
        wxString msg;
        msg.Printf( _( "Clearance must be smaller than %f\" / %f mm." ),
            ZONE_CLEARANCE_MAX_VALUE_MIL / 1000.0, ZONE_CLEARANCE_MAX_VALUE_MIL * 0.0254 );
        DisplayError( this, msg );
        return false;
    }

    txtvalue = m_ZoneMinThicknessCtrl->GetValue();
    m_settings.m_ZoneMinThickness = ReturnValueFromString( g_UserUnit, txtvalue );

    if( m_settings.m_ZoneMinThickness < (ZONE_THICKNESS_MIN_VALUE_MIL*IU_PER_MILS) )
    {
        wxString msg;
        msg.Printf( _( "Minimum width must be larger than %f\" / %f mm." ),
            ZONE_THICKNESS_MIN_VALUE_MIL / 1000.0, ZONE_THICKNESS_MIN_VALUE_MIL * 0.0254 );
        DisplayError( this, msg );
        return false;
    }

    m_settings.SetCornerSmoothingType( m_cornerSmoothingChoice->GetSelection() );
    txtvalue = m_cornerSmoothingCtrl->GetValue();
    m_settings.SetCornerRadius( ReturnValueFromString( g_UserUnit, txtvalue ) );

    m_settings.m_ZonePriority = m_PriorityLevelCtrl->GetValue();

    if( m_OrientEdgesOpt->GetSelection() == 0 )
        m_settings.m_Zone_45_Only = false;
    else
        m_settings.m_Zone_45_Only = true;

    m_settings.m_ThermalReliefGap = ReturnValueFromTextCtrl( *m_AntipadSizeValue );
    m_settings.m_ThermalReliefCopperBridge = ReturnValueFromTextCtrl( *m_CopperWidthValue );

    if( m_Config )
    {
        ConfigBaseWriteDouble( m_Config, ZONE_CLEARANCE_WIDTH_STRING_KEY,
                               (double) m_settings.m_ZoneClearance / IU_PER_MILS );
//.........这里部分代码省略.........

int PCB_EDIT_FRAME::Begin_Zone( wxDC* DC )
{
    ZONE_SETTINGS zoneInfo = GetZoneSettings();

    // verify if s_CurrentZone exists (could be deleted since last selection) :
    int ii;
    for( ii = 0; ii < GetBoard()->GetAreaCount(); ii++ )
    {
        if( s_CurrentZone == GetBoard()->GetArea( ii ) )
            break;
    }

    if( ii >= GetBoard()->GetAreaCount() ) // Not found: could be deleted since last selection
    {
        s_AddCutoutToCurrentZone = false;
        s_CurrentZone = NULL;
    }

    ZONE_CONTAINER* zone = GetBoard()->m_CurrentZoneContour;

    // Verify if a new zone is allowed on this layer:
    if( zone == NULL  )
    {
        if( GetToolId() == ID_PCB_KEEPOUT_AREA_BUTT && !IsCopperLayer( GetActiveLayer() ) )
        {
            DisplayError( this,
                          _( "Error: a keepout area is allowed only on copper layers" ) );
            return 0;
        }
    }

    // If no zone contour in progress, a new zone is being created,
    if( zone == NULL )
    {
        zone = GetBoard()->m_CurrentZoneContour = new ZONE_CONTAINER( GetBoard() );
        zone->SetFlags( IS_NEW );
        zone->SetTimeStamp( GetNewTimeStamp() );
    }

    if( zone->GetNumCorners() == 0 )    // Start a new contour: init zone params (net, layer ...)
    {
        if( !s_CurrentZone )            // A new outline is created, from scratch
        {
            ZONE_EDIT_T edited;

            // Init zone params to reasonable values
            zone->SetLayer( GetActiveLayer() );

            // Prompt user for parameters:
            m_canvas->SetIgnoreMouseEvents( true );

            if( zone->IsOnCopperLayer() )
            {
                // Put a zone on a copper layer
                if( GetBoard()->GetHighLightNetCode() > 0 )
                {
                    zoneInfo.m_NetcodeSelection = GetBoard()->GetHighLightNetCode();
                    zone->SetNetCode( zoneInfo.m_NetcodeSelection );
                }

                double tmp = ZONE_THERMAL_RELIEF_GAP_MIL;

                wxConfigBase* cfg = Kiface().KifaceSettings();
                cfg->Read( ZONE_THERMAL_RELIEF_GAP_STRING_KEY, &tmp );
                zoneInfo.m_ThermalReliefGap = KiROUND( tmp * IU_PER_MILS);

                tmp = ZONE_THERMAL_RELIEF_COPPER_WIDTH_MIL;
                cfg->Read( ZONE_THERMAL_RELIEF_COPPER_WIDTH_STRING_KEY, &tmp );
                zoneInfo.m_ThermalReliefCopperBridge = KiROUND( tmp * IU_PER_MILS );

                tmp = ZONE_CLEARANCE_MIL;
                cfg->Read( ZONE_CLEARANCE_WIDTH_STRING_KEY, &tmp );
                zoneInfo.m_ZoneClearance = KiROUND( tmp * IU_PER_MILS );

                tmp = ZONE_THICKNESS_MIL;
                cfg->Read( ZONE_MIN_THICKNESS_WIDTH_STRING_KEY, &tmp );
                zoneInfo.m_ZoneMinThickness = KiROUND( tmp * IU_PER_MILS );

                zoneInfo.m_CurrentZone_Layer = zone->GetLayer();

                if( GetToolId() == ID_PCB_KEEPOUT_AREA_BUTT )
                {
                    zoneInfo.SetIsKeepout( true );
                    // Netcode, netname and some other settings are irrelevant,
                    // so ensure they are cleared
                    zone->SetNetCode( NETINFO_LIST::UNCONNECTED );
                    zoneInfo.SetCornerSmoothingType( ZONE_SETTINGS::SMOOTHING_NONE );
                    zoneInfo.SetCornerRadius( 0 );

                    edited = InvokeKeepoutAreaEditor( this, &zoneInfo );
                }
                else
                {
                    zoneInfo.SetIsKeepout( false );
                    edited = InvokeCopperZonesEditor( this, &zoneInfo );
                }
            }
            else   // Put a zone on a non copper layer (technical layer)
            {
                zoneInfo.SetIsKeepout( false );
//.........这里部分代码省略.........