C++ ZONE_CONTAINER::SetNetCode方法代码示例

void PCB_POLYGON::AddToBoard()
{
    int i = 0;

    if( m_outline.GetCount() > 0 )
    {
        ZONE_CONTAINER* zone = new ZONE_CONTAINER( m_board );
        m_board->Add( zone, ADD_APPEND );

        zone->SetTimeStamp( m_timestamp );
        zone->SetLayer( m_KiCadLayer );
        zone->SetNetCode( m_netCode );

        // add outline
        int outline_hatch = ZONE_CONTAINER::DIAGONAL_EDGE;

        for( i = 0; i < (int) m_outline.GetCount(); i++ )
        {
            zone->AppendCorner( wxPoint( KiROUND( m_outline[i]->x ),
                                         KiROUND( m_outline[i]->y ) ), -1 );
        }

        zone->SetZoneClearance( m_width );

        zone->SetPriority( m_priority );

        zone->SetHatch( outline_hatch, zone->GetDefaultHatchPitch(), true );

        if ( m_objType == wxT( 'K' ) )
        {
            zone->SetIsKeepout( true );
            zone->SetDoNotAllowTracks( true );
            zone->SetDoNotAllowVias( true );
            zone->SetDoNotAllowCopperPour( true );
        }
        else if( m_objType == wxT( 'C' ) )
        {
            // convert cutouts to keepouts because standalone cutouts are not supported in KiCad
            zone->SetIsKeepout( true );
            zone->SetDoNotAllowCopperPour( true );
        }

        //if( m_filled )
        //    zone->BuildFilledPolysListData( m_board );
    }
}

int PCB_EDIT_FRAME::Begin_Zone( wxDC* DC )
{
    ZONE_SETTINGS zoneInfo = GetZoneSettings();

    // verify if s_CurrentZone exists (could be deleted since last selection) :
    int ii;
    for( ii = 0; ii < GetBoard()->GetAreaCount(); ii++ )
    {
        if( s_CurrentZone == GetBoard()->GetArea( ii ) )
            break;
    }

    if( ii >= GetBoard()->GetAreaCount() ) // Not found: could be deleted since last selection
    {
        s_AddCutoutToCurrentZone = false;
        s_CurrentZone = NULL;
    }

    ZONE_CONTAINER* zone = GetBoard()->m_CurrentZoneContour;

    // Verify if a new zone is allowed on this layer:
    if( zone == NULL  )
    {
        if( GetToolId() == ID_PCB_KEEPOUT_AREA_BUTT && !IsCopperLayer( GetActiveLayer() ) )
        {
            DisplayError( this,
                          _( "Error: a keepout area is allowed only on copper layers" ) );
            return 0;
        }
    }

    // If no zone contour in progress, a new zone is being created,
    if( zone == NULL )
    {
        zone = GetBoard()->m_CurrentZoneContour = new ZONE_CONTAINER( GetBoard() );
        zone->SetFlags( IS_NEW );
        zone->SetTimeStamp( GetNewTimeStamp() );
    }

    if( zone->GetNumCorners() == 0 )    // Start a new contour: init zone params (net, layer ...)
    {
        if( !s_CurrentZone )            // A new outline is created, from scratch
        {
            ZONE_EDIT_T edited;

            // Init zone params to reasonable values
            zone->SetLayer( GetActiveLayer() );

            // Prompt user for parameters:
            m_canvas->SetIgnoreMouseEvents( true );

            if( zone->IsOnCopperLayer() )
            {
                // Put a zone on a copper layer
                if( GetBoard()->GetHighLightNetCode() > 0 )
                {
                    zoneInfo.m_NetcodeSelection = GetBoard()->GetHighLightNetCode();
                    zone->SetNetCode( zoneInfo.m_NetcodeSelection );
                }

                double tmp = ZONE_THERMAL_RELIEF_GAP_MIL;

                wxConfigBase* cfg = Kiface().KifaceSettings();
                cfg->Read( ZONE_THERMAL_RELIEF_GAP_STRING_KEY, &tmp );
                zoneInfo.m_ThermalReliefGap = KiROUND( tmp * IU_PER_MILS);

                tmp = ZONE_THERMAL_RELIEF_COPPER_WIDTH_MIL;
                cfg->Read( ZONE_THERMAL_RELIEF_COPPER_WIDTH_STRING_KEY, &tmp );
                zoneInfo.m_ThermalReliefCopperBridge = KiROUND( tmp * IU_PER_MILS );

                tmp = ZONE_CLEARANCE_MIL;
                cfg->Read( ZONE_CLEARANCE_WIDTH_STRING_KEY, &tmp );
                zoneInfo.m_ZoneClearance = KiROUND( tmp * IU_PER_MILS );

                tmp = ZONE_THICKNESS_MIL;
                cfg->Read( ZONE_MIN_THICKNESS_WIDTH_STRING_KEY, &tmp );
                zoneInfo.m_ZoneMinThickness = KiROUND( tmp * IU_PER_MILS );

                zoneInfo.m_CurrentZone_Layer = zone->GetLayer();

                if( GetToolId() == ID_PCB_KEEPOUT_AREA_BUTT )
                {
                    zoneInfo.SetIsKeepout( true );
                    // Netcode, netname and some other settings are irrelevant,
                    // so ensure they are cleared
                    zone->SetNetCode( NETINFO_LIST::UNCONNECTED );
                    zoneInfo.SetCornerSmoothingType( ZONE_SETTINGS::SMOOTHING_NONE );
                    zoneInfo.SetCornerRadius( 0 );

                    edited = InvokeKeepoutAreaEditor( this, &zoneInfo );
                }
                else
                {
                    zoneInfo.SetIsKeepout( false );
                    edited = InvokeCopperZonesEditor( this, &zoneInfo );
                }
            }
            else   // Put a zone on a non copper layer (technical layer)
            {
                zoneInfo.SetIsKeepout( false );
//.........这里部分代码省略.........