C++ ZONE_CONTAINER::SetNet方法代码示例

void ZONE_SETTINGS::ExportSetting( ZONE_CONTAINER& aTarget, bool aFullExport ) const
{
    aTarget.SetFillMode( m_FillMode );
    aTarget.SetZoneClearance( m_ZoneClearance );
    aTarget.SetMinThickness( m_ZoneMinThickness );
    aTarget.SetArcSegmentCount( m_ArcToSegmentsCount );
    aTarget.SetThermalReliefGap( m_ThermalReliefGap );
    aTarget.SetThermalReliefCopperBridge( m_ThermalReliefCopperBridge );
    aTarget.SetPadConnection( m_PadConnection );
    aTarget.SetCornerSmoothingType( m_cornerSmoothingType );
    aTarget.SetCornerRadius( m_cornerRadius );
    aTarget.SetIsKeepout( GetIsKeepout() );
    aTarget.SetDoNotAllowCopperPour( GetDoNotAllowCopperPour() );
    aTarget.SetDoNotAllowVias( GetDoNotAllowVias() );
    aTarget.SetDoNotAllowTracks( GetDoNotAllowTracks() );

    if( aFullExport )
    {
        aTarget.SetPriority( m_ZonePriority );
        aTarget.SetNet( m_NetcodeSelection );
        aTarget.SetLayer( m_CurrentZone_Layer );
        aTarget.Outline()->SetLayer( m_CurrentZone_Layer );
    }

    // call SetHatch last, because hatch lines will be rebuilt,
    // using new parameters values
    aTarget.Outline()->SetHatch( m_Zone_HatchingStyle, Mils2iu( 20 ), true );
}

int PCB_EDIT_FRAME::Begin_Zone( wxDC* DC )
{
    ZONE_SETTINGS zoneInfo = GetZoneSettings();

    // verify if s_CurrentZone exists (could be deleted since last selection) :
    int ii;
    for( ii = 0; ii < GetBoard()->GetAreaCount(); ii++ )
    {
        if( s_CurrentZone == GetBoard()->GetArea( ii ) )
            break;
    }

    if( ii >= GetBoard()->GetAreaCount() ) // Not found: could be deleted since last selection
    {
        s_AddCutoutToCurrentZone = false;
        s_CurrentZone = NULL;
    }

    // If no zone contour in progress, a new zone is being created:
    if( !GetBoard()->m_CurrentZoneContour )
    {
        if( GetToolId() == ID_PCB_KEEPOUT_AREA_BUTT &&
            getActiveLayer() >= FIRST_NON_COPPER_LAYER )
        {
            DisplayError( this,
                          _( "Error: a keepout area is allowed only on copper layers" ) );
            return 0;
        }
        else
            GetBoard()->m_CurrentZoneContour = new ZONE_CONTAINER( GetBoard() );
    }

    ZONE_CONTAINER* zone = GetBoard()->m_CurrentZoneContour;

    if( zone->GetNumCorners() == 0 )    // Start a new contour: init zone params (net, layer ...)
    {
        if( !s_CurrentZone )            // A new outline is created, from scratch
        {
            ZONE_EDIT_T edited;

            // Init zone params to reasonable values
            zone->SetLayer( getActiveLayer() );

            // Prompt user for parameters:
            m_canvas->SetIgnoreMouseEvents( true );

            if( zone->IsOnCopperLayer() )
            {
                // Put a zone on a copper layer
                if( GetBoard()->GetHighLightNetCode() > 0 )
                {
                    zoneInfo.m_NetcodeSelection = GetBoard()->GetHighLightNetCode();

                    zone->SetNet( zoneInfo.m_NetcodeSelection );
                    zone->SetNetNameFromNetCode( );
                }
                double tmp = ZONE_THERMAL_RELIEF_GAP_MIL;
                wxGetApp().GetSettings()->Read( ZONE_THERMAL_RELIEF_GAP_STRING_KEY, &tmp );
                zoneInfo.m_ThermalReliefGap = KiROUND( tmp * IU_PER_MILS);

                tmp = ZONE_THERMAL_RELIEF_COPPER_WIDTH_MIL;
                wxGetApp().GetSettings()->Read( ZONE_THERMAL_RELIEF_COPPER_WIDTH_STRING_KEY,
                                                &tmp );
                zoneInfo.m_ThermalReliefCopperBridge = KiROUND( tmp * IU_PER_MILS );

                tmp = ZONE_CLEARANCE_MIL;
                wxGetApp().GetSettings()->Read( ZONE_CLEARANCE_WIDTH_STRING_KEY,
                                                &tmp );
                zoneInfo.m_ZoneClearance = KiROUND( tmp * IU_PER_MILS );

                tmp = ZONE_THICKNESS_MIL;
                wxGetApp().GetSettings()->Read( ZONE_MIN_THICKNESS_WIDTH_STRING_KEY,
                                                &tmp );
                zoneInfo.m_ZoneMinThickness = KiROUND( tmp * IU_PER_MILS );

                zoneInfo.m_CurrentZone_Layer = zone->GetLayer();

                if( GetToolId() == ID_PCB_KEEPOUT_AREA_BUTT )
                {
                    zoneInfo.SetIsKeepout( true );
                    edited = InvokeKeepoutAreaEditor( this, &zoneInfo );
                }
                else
                {
                    zoneInfo.SetIsKeepout( false );
                    edited = InvokeCopperZonesEditor( this, &zoneInfo );
                }
            }
            else   // Put a zone on a non copper layer (technical layer)
            {
                zoneInfo.SetIsKeepout( false );
                zoneInfo.m_NetcodeSelection = 0;     // No net for non copper zones
                edited = InvokeNonCopperZonesEditor( this, zone, &zoneInfo );
            }

            m_canvas->MoveCursorToCrossHair();
            m_canvas->SetIgnoreMouseEvents( false );

            if( edited == ZONE_ABORT )
                return 0;
//.........这里部分代码省略.........