C++ DEVICE::at_weot方法代码示例

/*
 * This job is done, so release the device. From a Unix standpoint,
 *  the device remains open.
 *
 * Note, if we were spooling, we may enter with the device blocked.
 *   We unblock at the end, only if it was us who blocked the
 *   device.
 *
 */
bool release_device(DCR *dcr)
{
   utime_t now;
   JCR *jcr = dcr->jcr;
   DEVICE *dev = dcr->dev;
   bool ok = true;
   char tbuf[100];
   int was_blocked = BST_NOT_BLOCKED;

   /*
    * Capture job statistics now that we are done using this device.
    */
   now = (utime_t)time(NULL);
   update_job_statistics(jcr, now);

   dev->Lock();
   if (!dev->is_blocked()) {
      block_device(dev, BST_RELEASING);
   } else {
      was_blocked = dev->blocked();
      dev->set_blocked(BST_RELEASING);
   }
   lock_volumes();
   Dmsg2(100, "release_device device %s is %s\n", dev->print_name(), dev->is_tape() ? "tape" : "disk");

   /*
    * If device is reserved, job never started, so release the reserve here
    */
   dcr->clear_reserved();

   if (dev->can_read()) {
      VOLUME_CAT_INFO *vol = &dev->VolCatInfo;
      dev->clear_read();              /* clear read bit */
      Dmsg2(150, "dir_update_vol_info. label=%d Vol=%s\n",
         dev->is_labeled(), vol->VolCatName);
      if (dev->is_labeled() && vol->VolCatName[0] != 0) {
         dcr->dir_update_volume_info(false, false); /* send Volume info to Director */
         remove_read_volume(jcr, dcr->VolumeName);
         volume_unused(dcr);
      }
   } else if (dev->num_writers > 0) {
      /*
       * Note if WEOT is set, we are at the end of the tape and may not be positioned correctly,
       * so the job_media_record and update_vol_info have already been done,
       * which means we skip them here.
       */
      dev->num_writers--;
      Dmsg1(100, "There are %d writers in release_device\n", dev->num_writers);
      if (dev->is_labeled()) {
         Dmsg2(200, "dir_create_jobmedia. Release vol=%s dev=%s\n",
               dev->getVolCatName(), dev->print_name());
         if (!dev->at_weot() && !dcr->dir_create_jobmedia_record(false)) {
            Jmsg2(jcr, M_FATAL, 0, _("Could not create JobMedia record for Volume=\"%s\" Job=%s\n"),
               dcr->getVolCatName(), jcr->Job);
         }

         /*
          * If no more writers, and no errors, and wrote something, write an EOF
          */
         if (!dev->num_writers && dev->can_write() && dev->block_num > 0) {
            dev->weof(1);
            write_ansi_ibm_labels(dcr, ANSI_EOF_LABEL, dev->VolHdr.VolumeName);
         }
         if (!dev->at_weot()) {
            dev->VolCatInfo.VolCatFiles = dev->file;   /* set number of files */

            /*
             * Note! do volume update before close, which zaps VolCatInfo
             */
            dcr->dir_update_volume_info(false, false); /* send Volume info to Director */
            Dmsg2(200, "dir_update_vol_info. Release vol=%s dev=%s\n",
                  dev->getVolCatName(), dev->print_name());
         }
         if (dev->num_writers == 0) {         /* if not being used */
            volume_unused(dcr);               /*  we obviously are not using the volume */
         }
      }

   } else {
      /*
       * If we reach here, it is most likely because the job has failed,
       * since the device is not in read mode and there are no writers.
       * It was probably reserved.
       */
      volume_unused(dcr);
   }

   Dmsg3(100, "%d writers, %d reserve, dev=%s\n", dev->num_writers, dev->num_reserved(), dev->print_name());

   /*
    * If no writers, close if file or !CAP_ALWAYS_OPEN
//.........这里部分代码省略.........