Python PyMata.i2c_config方法代码示例

# 需要导入模块: from PyMata.pymata import PyMata [as 别名]
# 或者: from PyMata.pymata.PyMata import i2c_config [as 别名]
import time
from PyMata.pymata import PyMata

addr = 0x48
# Initialize Arduino using port name
port = PyMata("/dev/cu.usbmodem621")

# Configure I2C pin
port.i2c_config(0, port.ANALOG, 4, 5)

# one shot read asking peripheral to send 2 bytes
port.i2c_read(addr, 0, 2, port.I2C_READ)

# Wait for peripheral to send the data
time.sleep(3)

# Read from the peripheral
data = port.i2c_get_read_data(addr)

# Obtain temperature from received data
TemperatureSum = (data[1] << 8 | data[2]) >> 4

celsius = TemperatureSum * 0.0625
print celsius

fahrenheit = (1.8 * celsius) + 32
print fahrenheit

firmata.close()

# 需要导入模块: from PyMata.pymata import PyMata [as 别名]
# 或者: from PyMata.pymata.PyMata import i2c_config [as 别名]
class BiColorDisplayController:
    # display blink control values

    board_address = 0 # i2c address
    blink_rate = 0  # blink rate
    brightness = 0 # brightness

    # blink rate defines
    HT16K33_BLINK_CMD = 0x80
    HT16K33_BLINK_DISPLAYON = 0x01
    HT16K33_BLINK_OFF = 0
    HT16K33_BLINK_2HZ = 1
    HT16K33_BLINK_1HZ = 2
    HT16K33_BLINK_HALFHZ = 3

    # oscillator control values
    OSCILLATOR_ON = 0x21
    OSCILLATOR_OFF = 0x20

    # led color selectors
    LED_OFF = 0
    LED_RED = 1
    LED_YELLOW = 2
    LED_GREEN = 3

    # brightness
    MAX_BRIGHTNESS = 15

    # the display buffer
    # This is an 16x16 matrix that stores pixel data for the display
    # Even rows store the green pixel data and odd rows store the red pixel data.
    #
    # A physical row on the device is controlled by a row pair (ie 0,1 and 2,3, etc) for the 2 colors.
    #
    # To output yellow the red and green information for the rows will be set high.
    #
    display_buffer = [[0 for x in xrange(8)] for x in xrange(8)]


    def __init__(self, address, blink_rate, brightness):

        # create an instance of PyMata - we are using an Arduino UNO
        """

        @param address: I2C address of the device
        @param blink_rate: desired blink rate
        @param brightness: brightness level for the display
        """
        self.firmata = PyMata("/dev/ttyACM0")

        self.board_address = address
        self.blink_rate = blink_rate
        self.brightness = brightness
        self.clear_display_buffer()

        # configure firmata for i2c on an UNO
        self.firmata.i2c_config(0, self.firmata.ANALOG, 4, 5)

        # turn on oscillator
        self.oscillator_set(self.OSCILLATOR_ON)

        # set blink rate
        self.set_blink_rate(self.blink_rate)

        # set brightness
        self.set_brightness(self.brightness)

    def set_blink_rate(self, b):
        """
        Set the user's desired blink rate (0 - 3)
        @param b: blink rate
        """
        if (b > 3):
            b = 0 # turn off if not sure
        self.firmata.i2c_write(self.board_address,
                                 (self.HT16K33_BLINK_CMD | self.HT16K33_BLINK_DISPLAYON | (b << 1)))

    def oscillator_set(self, osc_mode):
        """
        Turn oscillator on or off
        @param osc_mode: osc mode (OSCILLATOR_ON or OSCILLATOR_OFF)
        """
        self.firmata.i2c_write(self.board_address, osc_mode)

    def set_brightness(self, brightness):
        """
        Set the brightness level for the entire display
        @param brightness: brightness level (0 -15)
        """
        if brightness > 15:
            brightness = 15
        brightness |= 0xE0
        self.brightness = brightness
        self.firmata.i2c_write(0x70,  brightness)

    def set_pixel(self, row, column, color, suppress_write):
        # rows 0,2,4,6,8,10,12,14 are green
        # rows 1,3,5,7,9,11,13,15 are red
        #
        # A row entry consists of 2 bytes, the first always being 0 and the second
#.........这里部分代码省略.........

# 需要导入模块: from PyMata.pymata import PyMata [as 别名]
# 或者: from PyMata.pymata.PyMata import i2c_config [as 别名]

# create a PyMata instance
board = PyMata("/dev/ttyACM0")


def signal_handler(sig, frame):
    print('You pressed Ctrl+C!!!!')
    if board is not None:
        board.reset()
    sys.exit(0)


signal.signal(signal.SIGINT, signal_handler)

# configure firmata for i2c on an UNO
board.i2c_config(0, board.ANALOG, 4, 5)

# configure the I2C pins. This code is for the Leonardo
# board.i2c_config(0, board.DIGITAL, 3, 2)

# read i2c device at address 0x48, with no register specified. Expect 2 bytes to be returned
# and the operation is a single shot read
board.i2c_read(0x48, 0, 2, board.I2C_READ, temp_callback)

# give the serial interface time to send a read, for the device to execute the read
# and to get things back across the interface
time.sleep(2)

board.close()

# 需要导入模块: from PyMata.pymata import PyMata [as 别名]
# 或者: from PyMata.pymata.PyMata import i2c_config [as 别名]
"""

# import the API class
import time

from PyMata.pymata import PyMata



# The PyMata constructor will print status to the console and will return
# when PyMata is ready to accept commands or will exit if unsuccessful
firmata = PyMata("/dev/ttyACM0")

#configure the I2C pins. This code is for the UNO

firmata.i2c_config(0, firmata.ANALOG, 4, 5)

# read i2c device at address 0x48, with no register specified. Expect 2 bytes to be returned
# and the operation is a single shot read
firmata.i2c_read(0x48, 0, 2, firmata.I2C_READ)

# give the serial interface time to send a read, for the device to execute the read
# and to get things back across the interface
time.sleep(3)

# retrieve the data sent from device
data = firmata.i2c_get_read_data(0x48)

# do some calculations on the raw data returned
TemperatureSum = (data[1] << 8 | data[2]) >> 4

# 需要导入模块: from PyMata.pymata import PyMata [as 别名]
# 或者: from PyMata.pymata.PyMata import i2c_config [as 别名]
from PyMata.pymata import PyMata
import sys
import time
import signal

board = PyMata("/dev/ttyACM0")

# for leonardo
board.i2c_config(0, board.DIGITAL, 3, 2)


# for uno
# board.i2c_config(0, board.ANALOG, 4, 5)

def signal_handler(sig, frame):
    print('You pressed Ctrl+C!!!!')
    if board is not None:
        board.reset()
    sys.exit(0)


signal.signal(signal.SIGINT, signal_handler)


def lux_callback(data):
    datax = data[2]
    print('Got read data: %s' % data)
    lux = (datax[1] << 8 | datax[2]) >> 4
    lux /= 1.2
    print(str(lux) + ' lux')