本文整理汇总了C++中GCodeExport::setFilename方法的典型用法代码示例。如果您正苦于以下问题：C++ GCodeExport::setFilename方法的具体用法？C++ GCodeExport::setFilename怎么用？C++ GCodeExport::setFilename使用的例子？那么, 这里精选的方法代码示例或许可以为您提供帮助。您也可以进一步了解该方法所在类GCodeExport的用法示例。
在下文中一共展示了GCodeExport::setFilename方法的1个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于系统推荐出更棒的C++代码示例。
示例1: main
int main(int argc, char **argv)
{
#if defined(__linux__) || (defined(__APPLE__) && defined(__MACH__))
//Lower the process priority on linux and mac.
setpriority(PRIO_PROCESS, 0, 10);
#endif
signal(SIGFPE, signal_FPE);
GCodeExport gcode;
Config config;
int fileNr = 0;
config.filamentDiameter = 2890;
config.filamentFlow = 100;
config.initialLayerThickness = 300;
config.layerThickness = 100;//100
config.extrusionWidth = 400;
config.insetCount = 2;
config.downSkinCount = 6;
config.upSkinCount = 6;
config.initialSpeedupLayers = 4;
config.initialLayerSpeed = 20;
config.printSpeed = 50;
config.infillSpeed = 50;
config.moveSpeed = 200;
config.fanOnLayerNr = 2;
config.skirtDistance = 6000;
config.skirtLineCount = 1;
config.sparseInfillLineDistance = 100 * config.extrusionWidth / 20;
config.infillOverlap = 15;//15
config.objectPosition = Point(102500, 102500);
config.objectSink = 0;
config.supportAngle = -1;
config.supportEverywhere = 0;
config.supportLineWidth = config.extrusionWidth;
config.retractionAmount = 4.5;
config.retractionSpeed = 45;
config.retractionAmountExtruderSwitch = 14.5;
config.multiVolumeOverlap = 0;
config.minimalLayerTime = 5;
config.minimalFeedrate = 10;
config.coolHeadLift = 1;
config.fanSpeedMin = 100;
config.fanSpeedMax = 100;
config.raftMargin = 5000;
config.raftLineSpacing = 1000;
config.raftBaseThickness = 0;
config.raftBaseLinewidth = 0;
config.raftInterfaceThickness = 0;
config.raftInterfaceLinewidth = 0;
config.fixHorrible = 0;
config.startCode =
"M109 S210 ;Heatup to 210C\n"
"G21 ;metric values\n"
"G90 ;absolute positioning\n"
"G28 ;Home\n"
"G1 Z15.0 F300 ;move the platform down 15mm\n"
"G92 E0 ;zero the extruded length\n"
"G1 F200 E5 ;extrude 5mm of feed stock\n"
"G92 E0 ;zero the extruded length again\n";
config.endCode =
"M104 S0 ;extruder heater off\n"
"M140 S0 ;heated bed heater off (if you have it)\n"
"G91 ;relative positioning\n"
"G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\n"
"G1 Z+0.5 E-5 X-20 Y-20 F9000 ;move Z up a bit and retract filament even more\n"
"G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\n"
"M84 ;steppers off\n"
"G90 ;absolute positioning\n";
fprintf(stdout,"Cura_SteamEngine version %s\n", VERSION);
for(int argn = 1; argn < argc; argn++)
{
char* str = argv[argn];
if (str[0] == '-')
{
for(str++; *str; str++)
{
switch(*str)
{
case 'h':
print_usage();
exit(1);
case 'v':
verbose_level++;
break;
case 'b':
argn++;
binaryMeshBlob = fopen(argv[argn], "rb");
break;
case 'o':
argn++;
gcode.setFilename(argv[argn]);
if (!gcode.isValid())
{
//.........这里部分代码省略.........