本文整理匯總了Python中Path.Path.add_slave方法的典型用法代碼示例。如果您正苦於以下問題：Python Path.add_slave方法的具體用法？Python Path.add_slave怎麽用？Python Path.add_slave使用的例子？那麽, 這裏精選的方法代碼示例或許可以為您提供幫助。您也可以進一步了解該方法所在類Path.Path的用法示例。
在下文中一共展示了Path.add_slave方法的1個代碼示例，這些例子默認根據受歡迎程度排序。您可以為喜歡或者感覺有用的代碼點讚，您的評價將有助於係統推薦出更棒的Python代碼示例。
示例1: __init__
# 需要導入模塊: from Path import Path [as 別名]
# 或者: from Path.Path import add_slave [as 別名]
#.........這裏部分代碼省略.........
printer.steppers["E"] = Stepper_00B3("GPIO1_28", "GPIO1_15", 93, 14, 3, "E")
printer.steppers["H"] = Stepper_00B3("GPIO1_13", "GPIO1_14", 94, 15, 4, "H")
elif self.revision in ["00A4", "0A4A"]:
printer.steppers["X"] = Stepper_00A4("GPIO0_27", "GPIO1_29", "GPIO2_4" , 0, 0, "X")
printer.steppers["Y"] = Stepper_00A4("GPIO1_12", "GPIO0_22", "GPIO2_5" , 1, 1, "Y")
printer.steppers["Z"] = Stepper_00A4("GPIO0_23", "GPIO0_26", "GPIO0_15", 2, 2, "Z")
printer.steppers["E"] = Stepper_00A4("GPIO1_28", "GPIO1_15", "GPIO2_1" , 3, 3, "E")
printer.steppers["H"] = Stepper_00A4("GPIO1_13", "GPIO1_14", "GPIO2_3" , 4, 4, "H")
# Init Reach steppers, if present.
if printer.config.reach_revision == "00A0":
printer.steppers["A"] = Stepper_reach_00A4("GPIO2_2" , "GPIO1_18", "GPIO0_14", 5, 5, "A")
printer.steppers["B"] = Stepper_reach_00A4("GPIO1_16", "GPIO0_5" , "GPIO0_14", 6, 6, "B")
printer.steppers["C"] = Stepper_reach_00A4("GPIO0_3" , "GPIO3_19", "GPIO0_14", 7, 7, "C")
elif printer.config.reach_revision == "00B0":
printer.steppers["A"] = Stepper_reach_00B0("GPIO1_16", "GPIO0_5", "GPIO0_3", 5, 5, "A")
printer.steppers["B"] = Stepper_reach_00B0("GPIO2_2" , "GPIO0_14", "GPIO0_3", 6, 6, "B")
# Enable the steppers and set the current, steps pr mm and
# microstepping
for name, stepper in self.printer.steppers.iteritems():
stepper.in_use = printer.config.getboolean('Steppers', 'in_use_' + name)
stepper.direction = printer.config.getint('Steppers', 'direction_' + name)
stepper.has_endstop = printer.config.getboolean('Endstops', 'has_' + name)
stepper.set_current_value(printer.config.getfloat('Steppers', 'current_' + name))
stepper.set_steps_pr_mm(printer.config.getfloat('Steppers', 'steps_pr_mm_' + name))
stepper.set_microstepping(printer.config.getint('Steppers', 'microstepping_' + name))
stepper.set_decay(printer.config.getint("Steppers", "slow_decay_" + name))
# Add soft end stops
Path.soft_min[Path.axis_to_index(name)] = printer.config.getfloat('Endstops', 'soft_end_stop_min_' + name)
Path.soft_max[Path.axis_to_index(name)] = printer.config.getfloat('Endstops', 'soft_end_stop_max_' + name)
slave = printer.config.get('Steppers', 'slave_' + name)
if slave:
Path.add_slave(name, slave)
logging.debug("Axis "+name+" has slave "+slave)
# Commit changes for the Steppers
#Stepper.commit()
Stepper.printer = printer
# Delta printer setup
if Path.axis_config == Path.AXIS_CONFIG_DELTA:
opts = ["Hez", "L", "r", "Ae", "Be", "Ce", "A_radial", "B_radial", "C_radial", "A_tangential", "B_tangential", "C_tangential" ]
for opt in opts:
Delta.__dict__[opt] = printer.config.getfloat('Delta', opt)
Delta.recalculate()
# Discover and add all DS18B20 cold ends.
import glob
paths = glob.glob("/sys/bus/w1/devices/28-*/w1_slave")
logging.debug("Found cold ends: "+str(paths))
for i, path in enumerate(paths):
self.printer.cold_ends.append(ColdEnd(path, "ds18b20-"+str(i)))
logging.info("Found Cold end "+str(i)+" on " + path)
# Make Mosfets, thermistors and extruders
heaters = ["E", "H", "HBP"]
if self.printer.config.reach_revision:
heaters.extend(["A", "B", "C"])
for e in heaters:
# Mosfets
channel = self.printer.config.getint("Heaters", "mosfet_"+e)
self.printer.mosfets[e] = Mosfet(channel)
# Thermistors