C++ AP_RangeFinder_Backend::get_pos_offset方法代码示例

const Vector3f &RangeFinder::get_pos_offset_orient(enum Rotation orientation) const
{
    AP_RangeFinder_Backend *backend = find_instance(orientation);
    if (backend == nullptr) {
        return pos_offset_zero;
    }
    return backend->get_pos_offset();
}

// select the height measurement to be fused from the available baro, range finder and GPS sources
void NavEKF2_core::selectHeightForFusion()
{
    // Read range finder data and check for new data in the buffer
    // This data is used by both height and optical flow fusion processing
    readRangeFinder();
    rangeDataToFuse = storedRange.recall(rangeDataDelayed,imuDataDelayed.time_ms);

    // correct range data for the body frame position offset relative to the IMU
    // the corrected reading is the reading that would have been taken if the sensor was
    // co-located with the IMU
    if (rangeDataToFuse) {
        AP_RangeFinder_Backend *sensor = frontend->_rng.get_backend(rangeDataDelayed.sensor_idx);
        if (sensor != nullptr) {
            Vector3f posOffsetBody = sensor->get_pos_offset() - accelPosOffset;
            if (!posOffsetBody.is_zero()) {
                Vector3f posOffsetEarth = prevTnb.mul_transpose(posOffsetBody);
                rangeDataDelayed.rng += posOffsetEarth.z / prevTnb.c.z;
            }
        }
    }

    // read baro height data from the sensor and check for new data in the buffer
    readBaroData();
    baroDataToFuse = storedBaro.recall(baroDataDelayed, imuDataDelayed.time_ms);

    // select height source
    if (extNavUsedForPos) {
        // always use external vision as the hight source if using for position.
        activeHgtSource = HGT_SOURCE_EV;
    } else if (((frontend->_useRngSwHgt > 0) || (frontend->_altSource == 1)) && (imuSampleTime_ms - rngValidMeaTime_ms < 500)) {
        if (frontend->_altSource == 1) {
            // always use range finder
            activeHgtSource = HGT_SOURCE_RNG;
        } else {
            // determine if we are above or below the height switch region
            float rangeMaxUse = 1e-4f * (float)frontend->_rng.max_distance_cm_orient(ROTATION_PITCH_270) * (float)frontend->_useRngSwHgt;
            bool aboveUpperSwHgt = (terrainState - stateStruct.position.z) > rangeMaxUse;
            bool belowLowerSwHgt = (terrainState - stateStruct.position.z) < 0.7f * rangeMaxUse;

            // If the terrain height is consistent and we are moving slowly, then it can be
            // used as a height reference in combination with a range finder
            // apply a hysteresis to the speed check to prevent rapid switching
            float horizSpeed = norm(stateStruct.velocity.x, stateStruct.velocity.y);
            bool dontTrustTerrain = ((horizSpeed > frontend->_useRngSwSpd) && filterStatus.flags.horiz_vel) || !terrainHgtStable;
            float trust_spd_trigger = MAX((frontend->_useRngSwSpd - 1.0f),(frontend->_useRngSwSpd * 0.5f));
            bool trustTerrain = (horizSpeed < trust_spd_trigger) && terrainHgtStable;

            /*
             * Switch between range finder and primary height source using height above ground and speed thresholds with
             * hysteresis to avoid rapid switching. Using range finder for height requires a consistent terrain height
             * which cannot be assumed if the vehicle is moving horizontally.
            */
            if ((aboveUpperSwHgt || dontTrustTerrain) && (activeHgtSource == HGT_SOURCE_RNG)) {
                // cannot trust terrain or range finder so stop using range finder height
                if (frontend->_altSource == 0) {
                    activeHgtSource = HGT_SOURCE_BARO;
                } else if (frontend->_altSource == 2) {
                    activeHgtSource = HGT_SOURCE_GPS;
                }
            } else if (belowLowerSwHgt && trustTerrain && (activeHgtSource != HGT_SOURCE_RNG)) {
                // reliable terrain and range finder so start using range finder height
                activeHgtSource = HGT_SOURCE_RNG;
            }
        }
    } else if ((frontend->_altSource == 2) && ((imuSampleTime_ms - lastTimeGpsReceived_ms) < 500) && validOrigin && gpsAccuracyGood) {
        activeHgtSource = HGT_SOURCE_GPS;
    } else if ((frontend->_altSource == 3) && validOrigin && rngBcnGoodToAlign) {
        activeHgtSource = HGT_SOURCE_BCN;
    } else {
        activeHgtSource = HGT_SOURCE_BARO;
    }

    // Use Baro alt as a fallback if we lose range finder, GPS or external nav
    bool lostRngHgt = ((activeHgtSource == HGT_SOURCE_RNG) && ((imuSampleTime_ms - rngValidMeaTime_ms) > 500));
    bool lostGpsHgt = ((activeHgtSource == HGT_SOURCE_GPS) && ((imuSampleTime_ms - lastTimeGpsReceived_ms) > 2000));
    bool lostExtNavHgt = ((activeHgtSource == HGT_SOURCE_EV) && ((imuSampleTime_ms - extNavMeasTime_ms) > 2000));
    if (lostRngHgt || lostGpsHgt || lostExtNavHgt) {
        activeHgtSource = HGT_SOURCE_BARO;
    }

    // if there is new baro data to fuse, calculate filtered baro data required by other processes
    if (baroDataToFuse) {
        // calculate offset to baro data that enables us to switch to Baro height use during operation
        if  (activeHgtSource != HGT_SOURCE_BARO) {
            calcFiltBaroOffset();
        }
        // filtered baro data used to provide a reference for takeoff
        // it is is reset to last height measurement on disarming in performArmingChecks()
        if (!getTakeoffExpected()) {
            const float gndHgtFiltTC = 0.5f;
            const float dtBaro = frontend->hgtAvg_ms*1.0e-3f;
            float alpha = constrain_float(dtBaro / (dtBaro+gndHgtFiltTC),0.0f,1.0f);
            meaHgtAtTakeOff += (baroDataDelayed.hgt-meaHgtAtTakeOff)*alpha;
        }
    }

    // If we are not using GPS as the primary height sensor, correct EKF origin height so that
    // combined local NED position height and origin height remains consistent with the GPS altitude
    // This also enables the GPS height to be used as a backup height source
//.........这里部分代码省略.........