本文整理匯總了C#中Circuit.stampNonLinear方法的典型用法代碼示例。如果您正苦於以下問題：C# Circuit.stampNonLinear方法的具體用法？C# Circuit.stampNonLinear怎麽用？C# Circuit.stampNonLinear使用的例子？那麽, 這裏精選的方法代碼示例或許可以為您提供幫助。您也可以進一步了解該方法所在類Circuit的用法示例。
在下文中一共展示了Circuit.stampNonLinear方法的8個代碼示例，這些例子默認根據受歡迎程度排序。您可以為喜歡或者感覺有用的代碼點讚，您的評價將有助於係統推薦出更棒的C#代碼示例。
示例1: stamp
public override void stamp(Circuit sim)
{
int vn = sim.nodeCount + pins[2].voltSource;
sim.stampNonLinear(vn);
sim.stampNonLinear(0);
sim.stampNonLinear(lead_node[2]);
}示例2: stamp
public override void stamp(Circuit sim)
{
// output pin
sim.stampVoltageSource(0, lead_node[1], pins[1].voltSource);
// attach Vi to R1 pin so its current is proportional to Vi
sim.stampVoltageSource(lead_node[0], lead_node[4], pins[4].voltSource, 0);
// attach 5V to R2 pin so we get a current going
sim.stampVoltageSource(0, lead_node[5], pins[5].voltSource, 5);
// put resistor across cap pins to give current somewhere to go
// in case cap is not connected
sim.stampResistor(lead_node[2], lead_node[3], cResistance);
sim.stampNonLinear(lead_node[2]);
sim.stampNonLinear(lead_node[3]);
}示例3: stamp
public override void stamp(Circuit sim)
{
sim.stampNonLinear(lead_node[0]);
sim.stampNonLinear(lead_node[1]);
}示例4: stamp
public override void stamp(Circuit sim)
{
sim.stampNonLinear(lead_node[anode]);
sim.stampNonLinear(lead_node[cnode]);
sim.stampNonLinear(lead_node[gnode]);
sim.stampNonLinear(lead_node[inode]);
sim.stampResistor(lead_node[gnode], lead_node[cnode], cresistance);
diode.stamp(sim, lead_node[inode], lead_node[gnode]);
}示例5: stamp
public void stamp(Circuit sim, int n0, int n1)
{
nodes[0] = n0;
nodes[1] = n1;
sim.stampNonLinear(nodes[0]);
sim.stampNonLinear(nodes[1]);
}示例6: stamp
public override void stamp(Circuit sim)
{
// stamp voltage divider to put ctl pin at 2/3 V
sim.stampResistor(lead_node[N_VIN], lead_node[N_CTL], 5000);
sim.stampResistor(lead_node[N_CTL], 0, 10000);
// output pin
sim.stampVoltageSource(0, lead_node[N_OUT], pins[N_OUT].voltSource);
// discharge pin
sim.stampNonLinear(lead_node[N_DIS]);
}示例7: stamp
public override void stamp(Circuit sim)
{
sim.stampVoltageSource(0, lead_node[3], voltSource);
sim.stampNonLinear(lead_node[3]);
sim.stampNonLinear(lead_node[1]);
}示例8: getVoltageText
/*public override void getInfo(String[] arr) {
arr[0] = "op-amp";
arr[1] = "V+ = " + getVoltageText(lead_volt[1]);
arr[2] = "V- = " + getVoltageText(lead_volt[0]);
// sometimes the voltage goes slightly outside range, to make
// convergence easier. so we hide that here.
double vo = Math.Max(Math.Min(lead_volt[2], maxOut), minOut);
arr[3] = "Vout = " + getVoltageText(vo);
arr[4] = "Iout = " + getCurrentText(current);
arr[5] = "range = " + getVoltageText(minOut) + " to " + getVoltageText(maxOut);
}*/
public override void stamp(Circuit sim)
{
int vn = sim.nodeCount + voltSource;
sim.stampNonLinear(vn);
sim.stampMatrix(lead_node[2], vn, 1);
}