Python time.sleep_ms函数代码示例

 def get_SHT_temperature(self):
  self._bus.writeto(self._address,TRI_T_MEASURE_NO_HOLD)
  sleep_ms(150)
  origin_data=self._bus.readfrom(self._address,2)
  origin_value=unp('>h',origin_data)[0]
  value=-46.85+175.72*(origin_value/65536)
  return value

    def blink_all_timed(self, color, blink_duration, brightness=1):
        """ Blink the entire stand at 2Hz for blink_duration, turns off afterwards
        
        Arguments:
            color : can be 'red', 'green', 'blue', 
                    or a tuple of (r,g,b) where r, g, and b are between 0 and 255
            blink_duration : duration to blink for in seconds
            brightness : between 0 and 1, 0 is off, 1 is full brightness
        """
        start_time = time.ticks_ms()
        
        run_time = time.ticks_diff(time.ticks_ms(), start_time) 
        
        while run_time/1000 < blink_duration:
            if run_time % 500 < 250: 
                self.turn_all_to_color(color, brightness)
            else:
                self.turn_all_off()
            
            time.sleep_ms(1)
            run_time = time.ticks_diff(time.ticks_ms(), start_time) 

        # Ensure that all are off 
        self.turn_all_off()
        

def main():
    # Executed on boot
    global switchPin
    global switchstate
    global lightstate
    switchPin = machine.Pin(13, machine.Pin.IN, machine.Pin.PULL_UP)
    cm.setAP(False)   # We don't want AP in work mode by default
    savedData = boot.readSession()
    lightstate = int(savedData[1])
    switchstate = int(savedData[2])
    triac.activate(lightstate)
    print("Bulb reinitialised")
    attemptConnect()

    # Main program
    while(MainLoop):
        global compareTime
        time.sleep_ms(checkFrequency)
        if time.ticks_diff(time.ticks_ms(), compareTime) > reconnAttemptInterval:
            attemptConnect()
            print("Done MQTT connect")
            compareTime = time.ticks_ms()
        if not emergencyMode:
            checkInputChange(0)
            if cm.mqttActive:
                mqtt.check_msg()
        else:
            checkInputChange(1)

    def __init__(self, i2c_bus):

        # create i2c obect
        _bmp_addr = self._bmp_addr
        self._bmp_i2c = i2c_bus
        self._bmp_i2c.start()
        self.chip_id = self._bmp_i2c.readfrom_mem(_bmp_addr, 0xD0, 2)
        # read calibration data from EEPROM
        self._AC1 = unp('>h', self._bmp_i2c.readfrom_mem(_bmp_addr, 0xAA, 2))[0]
        self._AC2 = unp('>h', self._bmp_i2c.readfrom_mem(_bmp_addr, 0xAC, 2))[0]
        self._AC3 = unp('>h', self._bmp_i2c.readfrom_mem(_bmp_addr, 0xAE, 2))[0]
        self._AC4 = unp('>H', self._bmp_i2c.readfrom_mem(_bmp_addr, 0xB0, 2))[0]
        self._AC5 = unp('>H', self._bmp_i2c.readfrom_mem(_bmp_addr, 0xB2, 2))[0]
        self._AC6 = unp('>H', self._bmp_i2c.readfrom_mem(_bmp_addr, 0xB4, 2))[0]
        self._B1 = unp('>h', self._bmp_i2c.readfrom_mem(_bmp_addr, 0xB6, 2))[0]
        self._B2 = unp('>h', self._bmp_i2c.readfrom_mem(_bmp_addr, 0xB8, 2))[0]
        self._MB = unp('>h', self._bmp_i2c.readfrom_mem(_bmp_addr, 0xBA, 2))[0]
        self._MC = unp('>h', self._bmp_i2c.readfrom_mem(_bmp_addr, 0xBC, 2))[0]
        self._MD = unp('>h', self._bmp_i2c.readfrom_mem(_bmp_addr, 0xBE, 2))[0]

        # settings to be adjusted by user
        self.oversample_setting = 3
        self.baseline = 101325.0

        # output raw
        self.UT_raw = None
        self.B5_raw = None
        self.MSB_raw = None
        self.LSB_raw = None
        self.XLSB_raw = None
        self.gauge = self.makegauge() # Generator instance
        for _ in range(128):
            next(self.gauge)
            time.sleep_ms(1)

 def activity(self):
     if not self.debounced:
         time.sleep_ms(self.act_dur)
         self.debounced = True
     if self.int_pin():
         return True
     return False

def playmusic():
    for i in range(0, len(musiclist), 1):
        display.show(str(musiclist[i]))
        music.pitch(round(round(tonelist[musiclist[i]])), PWM(Pin(27)))
        time.sleep_ms(round(500 * rhythmlist[i]))
        music.stop(PWM(Pin(27)))
        time.sleep_ms(10)

def diagnostic():

    n = np.n
    print("Count = ", n)

    cycle(3, 1000)
    cycle(10, 100)
    cycle(10, 50)
    cycle(10, 30)

    for j in range(0, 40):
        for i in range(0, n):
            r = 10
            if uos.urandom(1) <= b'\x30':
                r = 255

            np[(i-1) % n] = (0, 0, 0)
            np[i] = (r, 10, 10)
            np.write()

            time.sleep_ms(30)

    for j in range(255, 0, -5):
        for i in range(0, n):
            np[i] = (j, 0, 0)
            np.write()
            time.sleep_ms(10)

def cycle(iterations, speed):
    for i in range(0, iterations):
        for i in range(0, np.n):
            np[(i-1) % np.n] = (0, 0, 0)
            np[i] = (10, 10, 10)
            np.write()
            time.sleep_ms(speed)

 def get_SHT_relative_humidity(self):
  self._bus.writeto(self._address,TRI_RH_MEASURE_NO_HOLD)
  sleep_ms(150)
  origin_data=self._bus.readfrom(self._address,2)
  origin_value=unp('>H',origin_data)[0]
  value=-6+125*(origin_value/65536)
  return value

def rainbow_cycle(wait):
  for j in range(255):
    for i in range(n):
      rc_index = (i * 256 // n) + j
      np[i] = wheel(rc_index & 255)
    np.write()
    time.sleep_ms(wait)

def readAltitude():
    toggleOneShot()         # Toggle the OST bit causing the sensor to immediately take another reading

    # Wait for PDR bit, indicates we have new data
    counter = 0
    while( (IIC_Read(STATUS) & 0x02) == 0):
        counter = counter + 1
        if(counter > 600):
            # Error out after max of 512ms for a read
            return(-1)
        time.sleep_ms(1)

    # Read pressure registers
    data = bytearray(3)
    counter = 0
    nBytes = 0
    while True:
        nBytes = i2c.readfrom_mem_into(MPL3115Address, OUT_P_MSB, data)
        if nBytes == 3:
            break
        counter = counter + 1
        if(counter > 500):
            # Error out after max of 512ms for a read
            return(0x00)
        time.sleep_ms(1)            # wait 1msec

    msb = data[0]
    csb = data[1]
    lsb = data[2]

    value = (msb << 16) | (csb << 8) | lsb
    value = value >> 4
    Height = float(value) / 16.0
    return(Height)

def cylon(*, start=0, end=0, colors=(b'\xff\x22\x33\x40',), sleep_ms=250,
          verbose=False):
  """All this has happened before and all this will happen again."""
  assert len(colors) in (1,2), 'only 1 or 2 colors allowed'
  end = _default_num_leds(end)
  byte_end = end*4
  byte_start = start*4
  direction = 4
  pos = byte_start
  led_data = bytearray(led_off*end)
  while True:
    led_data[pos:pos+4] = colors[0]
    if len(colors) > 1:
      led_data[byte_end-pos-4:byte_end-pos] = colors[1]
    test(led_data, num_leds=end, rotate=0)
    if verbose:
      print('LED #', pos//4)
    time.sleep_ms(sleep_ms)
    led_data[pos:pos+4] = led_off
    if len(colors) > 1:
      led_data[byte_end-pos-4:byte_end-pos] = led_off
    pos += direction
    if pos >= byte_end or pos < byte_start:
      direction = -direction
      pos += direction*2  # Undo and go back.

def test_main():
    """Test function for verifying basic functionality."""
    print("Running test_main")
    i2c = I2C(scl=Pin(5), sda=Pin(4), freq=400000)
    lcd = I2cLcd(i2c, DEFAULT_I2C_ADDR, 2, 16)
    lcd.putstr("It Works!\nSecond Line")
    sleep_ms(3000)
    lcd.clear()
    count = 0
    while True:
        lcd.move_to(0, 0)
        lcd.putstr("%7d" % (ticks_ms() // 1000))
        sleep_ms(1000)
        count += 1
        if count % 10 == 3:
            print("Turning backlight off")
            lcd.backlight_off()
        if count % 10 == 4:
            print("Turning backlight on")
            lcd.backlight_on()
        if count % 10 == 5:
            print("Turning display off")
            lcd.display_off()
        if count % 10 == 6:
            print("Turning display on")
            lcd.display_on()
        if count % 10 == 7:
            print("Turning display & backlight off")
            lcd.backlight_off()
            lcd.display_off()
        if count % 10 == 8:
            print("Turning display & backlight on")
            lcd.backlight_on()
            lcd.display_on()

def knight_rider(loop=100, delay=50):
    """ Show Knight Rider animation
    loop = number of loops
    delay = sleep time between steps
    based on sin function
    """
    periods = 16

    # syncrhonize the two cos waves
    # this math is based on measurements vs. understanding what's going on
    np_div = np.n / 3.3

    t = 0
    for i in range(0, loop):
        t += 1
        for p in range(0, np.n):

            # this controls speed - higher is faster
            f = t * 3.2

            v1 = math.cos(f / periods + p/np_div) - 0.7
            v1 = max(0, v1)

            v2 = math.cos(-f / periods + p/np_div) - 0.7
            v2 = max(0, v2)

            b = int(v1 * 50) + int(v2 * 50)

            np[p] = (b, 0, 0)

        np.write()
        time.sleep_ms(delay)

 def _raw_temp_humi(self, temp_acc=RES_14_BIT, humi_acc=RES_14_BIT):
     """
     Initiate a temperature and humidity sensor reading in one operation. 
     This safes time (and thereby energy). Accuracy for both sensors can 
     be specified. Same valid accuracy values apply to both seonsors.
     """
     if not temp_acc in (RES_11_BIT, RES_14_BIT):
         raise ValueError('Temperature measure accuracy invalid!')
     if not temp_acc in (RES_8_BIT, RES_11_BIT, RES_14_BIT):
         raise ValueError('Humidity measure accuracy invalid!')
     config = C_MODE_BOTH
     if temp_acc == RES_11_BIT:
         config = config | C_TEMP_11BIT
     elif temp_acc == RES_14_BIT:
         config = config | C_TEMP_14BIT
     if humi_acc == RES_8_BIT:
         config = config | C_HUMI_8BIT
     elif humi_acc == RES_11_BIT:
         config = config | C_HUMI_11BIT
     elif humi_acc == RES_14_BIT:
         config = config | C_HUMI_14BIT
     self._config(config)
     self._send(R_TEMP)
     sleep_ms(20)
     raw = self._recv(4)
     return (raw[1] + (raw[0] << 8), raw[3] + (raw[2] << 8))