C++ LSDRaster::remove_positive_hilltop_curvature方法代码示例

//.........这里部分代码省略.........
    raster_selection.push_back(0);
    raster_selection.push_back(0);

    int CurrentWindowSize = window_radius;

    vector<LSDRaster> Surfaces = FilledDEM.calculate_polyfit_surface_metrics(CurrentWindowSize, raster_selection);
    LSDRaster slope = Surfaces[1];
    LSDRaster aspect = Surfaces[2];

    cout << "\nGetting drainage network and basins\n" << endl;

    // get a flow info object
  	LSDFlowInfo FlowInfo(BoundaryConditions,FilledDEM);

    //get stream net from channel heads
    stringstream ss_ch;
    ss_ch << Path << "Pelletier/" << Prefix << "_" << Resolutions[a] << "_CH";

    vector<int> sources = FlowInfo.Ingest_Channel_Heads(ss_ch.str(), "bil");
    LSDJunctionNetwork ChanNetwork(sources, FlowInfo);
    LSDIndexRaster StreamNetwork = ChanNetwork.StreamOrderArray_to_LSDIndexRaster();

    //Extract basins based on input stream order
    vector< int > basin_junctions = ChanNetwork.ExtractBasinJunctionOrder(BasinOrder, FlowInfo);
    LSDIndexRaster Basin_Raster = ChanNetwork.extract_basins_from_junction_vector(basin_junctions, FlowInfo);

    cout << "\nExtracting hilltops and hilltop curvature" << endl;

    // extract hilltops - no critical slope filtering is performed here
    LSDRaster hilltops = ChanNetwork.ExtractRidges(FlowInfo);

    //get hilltop curvature using filter to remove positive curvatures
    LSDRaster cht_raster = FilledDEM.get_hilltop_curvature(Surfaces[3], hilltops);
    LSDRaster CHT = FilledDEM.remove_positive_hilltop_curvature(cht_raster);

    cout << "Starting hilltop flow routing\n" << endl;

    // these params do not need changed during normal use of the HFR algorithm
    bool print_paths_switch = false;
    int thinning = 1;
    string trace_path = "";
    bool basin_filter_switch = false;
    vector<int> Target_Basin_Vector;

    //run HFR
    vector< Array2D<float> > HFR_Arrays = FlowInfo.HilltopFlowRouting(FilledDEM, hilltops, slope, StreamNetwork, aspect, Filename_variable, Basin_Raster, Surfaces[4], print_paths_switch, thinning, trace_path, basin_filter_switch, Target_Basin_Vector);

    LSDRaster HFR_LH = hilltops.LSDRasterTemplate(HFR_Arrays[1]);
    LSDRaster relief = hilltops.LSDRasterTemplate(HFR_Arrays[3]);

    //Filter Relief and LH data to remove any values < 2 pixels, as in Grieve et al (2015)
    LSDRaster LH1 = HFR_LH.RemoveBelow(2.0*Resolutions[a]);
    LSDRaster Relief1 = relief.RemoveBelow(2.0*Resolutions[a]);

    //Filter Relief and LH data to remove any values > 10000
    //These are created due to using 1m channel heads on low res data, and inadvertantly
    //sampling nodata values, which gives us massive relief values
    LSDRaster LH = LH1.RemoveAbove(10000);
    LSDRaster Relief = Relief1.RemoveAbove(10000);

    //go through the lh raster and get every value into a 1D vector
    vector<float> LH_vec = Flatten_Without_Nodata(LH.get_RasterData(), LH.get_NoDataValue());
    vector<float> Boxplot = BoxPlot(LH_vec);

    //write the values to the output file
    WriteLHData << Resolutions[a] << " " << Boxplot[0] << " " << Boxplot[1] << " " << Boxplot[2] << " " << Boxplot[3] << " " << Boxplot[4] << " " << Boxplot[5] << " " << Boxplot[6] << " " << Boxplot[7];

int main (int nNumberofArgs,char *argv[])
{
  
  //Test for correct input arguments
	if (nNumberofArgs!=7)
	{
		cout << "FATAL ERROR: wrong number of inputs. The program needs the path (with trailing slash), the filename prefix, window radius, "; 
    cout << "basin order, a switch to use or exclude floodplains and a switch to write rasters if desired." << endl;
		exit(EXIT_SUCCESS);
	}
  
  //load input arguments
  string path = argv[1];
	string filename = argv[2];
  float window_radius = atof(argv[3]); //6
  int BasinOrder = atoi(argv[4]);  //2
  int FloodplainSwitch = atoi(argv[5]);
  int WriteRasters = atoi(argv[6]);  //0 (do not write rasters) or 1 (write rasters) 
  
  //set boundary conditions
  vector<string> BoundaryConditions(4, "No Flux");

  //load dem
  LSDRaster DEM((path+filename+"_dem"), "flt");  
  
  //Fill 
  float MinSlope = 0.0001;
  LSDRaster FilledDEM = DEM.fill(MinSlope);
  
  //surface fitting
  vector<int> raster_selection;
  
  raster_selection.push_back(0);
  raster_selection.push_back(1); //slope 
  raster_selection.push_back(1); //aspect
  raster_selection.push_back(1); //curvature
  raster_selection.push_back(1); //plan curvature
  raster_selection.push_back(0); 
  raster_selection.push_back(0);
  raster_selection.push_back(0);

  vector<LSDRaster> Surfaces = FilledDEM.calculate_polyfit_surface_metrics(window_radius, raster_selection);
  LSDRaster slope = Surfaces[1];
  LSDRaster aspect = Surfaces[2];   
  
  cout << "\nGetting drainage network and basins\n" << endl;

  // get a flow info object
	LSDFlowInfo FlowInfo(BoundaryConditions,FilledDEM);
  
  //get stream net from channel heads
  vector<int> sources = FlowInfo.Ingest_Channel_Heads((path+filename+"_dem_CH"), "flt"); //swap to csv? 
  LSDJunctionNetwork ChanNetwork(sources, FlowInfo);
  LSDIndexRaster StreamNetwork = ChanNetwork.StreamOrderArray_to_LSDIndexRaster();

  //load floodplain and merge with the channel network if required, otherwise the 
  //floodplain mask will only contain the channel data
  LSDIndexRaster ChannelAndFloodplain;

  if (FloodplainSwitch == 1){
    LSDIndexRaster Floodplains((path+filename+"_FloodPlain"), "flt");
    ChannelAndFloodplain = StreamNetwork.MergeChannelWithFloodplain(Floodplains);
  }
  else{
    ChannelAndFloodplain = StreamNetwork;
  }
                                                         
  //Extract basins based on input stream order
  vector< int > basin_junctions = ChanNetwork.ExtractBasinJunctionOrder(BasinOrder, FlowInfo);
  LSDIndexRaster Basin_Raster = ChanNetwork.extract_basins_from_junction_vector(basin_junctions, FlowInfo);
  
  cout << "\nExtracting hilltops and hilltop curvature" << endl;
  
  // extract hilltops - no critical slope filtering is performed here
  LSDRaster hilltops = ChanNetwork.ExtractRidges(FlowInfo);   
     
  //get hilltop curvature using filter to remove positive curvatures         
  LSDRaster cht_raster = FilledDEM.get_hilltop_curvature(Surfaces[3], hilltops);
  LSDRaster CHT = FilledDEM.remove_positive_hilltop_curvature(cht_raster);  
  
  //get d infinity flowdirection and flow area
  Array2D<float> dinf = FilledDEM.D_inf_FlowDir();
  LSDRaster dinf_rast = FilledDEM.LSDRasterTemplate(dinf);
  LSDRaster DinfArea = FilledDEM.D_inf_units();
  
  cout << "Starting hilltop flow routing\n" << endl;
  
  //start of Hilltop flow routing
  string prefix = (path+filename+"_dreich_");  //set a path to write the hillslope length data to, based on the input path and filename given by the user
  
  // these params do not need changed during normal use of the HFR algorithm
  bool print_paths_switch = false;
  int thinning = 1;
  string trace_path = "";
  bool basin_filter_switch = false;                          
  vector<int> Target_Basin_Vector;

  //run HFR    
  vector< Array2D<float> > HFR_Arrays = FlowInfo.HilltopFlowRouting(FilledDEM, hilltops, slope, ChannelAndFloodplain, aspect, prefix, Basin_Raster, Surfaces[4], print_paths_switch, thinning, trace_path, basin_filter_switch, Target_Basin_Vector);
   
//.........这里部分代码省略.........

int main(int nNumberofArgs, char *argv[])
{
  //Test for correct input arguments
	if (nNumberofArgs!=5)
	{
		cout << "FATAL ERROR: wrong number of inputs. The program needs the path (with trailing slash), the filename prefix, the DEM file format, the window size in spatial units.";
		exit(EXIT_FAILURE);
	}

  //get input args
  string path = argv[1];
  string Prefix = argv[2];
  string DEM_Format = argv[3];
  int WindowSize = atoi(argv[4]);

  //surface fitting
  vector<int> raster_selection;
  raster_selection.push_back(0);
  raster_selection.push_back(1); //slope
  raster_selection.push_back(0);
	raster_selection.push_back(1); //curvature

  //set up a writer to write the output data
  ofstream WriteData;

  //create an output filename based on the dem name
  stringstream ss;

  ss << path << Prefix << "_ChtResData.txt";
  WriteData.open(ss.str().c_str());

  //write headers
  WriteData << "resoulution 2pc 25pc median mean 75pc 98pc minimum maximum" << endl;

  //array of resolutions to load
  int Resolutions[] = {1, 2, 3, 4, 5, 6, 7, 8, 9, 10};

  // vectors to hold the stats about the fitted surface
  vector<float> Curv_vec;

	//set boundary conditions
  vector<string> BoundaryConditions(4, "No Flux");

  for (int a = 0; a < 10; ++a){

	  cout << "Processing DEM " << a+1 << " of " << "10" << endl;

		//load the DEM
    //build the string of the filename to load
		stringstream ss2;
		ss2 << path << Prefix << "_" << Resolutions[a] << "_DEM";
		LSDRaster DEM(ss2.str(), DEM_Format);

		//Fill
		float MinSlope = 0.0001;
		LSDRaster FilledDEM = DEM.fill(MinSlope);

	  int CurrentWindowSize = WindowSize;
	  vector<LSDRaster> Surfaces = FilledDEM.calculate_polyfit_surface_metrics(CurrentWindowSize, raster_selection);

		// get a flow info object
	  LSDFlowInfo FlowInfo(BoundaryConditions,FilledDEM);

	  //get stream net from channel heads
	  vector<int> sources = FlowInfo.Ingest_Channel_Heads((path+Prefix+"_CH"), "csv", 2);

	  LSDJunctionNetwork ChanNetwork(sources, FlowInfo);

		// extract hilltops
    LSDRaster hilltops = ChanNetwork.ExtractRidges(FlowInfo);
    LSDRaster Hilltops = ChanNetwork.ExtractHilltops(hilltops, Surfaces[1], 0.4);


    //get hilltop curvature using filter to remove positive curvatures
    LSDRaster cht_raster = FilledDEM.get_hilltop_curvature(Surfaces[3], Hilltops);
    LSDRaster CHT = FilledDEM.remove_positive_hilltop_curvature(cht_raster);

	  //go through the landscape and get every curvature value into a 1D vector
    Curv_vec = Flatten_Without_Nodata(CHT.get_RasterData(), CHT.get_NoDataValue());

    stringstream ss3;
    ss3 << path << Prefix << "_" << Resolutions[a] << "_Hist_CHT.txt";

    print_histogram(Curv_vec, 0.01, ss3.str());

    vector<float> Boxplot = BoxPlot(Curv_vec);

	  //write the values to the output file
	  WriteData << Resolutions[a] << " " << Boxplot[0] << " " << Boxplot[1] << " " << Boxplot[2] << " " << Boxplot[3] << " " << Boxplot[4] << " " << Boxplot[5] << " " << Boxplot[6] << " " << Boxplot[7];

		WriteData << endl;

  }
  WriteData.close();

}