C++ KVDetector::IsCalibrated方法代码示例

void KVIDTelescope::CalculateParticleEnergy(KVReconstructedNucleus* nuc)
{
   // The energy of each particle is calculated as follows:
   //
   //      E = dE_1 + dE_2 + ... + dE_N
   //
   // dE_1, dE_2, ... = energy losses measured in each detector through which
   //                          the particle has passed (or stopped, in the case of dE_N).
   //                         These energy losses are corrected for (Z,A)-dependent effects
   //                          such as pulse-heigth defect in silicon detectors, losses in
   //                          windows of gas detectors, etc.
   //
   // Whenever possible, the energy loss for fired detectors which are uncalibrated
   // or not functioning is calculated. In this case the status returned by GetCalibStatus()
   // will be KVIDTelescope::kCalibStatus_Calculated.
   // If none of the detectors is calibrated, the particle's energy cannot be calculated &
   // the status will be KVIDTelescope::kCalibStatus_NoCalibrations.
   // Otherwise, the status code will be KVIDTelescope::kCalibStatus_OK.

   //status code
   fCalibStatus = kCalibStatus_NoCalibrations;

   UInt_t z = nuc->GetZ();
   //uncharged particles
   if (z == 0) return;

   KVDetector* d1 = GetDetector(1);
   KVDetector* d2 = (fDetectors->GetSize() > 1 ? GetDetector(2) : 0);
   Bool_t d1_cal = d1->IsCalibrated();
   Bool_t d2_cal = (d2 ? d2->IsCalibrated() : kFALSE);

   //no calibrations
   if (!d1_cal && !d2)
      return;
   if ((d1 && d2) && !d1_cal && !d2_cal)
      return;

   //status code
   fCalibStatus = kCalibStatus_OK;

   UInt_t a = nuc->GetA();

   // particles stopped in first member of telescope
   if (nuc->GetStatus() == 3) {
      if (d1_cal) {
         nuc->SetEnergy(d1->GetCorrectedEnergy(nuc, -1, kFALSE));  //N.B.: transmission=kFALSE because particle stop in d1
      }
      return;
   }

   Double_t e1, e2, einc;
   e1 = e2 = einc = 0.0;

   if (!d1_cal) {//1st detector not calibrated - calculate from residual energy in 2nd detector

      //second detector must exist and have all acquisition parameters fired with above-pedestal value
      if (d2 && d2->Fired("Pall")) e2 = d2->GetCorrectedEnergy(nuc, -1, kFALSE); //N.B.: transmission=kFALSE because particle stop in d2
      if (e2 <= 0.0) {
         // zero energy loss in 2nd detector ? can't do anything...
         fCalibStatus = kCalibStatus_NoCalibrations;
         return;
      }
      //calculate & set energy loss in dE detector
      //N.B. using e2 for the residual energy after detector 1 means
      //that we are assuming the particle stops in detector 2.
      //if this is not true, we will underestimate the energy of the particle.
      e1 = d1->GetDeltaEFromERes(z, a, e2);
      if (e1 < 0.0) e1 = 0.0;
      else {
         d1->SetEnergyLoss(e1);
         d1->SetEResAfterDetector(e2);
         e1 = d1->GetCorrectedEnergy(nuc);
         //status code
         fCalibStatus = kCalibStatus_Calculated;
      }
   } else {//1st detector is calibrated too: get corrected energy loss

      e1 = d1->GetCorrectedEnergy(nuc);

   }

   if (d2 && !d2_cal) {//2nd detector not calibrated - calculate from energy loss in 1st detector

      e1 = d1->GetCorrectedEnergy(nuc);
      if (e1 <= 0.0) {
         // zero energy loss in 1st detector ? can't do anything...
         fCalibStatus = kCalibStatus_NoCalibrations;
         return;
      }
      //calculate & set energy loss in 2nd detector
      e2 = d1->GetEResFromDeltaE(z, a);
      if (e2 < 0.0) e2 = 0.0;
      else {
         e2 = d2->GetDeltaE(z, a, e2);
         d2->SetEnergyLoss(e2);
         e2 = d2->GetCorrectedEnergy(nuc);
         //status code
         fCalibStatus = kCalibStatus_Calculated;
      }
   } else if (d2) { //2nd detector is calibrated too: get corrected energy loss
//.........这里部分代码省略.........