当前位置: 首页>>代码示例>>C++>>正文

C++ sirdev_set_dtr_rts函数代码示例

本文整理汇总了C++中sirdev_set_dtr_rts函数的典型用法代码示例。如果您正苦于以下问题：C++ sirdev_set_dtr_rts函数的具体用法？C++ sirdev_set_dtr_rts怎么用？C++ sirdev_set_dtr_rts使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。


在下文中一共展示了sirdev_set_dtr_rts函数的15个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于系统推荐出更棒的C++代码示例。

示例1: litelink_reset

/*
 * Function litelink_reset (task)
 *
 *      Reset the Litelink type dongle.
 *
 */
static int litelink_reset(struct sir_dev *dev)
{
	IRDA_DEBUG(2, "%s()\n", __func__);

	/* probably the power-up can be dropped here, but with only
	 * 15 usec delay it's not worth the risk unless somebody with
	 * the hardware confirms it doesn't break anything...
	 */

	/* Power on dongle */
	sirdev_set_dtr_rts(dev, TRUE, TRUE);

	/* Sleep a minimum of 15 us */
	udelay(MIN_DELAY);

	/* Clear RTS to reset dongle */
	sirdev_set_dtr_rts(dev, TRUE, FALSE);

	/* Sleep a minimum of 15 us */
	udelay(MIN_DELAY);

	/* Go back to normal mode */
	sirdev_set_dtr_rts(dev, TRUE, TRUE);

	/* Sleep a minimum of 15 us */
	udelay(MIN_DELAY);

	dev->speed = 115200;

	return 0;
}
开发者ID:magnusjjj，项目名称:android_kernel_huawei_rle，代码行数:37，代码来源:litelink-sir.c

示例2: actisys_reset

static int actisys_reset(struct sir_dev *dev)
{
	/* Reset the dongle : set DTR low for 10 us */
	sirdev_set_dtr_rts(dev, FALSE, TRUE);
	udelay(MIN_DELAY);

	/* Go back to normal mode */
	sirdev_set_dtr_rts(dev, TRUE, TRUE);
	
	dev->speed = 9600;	/* That's the default */

	return 0;
}
开发者ID:3sOx，项目名称:asuswrt-merlin，代码行数:13，代码来源:actisys-sir.c

示例3: ma600_change_speed

static int ma600_change_speed(struct sir_dev *dev, unsigned speed)
{
	u8	byte;
	
	IRDA_DEBUG(2, "%s(), speed=%d (was %d)\n", __FUNCTION__,
		speed, dev->speed);

	/* dongle already reset, dongle and port at default speed (9600) */

	/* Set RTS low for 1 ms */
	sirdev_set_dtr_rts(dev, TRUE, FALSE);
	mdelay(1);

	/* Write control byte */
	byte = get_control_byte(speed);
	sirdev_raw_write(dev, &byte, sizeof(byte));

	/* Wait at least 10ms: fake wait_until_sent - 10 bits at 9600 baud*/
	set_current_state(TASK_UNINTERRUPTIBLE);
	schedule_timeout(msecs_to_jiffies(15));		/* old ma600 uses 15ms */

#if 1
	/* read-back of the control byte. ma600 is the first dongle driver
	 * which uses this so there might be some unidentified issues.
	 * Disable this in case of problems with readback.
	 */

	sirdev_raw_read(dev, &byte, sizeof(byte));
	if (byte != get_control_byte(speed))  {
		WARNING("%s(): bad control byte read-back %02x != %02x\n",
			__FUNCTION__, (unsigned) byte,
			(unsigned) get_control_byte(speed));
		return -1;
	}
	else
		IRDA_DEBUG(2, "%s() control byte write read OK\n", __FUNCTION__);
#endif

	/* Set DTR, Set RTS */
	sirdev_set_dtr_rts(dev, TRUE, TRUE);

	/* Wait at least 10ms */
	set_current_state(TASK_UNINTERRUPTIBLE);
	schedule_timeout(msecs_to_jiffies(10));

	/* dongle is now switched to the new speed */
	dev->speed = speed;

	return 0;
}
开发者ID:Antonio-Zhou，项目名称:Linux-2.6.11，代码行数:50，代码来源:ma600-sir.c

示例4: ma600_reset

int ma600_reset(struct sir_dev *dev)
{
	IRDA_DEBUG(2, "%s()\n", __func__);

	/* Reset the dongle : set DTR low for 10 ms */
	sirdev_set_dtr_rts(dev, FALSE, TRUE);
	msleep(10);

	/* Go back to normal mode */
	sirdev_set_dtr_rts(dev, TRUE, TRUE);
	msleep(10);

	dev->speed = 9600;      /* That's the dongle-default */

	return 0;
}
开发者ID:E-LLP，项目名称:n900，代码行数:16，代码来源:ma600-sir.c

示例5: toim3232_close

static int toim3232_close(struct sir_dev *dev)
{
	/* Power off dongle */
	sirdev_set_dtr_rts(dev, FALSE, FALSE);

	return 0;
}
开发者ID:020gzh，项目名称:linux，代码行数:7，代码来源:toim3232-sir.c

示例6: actisys_close

static int actisys_close(struct sir_dev *dev)
{
	/* Power off the dongle */
	sirdev_set_dtr_rts(dev, FALSE, FALSE);

	return 0;
}
开发者ID:3sOx，项目名称:asuswrt-merlin，代码行数:7，代码来源:actisys-sir.c

示例7: girbil_reset

static int girbil_reset(struct sir_dev *dev)
{
    unsigned state = dev->fsm.substate;
    unsigned delay = 0;
    u8 control = GIRBIL_TXEN | GIRBIL_RXEN;
    int ret = 0;

    IRDA_DEBUG(2, "%s()\n", __FUNCTION__);

    switch (state) {
    case SIRDEV_STATE_DONGLE_RESET:
        /* Reset dongle */
        sirdev_set_dtr_rts(dev, TRUE, FALSE);
        /* Sleep at least 5 ms */
        delay = 20;
        state = GIRBIL_STATE_WAIT1_RESET;
        break;

    case GIRBIL_STATE_WAIT1_RESET:
        /* Set DTR and clear RTS to enter command mode */
        sirdev_set_dtr_rts(dev, FALSE, TRUE);
        delay = 20;
        state = GIRBIL_STATE_WAIT2_RESET;
        break;

    case GIRBIL_STATE_WAIT2_RESET:
        /* Write control byte */
        sirdev_raw_write(dev, &control, 1);
        delay = 20;
        state = GIRBIL_STATE_WAIT3_RESET;
        break;

    case GIRBIL_STATE_WAIT3_RESET:
        /* Go back to normal mode */
        sirdev_set_dtr_rts(dev, TRUE, TRUE);
        dev->speed = 9600;
        break;

    default:
        IRDA_ERROR("%s(), undefined state %d\n", __FUNCTION__, state);
        ret = -1;
        break;
    }
    dev->fsm.substate = state;
    return (delay > 0) ? delay : ret;
}
开发者ID:274914765，项目名称:C，代码行数:46，代码来源:girbil-sir.c

示例8: tekram_reset

static int tekram_reset(struct sir_dev *dev)
{
	/* Clear DTR, Set RTS */
	sirdev_set_dtr_rts(dev, FALSE, TRUE); 

	/* Should sleep 1 ms */
	msleep(1);

	/* Set DTR, Set RTS */
	sirdev_set_dtr_rts(dev, TRUE, TRUE);
	
	/* Wait at least 50 us */
	udelay(75);

	dev->speed = 9600;

	return 0;
}
开发者ID:020gzh，项目名称:linux，代码行数:18，代码来源:tekram-sir.c

示例9: tekram_close

static int tekram_close(struct sir_dev *dev)
{
	IRDA_DEBUG(2, "%s()\n", __func__);

	/*                  */
	sirdev_set_dtr_rts(dev, FALSE, FALSE);

	return 0;
}
开发者ID:romanbb，项目名称:android_kernel_lge_d851，代码行数:9，代码来源:tekram-sir.c

示例10: girbil_close

static int girbil_close(struct sir_dev *dev)
{
    IRDA_DEBUG(2, "%s()\n", __FUNCTION__);

    /* Power off dongle */
    sirdev_set_dtr_rts(dev, FALSE, FALSE);

    return 0;
}
开发者ID:274914765，项目名称:C，代码行数:9，代码来源:girbil-sir.c

示例11: ma600_reset

int ma600_reset(struct sir_dev *dev)
{
	IRDA_DEBUG(2, "%s()\n", __FUNCTION__);

	/* Reset the dongle : set DTR low for 10 ms */
	sirdev_set_dtr_rts(dev, FALSE, TRUE);
	set_current_state(TASK_UNINTERRUPTIBLE);
	schedule_timeout(msecs_to_jiffies(10));

	/* Go back to normal mode */
	sirdev_set_dtr_rts(dev, TRUE, TRUE);
	set_current_state(TASK_UNINTERRUPTIBLE);
	schedule_timeout(msecs_to_jiffies(10));

	dev->speed = 9600;      /* That's the dongle-default */

	return 0;
}
开发者ID:Antonio-Zhou，项目名称:Linux-2.6.11，代码行数:18，代码来源:ma600-sir.c

示例12: tekram_reset

static int tekram_reset(struct sir_dev *dev)
{
	IRDA_DEBUG(2, "%s()\n", __func__);

	
	sirdev_set_dtr_rts(dev, FALSE, TRUE); 

	
	msleep(1);

	
	sirdev_set_dtr_rts(dev, TRUE, TRUE);
	
	
	udelay(75);

	dev->speed = 9600;

	return 0;
}
开发者ID:DirtyDroidX，项目名称:android_kernel_htc_m8ul，代码行数:20，代码来源:tekram-sir.c

示例13: mcp2120_close

static int mcp2120_close(struct sir_dev *dev)
{
	IRDA_DEBUG(2, "%s()\n", __func__);

	/* Power off dongle */
        /* reset and inhibit mcp2120 */
	sirdev_set_dtr_rts(dev, TRUE, TRUE);
	// sirdev_set_dtr_rts(dev, FALSE, FALSE);

	return 0;
}
开发者ID:nos1609，项目名称:Chrono_Kernel-1，代码行数:11，代码来源:mcp2120-sir.c

示例14: tekram_reset

static int tekram_reset(struct sir_dev *dev)
{
	IRDA_DEBUG(2, "%s()\n", __FUNCTION__);

	/* Clear DTR, Set RTS */
	sirdev_set_dtr_rts(dev, FALSE, TRUE); 

	/* Should sleep 1 ms */
	set_current_state(TASK_UNINTERRUPTIBLE);
	schedule_timeout(MSECS_TO_JIFFIES(1));

	/* Set DTR, Set RTS */
	sirdev_set_dtr_rts(dev, TRUE, TRUE);
	
	/* Wait at least 50 us */
	udelay(75);

	dev->speed = 9600;

	return 0;
}
开发者ID:wxlong，项目名称:Test，代码行数:21，代码来源:tekram-sir.c

示例15: toim3232_reset

static int toim3232_reset(struct sir_dev *dev)
{
	/* Switch off both DTR and RTS to switch off dongle */
	sirdev_set_dtr_rts(dev, FALSE, FALSE);

	/* Should sleep a while. This might be evil doing it this way.*/
	set_current_state(TASK_UNINTERRUPTIBLE);
	schedule_timeout(msecs_to_jiffies(50));

	/* Set DTR, Set RTS (data mode) */
	sirdev_set_dtr_rts(dev, TRUE, TRUE);

	/* Wait at least 10 ms for power to stabilize again */
	set_current_state(TASK_UNINTERRUPTIBLE);
	schedule_timeout(msecs_to_jiffies(10));

	/* Speed should now be 9600 */
	dev->speed = 9600;

	return 0;
}
开发者ID:020gzh，项目名称:linux，代码行数:21，代码来源:toim3232-sir.c


注：本文中的sirdev_set_dtr_rts函数示例由纯净天空整理自Github/MSDocs等开源代码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。