C++ set_sysinfo_in_ram函数代码示例

void cache_as_ram_new_stack (void)
{
	void *resume_backup_memory = NULL;

	print_car_debug("Top about %08x ... Done\n", (uint32_t) &resume_backup_memory);
	print_car_debug("Disabling cache as ram now\n");
	disable_cache_as_ram_bsp();

	disable_cache();
	/* Enable cached access to RAM in the range 1M to CONFIG_RAMTOP */
	set_var_mtrr(0, 0x00000000, CONFIG_RAMTOP, MTRR_TYPE_WRBACK);
	enable_cache();

	if (acpi_is_wakeup_s3()) {
		resume_backup_memory = cbmem_find(CBMEM_ID_RESUME);
		print_car_debug("Resume backup memory location: %p\n", resume_backup_memory);
	}
	prepare_ramstage_region(resume_backup_memory);

	set_sysinfo_in_ram(1); // So other core0 could start to train mem

	/*copy and execute ramstage */
	copy_and_run();
	/* We will not return */

	print_car_debug("should not be here -\n");
}

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	struct sys_info *sysinfo = &sysinfo_car;

	u32 bsp_apicid = 0, val, wants_reset;
	msr_t msr;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		set_bsp_node_CHtExtNodeCfgEn();
		enumerate_ht_chain();
		sio_setup();
	}

	post_code(0x30);

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	post_code(0x32);

	winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	val = cpuid_eax(1);
	printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
	printk(BIOS_DEBUG, "bsp_apicid = %02x\n", bsp_apicid);
	printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);

	/* Setup sysinfo defaults */
	set_sysinfo_in_ram(0);

	update_microcode(val);

	post_code(0x33);

	cpuSetAMDMSR();
	post_code(0x34);

	amd_ht_init(sysinfo);
	post_code(0x35);

	/* Setup nodes PCI space and start core 0 AP init. */
	finalize_node_setup(sysinfo);

	/* Setup any mainboard PCI settings etc. */
	setup_mb_resource_map();
	post_code(0x36);

	/* wait for all the APs core0 started by finalize_node_setup. */
	/* FIXME: A bunch of cores are going to start output to serial at once.
	 * It would be nice to fixup prink spinlocks for ROM XIP mode.
	 * I think it could be done by putting the spinlock flag in the cache
	 * of the BSP located right after sysinfo.
	 */
	wait_all_core0_started();

#if CONFIG_LOGICAL_CPUS
	/* Core0 on each node is configured. Now setup any additional cores. */
	printk(BIOS_DEBUG, "start_other_cores()\n");
	start_other_cores();
	post_code(0x37);
	wait_all_other_cores_started(bsp_apicid);
#endif

	post_code(0x38);

#if CONFIG_SET_FIDVID
	msr = rdmsr(0xc0010071);
	printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);

	/* FIXME: The sb fid change may survive the warm reset and only
	 * need to be done once.*/
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);

	post_code(0x39);

	if (!warm_reset_detect(0)) {			// BSP is node 0
		init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
	} else {
		init_fidvid_stage2(bsp_apicid, 0);	// BSP is node 0
	}

	post_code(0x3A);

	/* show final fid and vid */
	msr=rdmsr(0xc0010071);
	printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);
#endif

	init_timer(); // Need to use TMICT to synconize FID/VID

	wants_reset = mcp55_early_setup_x();

	/* Reset for HT, FIDVID, PLL and errata changes to take affect. */
//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	struct sys_info *sysinfo = &sysinfo_car;
	static const u8 spd_addr[] = {RC00, DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0, };
	u32 bsp_apicid = 0, val;
	msr_t msr;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		/* mov bsp to bus 0xff when > 8 nodes */
		set_bsp_node_CHtExtNodeCfgEn();
		enumerate_ht_chain();
		sb7xx_51xx_pci_port80();
	}

	post_code(0x30);

	if (bist == 0) {
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); /* mmconf is inited in init_cpus */
		/* All cores run this but the BSP(node0,core0) is the only core that returns. */
	}

	post_code(0x32);

	enable_rs780_dev8();
	sb7xx_51xx_lpc_init();

	ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	ite_kill_watchdog(GPIO_DEV);

	console_init();

//	dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	// Load MPB
	val = cpuid_eax(1);
	printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
	printk(BIOS_DEBUG, "bsp_apicid = %02x \n", bsp_apicid);
	printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);

	/* Setup sysinfo defaults */
	set_sysinfo_in_ram(0);

	update_microcode(val);

	post_code(0x33);

	cpuSetAMDMSR();
	post_code(0x34);

	amd_ht_init(sysinfo);
	post_code(0x35);

	/* Setup nodes PCI space and start core 0 AP init. */
	finalize_node_setup(sysinfo);

	/* Setup any mainboard PCI settings etc. */
	setup_mb_resource_map();
	post_code(0x36);

	/* wait for all the APs core0 started by finalize_node_setup. */
	/* FIXME: A bunch of cores are going to start output to serial at once.
	   It would be nice to fixup prink spinlocks for ROM XIP mode.
	   I think it could be done by putting the spinlock flag in the cache
	   of the BSP located right after sysinfo.
	 */
	wait_all_core0_started();

 #if CONFIG_LOGICAL_CPUS
	/* Core0 on each node is configured. Now setup any additional cores. */
	printk(BIOS_DEBUG, "start_other_cores()\n");
	start_other_cores();
	post_code(0x37);
	wait_all_other_cores_started(bsp_apicid);
 #endif

	post_code(0x38);

	/* run _early_setup before soft-reset. */
	rs780_early_setup();
	sb7xx_51xx_early_setup();

 #if CONFIG_SET_FIDVID
	msr = rdmsr(0xc0010071);
	printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);

	/* FIXME: The sb fid change may survive the warm reset and only
	   need to be done once.*/
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);

	post_code(0x39);

	if (!warm_reset_detect(0)) {			// BSP is node 0
		init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
	} else {
//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr [] = {
		// Node 0
		DIMM0, DIMM2, 0, 0,
		DIMM1, DIMM3, 0, 0,
		// Node 1
		DIMM4, DIMM6, 0, 0,
		DIMM5, DIMM7, 0, 0,
	};

        struct sys_info *sysinfo = &sysinfo_car;
        int needs_reset = 0;
        unsigned bsp_apicid = 0;

        if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		sio_setup();
        }

        if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

#if 0
	uint8_t tmp = 0;
	pnp_enter_ext_func_mode(SERIAL_DEV);
	/* The following line will set CLKIN to 24 MHz, external */
	pnp_write_config(SERIAL_DEV, IT8716F_CONFIG_REG_CLOCKSEL, 0x11);
	tmp = pnp_read_config(SERIAL_DEV, IT8716F_CONFIG_REG_SWSUSP);
	/* Is serial flash enabled? Then enable writing to serial flash. */
	if (tmp & 0x0e) {
		pnp_write_config(SERIAL_DEV, IT8716F_CONFIG_REG_SWSUSP, tmp | 0x10);
		pnp_set_logical_device(GPIO_DEV);
		/* Set Serial Flash interface to 0x0820 */
		pnp_write_config(GPIO_DEV, 0x64, 0x08);
		pnp_write_config(GPIO_DEV, 0x65, 0x20);
	}
 	it8716f_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
	pnp_exit_ext_func_mode(SERIAL_DEV);
#endif
	ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_48);
	ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);

        setup_mb_resource_map();

        console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);

        print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");

        set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
        setup_coherent_ht_domain(); // routing table and start other core0

        wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
        // It is said that we should start core1 after all core0 launched
        /* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
         * So here need to make sure last core0 is started, esp for two way system,
         * (there may be apic id conflicts in that case)
         */
        start_other_cores();
        wait_all_other_cores_started(bsp_apicid);
#endif

        /* it will set up chains and store link pair for optimization later */
        ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn

#if CONFIG_SET_FIDVID
        {
                msr_t msr;
                msr=rdmsr(0xc0010042);
                print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
        }
        enable_fid_change();
        enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
        init_fidvid_bsp(bsp_apicid);
        // show final fid and vid
        {
                msr_t msr;
                msr=rdmsr(0xc0010042);
                print_debug("end   msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
        }
#endif

	init_timer(); // Need to use TMICT to synconize FID/VID

        needs_reset |= optimize_link_coherent_ht();
        needs_reset |= optimize_link_incoherent_ht(sysinfo);
        needs_reset |= mcp55_early_setup_x();

        // fidvid change will issue one LDTSTOP and the HT change will be effective too
        if (needs_reset) {
                print_info("ht reset -\n");
              	soft_reset();
//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	struct sys_info *sysinfo = &sysinfo_car;
	static const u8 spd_addr[] = {RC00, DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0, };
	u32 bsp_apicid = 0, val;
	msr_t msr;

	timestamp_init(timestamp_get());
	timestamp_add_now(TS_START_ROMSTAGE);

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		/* mov bsp to bus 0xff when > 8 nodes */
		set_bsp_node_CHtExtNodeCfgEn();
		enumerate_ht_chain();

		/*enable port80 decoding and southbridge poweron init */
		sb_Poweron_Init();
	}

	post_code(0x30);

	if (bist == 0) {
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); /* mmconf is inited in init_cpus */
		/* All cores run this but the BSP(node0,core0) is the only core that returns. */
	}

	post_code(0x32);

	enable_rs780_dev8();
	sb800_clk_output_48Mhz();

	w83627hf_set_clksel_48(CLK_DEV);
	winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);

	console_init();
	printk(BIOS_DEBUG, "\n");

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	/* Load MPB */
	val = cpuid_eax(1);
	printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
	printk(BIOS_DEBUG, "bsp_apicid = %02x\n", bsp_apicid);
	printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);

	/* Setup sysinfo defaults */
	set_sysinfo_in_ram(0);

	update_microcode(val);

	post_code(0x33);

	cpuSetAMDMSR(0);
	post_code(0x34);

	amd_ht_init(sysinfo);
	post_code(0x35);

	/* Setup nodes PCI space and start core 0 AP init. */
	finalize_node_setup(sysinfo);

	/* Setup any mainboard PCI settings etc. */
	setup_mb_resource_map();
	post_code(0x36);

	/* wait for all the APs core0 started by finalize_node_setup. */
	/* FIXME: A bunch of cores are going to start output to serial at once.
	   It would be nice to fixup prink spinlocks for ROM XIP mode.
	   I think it could be done by putting the spinlock flag in the cache
	   of the BSP located right after sysinfo.
	 */
	wait_all_core0_started();

#if CONFIG_LOGICAL_CPUS
	/* Core0 on each node is configured. Now setup any additional cores. */
	printk(BIOS_DEBUG, "start_other_cores()\n");
	start_other_cores(bsp_apicid);
	post_code(0x37);
	wait_all_other_cores_started(bsp_apicid);
#endif

	post_code(0x38);

	/* run _early_setup before soft-reset. */
	rs780_early_setup();

#if CONFIG_SET_FIDVID
	msr = rdmsr(0xc0010071);
	printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);
	post_code(0x39);

	if (!warm_reset_detect(0)) {			/* BSP is node 0 */
		init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
	} else {
		init_fidvid_stage2(bsp_apicid, 0);	/* BSP is node 0 */
	}
//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr [] = {
			// Node 0
			(0xa<<3)|0, (0xa<<3)|2, 0, 0,
			(0xa<<3)|1, (0xa<<3)|3, 0, 0,
			// Node 1
			(0xa<<3)|4, (0xa<<3)|6, 0, 0,
			(0xa<<3)|5, (0xa<<3)|7, 0, 0,
	};

	struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE
		+ CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);

	int needs_reset = 0;
	unsigned bsp_apicid = 0;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */

		enumerate_ht_chain();

		sio_setup();

		/* Setup the mcp55 */
		mcp55_enable_rom();
	}

	if (bist == 0) {
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
	}

	w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);

	setup_mb_resource_map();

	uart_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

#if CONFIG_USBDEBUG
	mcp55_enable_usbdebug(CONFIG_USBDEBUG_DEFAULT_PORT);
	early_usbdebug_init();
#endif
	console_init();
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);

	print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");

#if CONFIG_MEM_TRAIN_SEQ == 1
	set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
	setup_coherent_ht_domain(); // routing table and start other core0

	wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS==1
	// It is said that we should start core1 after all core0 launched
	/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
	 * So here need to make sure last core0 is started, esp for two way system,
	 * (there may be apic id conflicts in that case)
	 */
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* it will set up chains and store link pair for optimization later */
	ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn

#if SET_FIDVID == 1

	{
		msr_t msr;
		msr=rdmsr(0xc0010042);
		print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");

	}

	enable_fid_change();

	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);

	init_fidvid_bsp(bsp_apicid);

	// show final fid and vid
	{
		msr_t msr;
		msr=rdmsr(0xc0010042);
		print_debug("end   msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");

	}
#endif

	init_timer(); // Need to use TMICT to synconize FID/VID

	needs_reset |= optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	needs_reset |= mcp55_early_setup_x();

//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr[] = {
		// Node 0
		DIMM0, DIMM2, 0, 0,
		DIMM1, DIMM3, 0, 0,
		// Node 1
		DIMM4, DIMM6, 0, 0,
		DIMM5, DIMM7, 0, 0,
	};

	struct sys_info *sysinfo = &sysinfo_car;
	int needs_reset = 0;
	unsigned bsp_apicid = 0;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0. */
		/* Allow the HT devices to be found. */
		enumerate_ht_chain();
		sio_setup();
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	/* FIXME: This should be part of the Super I/O code/config. */
	pnp_enter_ext_func_mode(SERIAL_DEV);
	/* Switch CLKSEL to 24MHz (default is 48MHz). Needed for serial! */
	pnp_write_config(SERIAL_DEV, 0x24, 0);
	w83627ehg_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
	pnp_exit_ext_func_mode(SERIAL_DEV);

	setup_mb_resource_map();
	console_init();
	report_bist_failure(bist); /* Halt upon BIST failure. */

	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
	print_debug("bsp_apicid=");
	print_debug_hex8(bsp_apicid);
	print_debug("\n");

#if CONFIG_MEM_TRAIN_SEQ == 1
	/* In BSP so could hold all AP until sysinfo is in RAM. */
	set_sysinfo_in_ram(0);
#endif

	setup_coherent_ht_domain(); /* Routing table and start other core0. */
	wait_all_core0_started();

#if CONFIG_LOGICAL_CPUS
	/* It is said that we should start core1 after all core0 launched
	 * becase optimize_link_coherent_ht is moved out from
	 * setup_coherent_ht_domain, so here need to make sure last core0 is
	 * started, esp for two way system (there may be APIC ID conflicts in
	 * that case).
	 */
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* Set up chains and store link pair for optimization later. */
	ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */

#if CONFIG_SET_FIDVID
	{
		msr_t msr = rdmsr(0xc0010042);
		print_debug("begin msr fid, vid ");
		print_debug_hex32(msr.hi);
		print_debug_hex32(msr.lo);
		print_debug("\n");
	}
	enable_fid_change();
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
	init_fidvid_bsp(bsp_apicid);
	{
		msr_t msr = rdmsr(0xc0010042);
		print_debug("end   msr fid, vid ");
		print_debug_hex32(msr.hi);
		print_debug_hex32(msr.lo);
		print_debug("\n");
	}
#endif

	init_timer(); /* Need to use TMICT to synconize FID/VID. */

	needs_reset |= optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	needs_reset |= mcp55_early_setup_x();

	/* fidvid change will issue one LDTSTOP and the HT change will be effective too. */
	if (needs_reset) {
		print_info("ht reset -\n");
		soft_reset();
	}
	allow_all_aps_stop(bsp_apicid);

	/* It's the time to set ctrl in sysinfo now. */
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	enable_smbus();
//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr [] = {
		// Node 0
		DIMM0, DIMM2, 0, 0,
		DIMM1, DIMM3, 0, 0,
		// Node 1
		DIMM4, DIMM6, 0, 0,
		DIMM5, DIMM7, 0, 0,
	};

	struct sys_info *sysinfo = &sysinfo_car;
	int needs_reset = 0;
	unsigned bsp_apicid = 0;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		sio_setup();
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	setup_mb_resource_map();

	dme1737_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);

	printk(BIOS_DEBUG, "bsp_apicid=%02x\n", bsp_apicid);

	set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
	setup_coherent_ht_domain(); // routing table and start other core0

	wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
	// It is said that we should start core1 after all core0 launched
	/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
	 * So here need to make sure last core0 is started, esp for two way system,
	 * (there may be apic id conflicts in that case)
	 */
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* it will set up chains and store link pair for optimization later */
	ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn

#if CONFIG_SET_FIDVID
	{
		msr_t msr;
		msr=rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "begin msr fid, vid %08x%08x\n", msr.hi, msr.lo);
	}
	enable_fid_change();
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
	init_fidvid_bsp(bsp_apicid);
	// show final fid and vid
	{
		msr_t msr;
		msr=rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "end   msr fid, vid %08x%08x\n", msr.hi, msr.lo);
	}
#endif

	init_timer(); /* Need to use TMICT to synchronize FID/VID. */

	needs_reset |= optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	needs_reset |= mcp55_early_setup_x();

	/* mask NMI from constantly-asserted-on-this-board SERR# */
	outb((inb(NMI_SC) & 0x0f) | PCI_SERR_EN, NMI_SC);

	// fidvid change will issue one LDTSTOP and the HT change will be effective too
	if (needs_reset) {
		printk(BIOS_INFO, "ht reset -\n");
		soft_reset();
	}
	allow_all_aps_stop(bsp_apicid);

	//It's the time to set ctrl in sysinfo now;
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	enable_smbus();

	/* all ap stopped? */

	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);

	post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
}

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr[] = {
			//first node
                        RC0|DIMM0, RC0|DIMM2, 0, 0,
                        RC0|DIMM1, RC0|DIMM3, 0, 0,
#if CONFIG_MAX_PHYSICAL_CPUS > 1
			//second node
                        RC1|DIMM0, RC1|DIMM2, RC1|DIMM4, RC1|DIMM6,
                        RC1|DIMM1, RC1|DIMM3, RC1|DIMM5, RC1|DIMM7,
#endif
#if CONFIG_MAX_PHYSICAL_CPUS > 2
                        // third node
                        RC2|DIMM0, RC2|DIMM2, 0, 0,
                        RC2|DIMM1, RC2|DIMM3, 0, 0,
                        // four node
                        RC3|DIMM0, RC3|DIMM2, RC3|DIMM4, RC3|DIMM6,
                        RC3|DIMM1, RC3|DIMM3, RC3|DIMM5, RC3|DIMM7,
#endif

	};

	struct sys_info *sysinfo = &sysinfo_car;
        int needs_reset;
        unsigned bsp_apicid = 0;
#if CONFIG_SET_FIDVID
	struct cpuid_result cpuid1;
#endif

        if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	console_init();

//	dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);

        setup_mb_resource_map();
#if 0
        dump_pci_device(PCI_DEV(0, 0x18, 0));
	dump_pci_device(PCI_DEV(0, 0x19, 0));
#endif

	print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");

        set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
	setup_coherent_ht_domain(); // routing table and start other core0

	wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
        // It is said that we should start core1 after all core0 launched
	/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
	 * So here need to make sure last core0 is started, esp for two way system,
	 * (there may be apic id conflicts in that case)
	 */
        start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* it will set up chains and store link pair for optimization later */
        ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn

#if 0
	//it your CPU min fid is 1G, you can change HT to 1G and FID to max one time.
        needs_reset = optimize_link_coherent_ht();
        needs_reset |= optimize_link_incoherent_ht(sysinfo);
#endif

#if CONFIG_SET_FIDVID
	/* Check to see if processor is capable of changing FIDVID  */
	/* otherwise it will throw a GP# when reading FIDVID_STATUS */
	cpuid1 = cpuid(0x80000007);
	if ((cpuid1.edx & 0x6) == 0x6) {

        {
		/* Read FIDVID_STATUS */
                msr_t msr;
                msr=rdmsr(0xc0010042);
                print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
        }

	enable_fid_change();
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
        init_fidvid_bsp(bsp_apicid);

        // show final fid and vid
        {
                msr_t msr;
                msr=rdmsr(0xc0010042);
                print_debug("end   msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
        }

	} else {
		print_debug("Changing FIDVID not supported\n");
	}
//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
/* The SPD is being read from the CPU1 (marked CPU2 on the board) and we
   don't know how to switch the SMBus to decode the CPU0 SPDs. So, The
   memory on each CPU must be an exact match.
 */
	static const uint16_t spd_addr[] = {
		// Node 0
		RC0 | DIMM0, RC0 | DIMM2,
		RC0 | DIMM4, RC0 | DIMM6,
		RC0 | DIMM1, RC0 | DIMM3,
		RC0 | DIMM5, RC0 | DIMM7,
		// Node 1
		RC1 | DIMM0, RC1 | DIMM2,
		RC1 | DIMM4, RC1 | DIMM6,
		RC1 | DIMM1, RC1 | DIMM3,
		RC1 | DIMM5, RC1 | DIMM7,
	};

	struct sys_info *sysinfo = &sysinfo_car;
	int needs_reset = 0;
	unsigned bsp_apicid = 0;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		sio_setup();
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	w83627hf_set_clksel_48(DUMMY_DEV);
	winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);

	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);

	setup_mb_resource_map();

	printk(BIOS_DEBUG, "bsp_apicid=%02x\n", bsp_apicid);

	set_sysinfo_in_ram(0);	// in BSP so could hold all ap until sysinfo is in ram
#if CONFIG_DEBUG_SMBUS
	dump_smbus_registers();
#endif
	setup_coherent_ht_domain();	// routing table and start other core0

	wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
	// It is said that we should start core1 after all core0 launched
	/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
	 * So here need to make sure last core0 is started, esp for two way system,
	 * (there may be apic id conflicts in that case)
	 */
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* it will set up chains and store link pair for optimization later */
	ht_setup_chains_x(sysinfo);	// it will init sblnk and sbbusn, nodes, sbdn

#if CONFIG_SET_FIDVID
	{
		msr_t msr;
		msr = rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "begin msr fid, vid %08x%08x\n", msr.hi, msr.lo);
	}
	enable_fid_change();
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
	init_fidvid_bsp(bsp_apicid);
	// show final fid and vid
	{
		msr_t msr;
		msr = rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "end   msr fid, vid %08x%08x\n", msr.hi, msr.lo);
	}
#endif

	init_timer(); /* Need to use TMICT to synchronize FID/VID. */

	needs_reset |= optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	needs_reset |= mcp55_early_setup_x();

	// fidvid change will issue one LDTSTOP and the HT change will be effective too
	if (needs_reset) {
		printk(BIOS_INFO, "ht reset -\n");
		soft_reset();
	}

	allow_all_aps_stop(bsp_apicid);

	//It's the time to set ctrl in sysinfo now;
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	struct sys_info *sysinfo = &sysinfo_car;

	u32 bsp_apicid = 0, val, wants_reset;
	msr_t msr;

	timestamp_init(timestamp_get());
	timestamp_add_now(TS_START_ROMSTAGE);

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		set_bsp_node_CHtExtNodeCfgEn();
		enumerate_ht_chain();
		sio_setup();
	}

	post_code(0x30);

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	post_code(0x32);

	winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	console_init();

	if (CONFIG_MAX_PHYSICAL_CPUS != 2)
		printk(BIOS_WARNING, "CONFIG_MAX_PHYSICAL_CPUS is %d, but this is a dual socket board!\n", CONFIG_MAX_PHYSICAL_CPUS);

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	val = cpuid_eax(1);
	printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
	printk(BIOS_DEBUG, "bsp_apicid = %02x\n", bsp_apicid);
	printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);

	/* Setup sysinfo defaults */
	set_sysinfo_in_ram(0);

	update_microcode(val);

	post_code(0x33);

	cpuSetAMDMSR(0);
	post_code(0x34);

	amd_ht_init(sysinfo);
	post_code(0x35);

	/* Setup nodes PCI space and start core 0 AP init. */
	finalize_node_setup(sysinfo);

	/* Setup any mainboard PCI settings etc. */
	setup_mb_resource_map();
	post_code(0x36);

	/* wait for all the APs core0 started by finalize_node_setup. */
	/* FIXME: A bunch of cores are going to start output to serial at once.
	 * It would be nice to fix up prink spinlocks for ROM XIP mode.
	 * I think it could be done by putting the spinlock flag in the cache
	 * of the BSP located right after sysinfo.
	 */
	wait_all_core0_started();

	if (IS_ENABLED(CONFIG_SET_FIDVID)) {
		msr = rdmsr(0xc0010071);
		printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);

		post_code(0x39);

		if (!warm_reset_detect(0)) {			// BSP is node 0
			init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
		} else {
			init_fidvid_stage2(bsp_apicid, 0);	// BSP is node 0
		}

		post_code(0x3A);

		/* show final fid and vid */
		msr = rdmsr(0xc0010071);
		printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);
	}

	if (IS_ENABLED(CONFIG_LOGICAL_CPUS)) {
		/* Core0 on each node is configured. Now setup any additional cores. */
		printk(BIOS_DEBUG, "start_other_cores()\n");
		start_other_cores(bsp_apicid);
		post_code(0x37);
		wait_all_other_cores_started(bsp_apicid);
	}

	printk(BIOS_DEBUG, "set_ck804_base_unit_id()\n");
	ck804_control(ctrl_conf_fix_pci_numbering, ARRAY_SIZE(ctrl_conf_fix_pci_numbering), CK804_BOARD_BOOT_BASE_UNIT_UID);

	post_code(0x38);

//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr[] = {
		// first node
		DIMM0, DIMM2, 0, 0,
		DIMM1, DIMM3, 0, 0,
		// second node
		DIMM4, DIMM6, 0, 0,
		DIMM5, DIMM7, 0, 0,
	};

	struct sys_info *sysinfo = &sysinfo_car;
	int needs_reset;
	unsigned bsp_apicid = 0;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		bcm5785_enable_lpc();
		pc87417_enable_dev(RTC_DEV); /* Enable RTC */
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	pilot_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);

	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

//	setup_early_ipmi_serial();
	pilot_early_init(SERIAL_DEV); //config port is being taken from SERIAL_DEV
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
	printk(BIOS_DEBUG, "bsp_apicid=%02x\n", bsp_apicid);

#if CONFIG_MEM_TRAIN_SEQ == 1
	set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
	setup_coherent_ht_domain();

	wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
	// It is said that we should start core1 after all core0 launched
	/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
	 * So here need to make sure last core0 is started, esp for two way system,
	 * (there may be apic id conflicts in that case)
	*/
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* it will set up chains and store link pair for optimization later */
	ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
	bcm5785_early_setup();

#if CONFIG_SET_FIDVID
	{
		msr_t msr;
		msr=rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "begin msr fid, vid %08x %08x\n", msr.hi, msr.lo);
	}
	enable_fid_change();
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
	init_fidvid_bsp(bsp_apicid);
	// show final fid and vid
	{
		msr_t msr;
		msr=rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "end msr fid, vid %08x %08x\n", msr.hi, msr.lo);
	}
#endif

	needs_reset = optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);

	// fidvid change will issue one LDTSTOP and the HT change will be effective too
	if (needs_reset) {
		printk(BIOS_INFO, "ht reset -\n");
		soft_reset();
	}

	allow_all_aps_stop(bsp_apicid);

	//It's the time to set ctrl in sysinfo now;
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
	enable_smbus();

	//do we need apci timer, tsc...., only debug need it for better output
	/* all ap stopped? */
	// init_timer(); // Need to use TMICT to synconize FID/VID

	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);

	post_cache_as_ram();
}

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr[] = {
			// first node
                        DIMM0, DIMM2, 0, 0,
                        DIMM1, DIMM3, 0, 0,

			// second node
                        DIMM4, DIMM6, 0, 0,
                        DIMM5, DIMM7, 0, 0,
	};

	struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE
		+ CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
        int needs_reset;
        unsigned bsp_apicid = 0;

        if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

 	w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
        console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);

        setup_default_resource_map();

	print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");

#if CONFIG_MEM_TRAIN_SEQ == 1
        set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
	setup_coherent_ht_domain(); // routing table and start other core0

	wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS==1
        // It is said that we should start core1 after all core0 launched
	/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
	 * So here need to make sure last core0 is started, esp for two way system,
	 * (there may be apic id conflicts in that case)
	 */
        start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* it will set up chains and store link pair for optimization later */
        ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn

#if CONFIG_SET_FIDVID
        {
                msr_t msr;
	        msr=rdmsr(0xc0010042);
                print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
        }
	enable_fid_change();
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
        init_fidvid_bsp(bsp_apicid);
        // show final fid and vid
        {
                msr_t msr;
               	msr=rdmsr(0xc0010042);
               	print_debug("end   msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
        }
#endif

	needs_reset = optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);

        // fidvid change will issue one LDTSTOP and the HT change will be effective too
        if (needs_reset) {
                print_info("ht reset -\n");
                soft_reset_x(sysinfo->sbbusn, sysinfo->sbdn);
        }

	allow_all_aps_stop(bsp_apicid);

        //It's the time to set ctrl in sysinfo now;
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	enable_smbus();

#if 0
	dump_smbus_registers();
#endif

	memreset_setup();

	//do we need apci timer, tsc...., only debug need it for better output
        /* all ap stopped? */
        init_timer(); // Need to use TMICT to synconize FID/VID
	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);

#if 0
        dump_pci_devices();
#endif

        post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	struct sys_info *sysinfo = &sysinfo_car;
	u32 bsp_apicid = 0, val;
	msr_t msr;

	timestamp_init(timestamp_get());
	timestamp_add_now(TS_START_ROMSTAGE);

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		/* mov bsp to bus 0xff when > 8 nodes */
		set_bsp_node_CHtExtNodeCfgEn();
		enumerate_ht_chain();
		bcm5785_enable_lpc();
		pc87417_enable_dev(RTC_DEV); /* Enable RTC */
	}

	post_code(0x30);

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	pilot_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);

	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	pilot_early_init(SERIAL_DEV); //config port is being taken from SERIAL_DEV

	val = cpuid_eax(1);
	printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
	printk(BIOS_DEBUG, "bsp_apicid = %02x\n", bsp_apicid);
	printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);

	/* Setup sysinfo defaults */
	set_sysinfo_in_ram(0);

	update_microcode(val);

	post_code(0x33);

	cpuSetAMDMSR(0);
	post_code(0x34);

	amd_ht_init(sysinfo);
	post_code(0x35);

	/* Setup nodes PCI space and start core 0 AP init. */
	finalize_node_setup(sysinfo);

	post_code(0x36);

	/* wait for all the APs core0 started by finalize_node_setup. */
	/* FIXME: A bunch of cores are going to start output to serial at once.
	 * It would be nice to fixup prink spinlocks for ROM XIP mode.
	 * I think it could be done by putting the spinlock flag in the cache
	 * of the BSP located right after sysinfo.
	 */

	wait_all_core0_started();

#if CONFIG_LOGICAL_CPUS
	/* Core0 on each node is configured. Now setup any additional cores. */
	printk(BIOS_DEBUG, "start_other_cores()\n");
	start_other_cores(bsp_apicid);
	post_code(0x37);
	wait_all_other_cores_started(bsp_apicid);
#endif

#if CONFIG_SET_FIDVID
	msr = rdmsr(0xc0010071);
	printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);

	/* FIXME: The sb fid change may survive the warm reset and only
	 * need to be done once.*/

	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);

	post_code(0x39);

	if (!warm_reset_detect(0)) {                    // BSP is node 0
		init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
	} else {
		init_fidvid_stage2(bsp_apicid, 0);      // BSP is node 0
	}

	post_code(0x3A);

	/* show final fid and vid */
	msr = rdmsr(0xc0010071);
	printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);
#endif

	init_timer();

//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const u16 spd_addr[] = {
		DIMM0, DIMM2, 0, 0,	/* Channel A (DIMM_A1, DIMM_A2) */
		DIMM1, DIMM3, 0, 0,	/* Channel B (DIMM_B1, DIMM_B2) */
	};

	struct sys_info *sysinfo = &sysinfo_car;
	int needs_reset = 0;
	unsigned bsp_apicid = 0;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Allow the HT devices to be found. */
		enumerate_ht_chain();
		sio_setup();
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_24);
	ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);

	setup_mb_resource_map();
	report_bist_failure(bist);
	console_init();

	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo, sysinfo + 1);
	printk(BIOS_DEBUG, "bsp_apicid=0x%02x\n", bsp_apicid);

	/* In BSP so could hold all AP until sysinfo is in RAM. */
	set_sysinfo_in_ram(0);

	setup_coherent_ht_domain(); /* Routing table and start other core0. */
	wait_all_core0_started();

#if CONFIG_LOGICAL_CPUS
	/*
	 * It is said that we should start core1 after all core0 launched
	 * becase optimize_link_coherent_ht is moved out from
	 * setup_coherent_ht_domain, so here need to make sure last core0 is
	 * started, esp for two way system (there may be APIC ID conflicts in
	 * that case).
	 */
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* Set up chains and store link pair for optimization later. */
	ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */

	/* TODO: FIDVID */

	init_timer(); /* Need to use TMICT to synchronize FID/VID. */

	needs_reset |= optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	needs_reset |= mcp55_early_setup_x();

	/*
	 * FIDVID change will issue one LDTSTOP and the HT change will be
	 * effective too.
	 */
	if (needs_reset) {
		printk(BIOS_INFO, "ht reset -\n");
		soft_reset();
	}
	allow_all_aps_stop(bsp_apicid);

	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	enable_smbus();

	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);

	/* BSP switch stack to RAM and copy sysinfo RAM now. */
	post_cache_as_ram();
}