C++ enumerate_ht_chain函数代码示例

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const u16 spd_addr[] = { DIMM0, 0, 0, 0, DIMM1, 0, 0, 0, };
	int needs_reset = 0;
	u32 bsp_apicid = 0;
	msr_t msr;
	struct cpuid_result cpuid1;
	struct sys_info *sysinfo = &sysinfo_car;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		/* sb600_lpc_port80(); */
		sb600_pci_port80();
	}

	technexion_post_code_init();
	technexion_post_code(LED_MESSAGE_START);

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	enable_rs690_dev8();
	sb600_lpc_init();

	ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	ite_kill_watchdog(GPIO_DEV);

	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);
	printk(BIOS_DEBUG, "bsp_apicid=0x%x\n", bsp_apicid);

	setup_tim5690_resource_map();

	setup_coherent_ht_domain();

#if CONFIG_LOGICAL_CPUS
	/* It is said that we should start core1 after all core0 launched */
	wait_all_core0_started();
	start_other_cores();
#endif
	wait_all_aps_started(bsp_apicid);

	ht_setup_chains_x(sysinfo);

	/* run _early_setup before soft-reset. */
	rs690_early_setup();
	sb600_early_setup();

	/* Check to see if processor is capable of changing FIDVID  */
	/* otherwise it will throw a GP# when reading FIDVID_STATUS */
	cpuid1 = cpuid(0x80000007);
	if ((cpuid1.edx & 0x6) == 0x6) {
		/* Read FIDVID_STATUS */
		msr=rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "begin msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);

		enable_fid_change();
		enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
		init_fidvid_bsp(bsp_apicid);

		/* show final fid and vid */
		msr=rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "end msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
	} else {
		printk(BIOS_DEBUG, "Changing FIDVID not supported\n");
	}

	needs_reset = optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	rs690_htinit();
	printk(BIOS_DEBUG, "needs_reset=0x%x\n", needs_reset);

	if (needs_reset) {
		printk(BIOS_INFO, "ht reset -\n");
		soft_reset();
	}

	speaker_init(255);
	speaker_on_nodelay();

	allow_all_aps_stop(bsp_apicid);

	/* It's the time to set ctrl now; */
	printk(BIOS_DEBUG, "sysinfo->nodes: %2x  sysinfo->ctrl: %p  spd_addr: %p\n",
		     sysinfo->nodes, sysinfo->ctrl, spd_addr);

	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	technexion_post_code(LED_MESSAGE_RAM);

	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);

	speaker_off_nodelay();

	rs690_before_pci_init();
	sb600_before_pci_init();
//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr [] = {
		// Node 0
		DIMM0, DIMM2, 0, 0,
		DIMM1, DIMM3, 0, 0,
		// Node 1
		DIMM4, DIMM6, 0, 0,
		DIMM5, DIMM7, 0, 0,
	};

	struct sys_info *sysinfo = &sysinfo_car;
	int needs_reset = 0;
	unsigned bsp_apicid = 0;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		sio_setup();
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	setup_mb_resource_map();

	dme1737_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);

	printk(BIOS_DEBUG, "bsp_apicid=%02x\n", bsp_apicid);

	set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
	setup_coherent_ht_domain(); // routing table and start other core0

	wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
	// It is said that we should start core1 after all core0 launched
	/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
	 * So here need to make sure last core0 is started, esp for two way system,
	 * (there may be apic id conflicts in that case)
	 */
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* it will set up chains and store link pair for optimization later */
	ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn

#if CONFIG_SET_FIDVID
	{
		msr_t msr;
		msr=rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "begin msr fid, vid %08x%08x\n", msr.hi, msr.lo);
	}
	enable_fid_change();
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
	init_fidvid_bsp(bsp_apicid);
	// show final fid and vid
	{
		msr_t msr;
		msr=rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "end   msr fid, vid %08x%08x\n", msr.hi, msr.lo);
	}
#endif

	init_timer(); /* Need to use TMICT to synchronize FID/VID. */

	needs_reset |= optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	needs_reset |= mcp55_early_setup_x();

	/* mask NMI from constantly-asserted-on-this-board SERR# */
	outb((inb(NMI_SC) & 0x0f) | PCI_SERR_EN, NMI_SC);

	// fidvid change will issue one LDTSTOP and the HT change will be effective too
	if (needs_reset) {
		printk(BIOS_INFO, "ht reset -\n");
		soft_reset();
	}
	allow_all_aps_stop(bsp_apicid);

	//It's the time to set ctrl in sysinfo now;
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	enable_smbus();

	/* all ap stopped? */

	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);

	post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
}

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
       static const uint16_t spd_addr[] = {
                      //first node
                       RC0|DIMM0, RC0|DIMM2, RC0|DIMM4, RC0|DIMM6,
                       RC0|DIMM1, RC0|DIMM3, RC0|DIMM5, RC0|DIMM7,
                       //second node
                       RC1|DIMM0, RC1|DIMM2, RC1|DIMM4, RC1|DIMM6,
                       RC1|DIMM1, RC1|DIMM3, RC1|DIMM5, RC1|DIMM7,
       };

	struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE +
		CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);

        int needs_reset;
        unsigned bsp_apicid = 0;

        if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		bcm5785_enable_lpc();
		//enable RTC
		pc87417_enable_dev(RTC_DEV);
        }

        if (bist == 0)
               bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

        pc87417_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
        console_init();

//     dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);

       /* Halt if there was a built in self test failure */
       report_bist_failure(bist);

       printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);

       setup_ms9185_resource_map();
#if 0
       dump_pci_device(PCI_DEV(0, 0x18, 0));
       dump_pci_device(PCI_DEV(0, 0x19, 0));
#endif

       print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");

       setup_coherent_ht_domain();

       wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS==1
        // It is said that we should start core1 after all core0 launched
       /* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
        * So here need to make sure last core0 is started, esp for two way system,
        * (there may be apic id conflicts in that case)
        */
        start_other_cores();
//bx_a010-     wait_all_other_cores_started(bsp_apicid);
#endif

       /* it will set up chains and store link pair for optimization later */
       ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn

       bcm5785_early_setup();

#if 0
       //it your CPU min fid is 1G, you can change HT to 1G and FID to max one time.
        needs_reset = optimize_link_coherent_ht();
        needs_reset |= optimize_link_incoherent_ht(sysinfo);
#endif

#if CONFIG_SET_FIDVID
        {
                msr_t msr;
                msr=rdmsr(0xc0010042);
                print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
        }
        enable_fid_change();
        enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
        init_fidvid_bsp(bsp_apicid);
        // show final fid and vid
        {
                msr_t msr;
                msr=rdmsr(0xc0010042);
                print_debug("end   msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
        }
#endif

#if 1
       needs_reset = optimize_link_coherent_ht();
       needs_reset |= optimize_link_incoherent_ht(sysinfo);

        // fidvid change will issue one LDTSTOP and the HT change will be effective too
        if (needs_reset) {
                print_info("ht reset -\n");
                soft_reset();
        }
#endif
       allow_all_aps_stop(bsp_apicid);

//.........这里部分代码省略.........

static void bootblock_northbridge_init(void) {
	enumerate_ht_chain();
}

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr[] = {
		// Node 0
		DIMM0, DIMM2, 0, 0,
		0, 0, 0, 0,
		// Node 1
		DIMM1, DIMM3, 0, 0,
		0, 0, 0, 0,
	};
	unsigned bsp_apicid = 0;
	int needs_reset = 0;
	struct sys_info *sysinfo = &sysinfo_car;

	sio_init();
	w83627ehg_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	console_init();
	enable_rom_decode();

	print_info("now booting... fallback\n");

	/* Is this a CPU only reset? Or is this a secondary CPU? */
	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0. */
		/* Allow the HT devices to be found. */
		enumerate_ht_chain();
	}

	// FIXME why is this executed again? --->
	sio_init();
	w83627ehg_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	console_init();
	enable_rom_decode();
	// <--- FIXME why is this executed again?

	print_info("now booting... real_main\n");

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	/* Halt if there was a built in self test failure. */
	report_bist_failure(bist);

	setup_default_resource_map();
	setup_coherent_ht_domain();
	wait_all_core0_started();

	print_info("now booting... Core0 started\n");

#if CONFIG_LOGICAL_CPUS
	/* It is said that we should start core1 after all core0 launched. */
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif
	init_timer();
	ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */

	needs_reset = optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	needs_reset |= k8t890_early_setup_ht();

	if (needs_reset) {
		print_debug("ht reset -\n");
		soft_reset();
	}

	/* the HT settings needs to be OK, because link freq chnage may cause HT disconnect */
	enable_fid_change();
	init_fidvid_bsp(bsp_apicid);

	/* Stop the APs so we can start them later in init. */
	allow_all_aps_stop(bsp_apicid);

	/* It's the time to set ctrl now. */
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	enable_smbus();
	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
	post_cache_as_ram();
}

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const u16 spd_addr[] = { DIMM0, 0, 0, 0, DIMM1, 0, 0, 0, };
	int needs_reset = 0;
	u32 bsp_apicid = 0;
	msr_t msr;
	struct cpuid_result cpuid1;
	struct sys_info *sysinfo = &sysinfo_car;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		sb600_lpc_port80();
		/* sb600_pci_port80(); */
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	enable_rs690_dev8();
	sb600_lpc_init();

	/* Pistachio used a FPGA to enable serial debug instead of a SIO
	 * and it doesn't require any special setup. */

	console_init();

	post_code(0x03);

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);
	printk(BIOS_DEBUG, "bsp_apicid=0x%x\n", bsp_apicid);

	setup_pistachio_resource_map();

	setup_coherent_ht_domain();

#if CONFIG_LOGICAL_CPUS
	/* It is said that we should start core1 after all core0 launched */
	wait_all_core0_started();
	start_other_cores();
#endif
	wait_all_aps_started(bsp_apicid);

	/* it will set up chains and store link pair for optimization later,
	 * it will init sblnk and sbbusn, nodes, sbdn */
	ht_setup_chains_x(sysinfo);

	/* run _early_setup before soft-reset. */
	rs690_early_setup();
	sb600_early_setup();

	post_code(0x04);

	/* Check to see if processor is capable of changing FIDVID  */
	/* otherwise it will throw a GP# when reading FIDVID_STATUS */
	cpuid1 = cpuid(0x80000007);
	if ((cpuid1.edx & 0x6) == 0x6) {
		/* Read FIDVID_STATUS */
		msr=rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "begin msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);

		enable_fid_change();
		enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
		init_fidvid_bsp(bsp_apicid);

		/* show final fid and vid */
		msr=rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "end msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
	} else {
		printk(BIOS_DEBUG, "Changing FIDVID not supported\n");
	}

	post_code(0x05);

	needs_reset = optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	rs690_htinit();
	printk(BIOS_DEBUG, "needs_reset=0x%x\n", needs_reset);

	post_code(0x06);

	if (needs_reset) {
		print_info("ht reset -\n");
		soft_reset();
	}

	allow_all_aps_stop(bsp_apicid);

	/* It's the time to set ctrl now; */
	printk(BIOS_DEBUG, "sysinfo->nodes: %2x  sysinfo->ctrl: %p  spd_addr: %p\n",
		     sysinfo->nodes, sysinfo->ctrl, spd_addr);
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	post_code(0x07);

	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);

	post_code(0x08);
//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const u16 spd_addr[] = { DIMM0, 0, 0, 0, DIMM1, 0, 0, 0, };
	int needs_reset = 0;
	u32 bsp_apicid = 0;
	msr_t msr;
	struct cpuid_result cpuid1;
	struct sys_info *sysinfo = &sysinfo_car;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();

		/* sb600_lpc_port80(); */
		sb600_pci_port80();
	}

	if (bist == 0) {
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
	}

	enable_rs690_dev8(); // enable CFG access to Dev8, which is the SB P2P Bridge
	sb600_lpc_init();
#if defined(DUMP_CMOS_RAM) && (DUMP_CMOS_RAM == 0)
	check_cmos();  // rebooting in case of corrupted cmos !!!!!
#endif
	/* it8712f_enable_serial does not use its 1st parameter. */
	it8712f_enable_serial(0, CONFIG_TTYS0_BASE);
	it8712f_kill_watchdog();

	console_init();
#if defined(DUMP_CMOS_RAM) && (DUMP_CMOS_RAM == 1)
	check_cmos();  // rebooting in case of corrupted cmos !!!!!
#endif
	post_code(0x03);

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);
	__DEBUG__("bsp_apicid=0x%x\n", bsp_apicid);

	setup_sitemp_resource_map();

	setup_coherent_ht_domain();

#if CONFIG_LOGICAL_CPUS
	/* It is said that we should start core1 after all core0 launched */
	wait_all_core0_started();
	start_other_cores();
#endif
	wait_all_aps_started(bsp_apicid);

	ht_setup_chains_x(sysinfo);

	/* run _early_setup before soft-reset. */
	rs690_early_setup();
	sb600_early_setup();

	post_code(0x04);

	/* Check to see if processor is capable of changing FIDVID  */
	/* otherwise it will throw a GP# when reading FIDVID_STATUS */
	cpuid1 = cpuid(0x80000007);
	if( (cpuid1.edx & 0x6) == 0x6 ) {

		/* Read FIDVID_STATUS */
		msr=rdmsr(0xc0010042);
		__DEBUG__("begin msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);

		enable_fid_change();
		enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
		init_fidvid_bsp(bsp_apicid);

		/* show final fid and vid */
		msr=rdmsr(0xc0010042);
		__DEBUG__("end msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);

	} else {
		__DEBUG__("Changing FIDVID not supported\n");
	}

	post_code(0x05);

	needs_reset = optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	rs690_htinit();
	__DEBUG__("needs_reset=0x%x\n", needs_reset);

	post_code(0x06);

	if (needs_reset) {
		__INFO__("ht reset -\n");
		soft_reset();
	}

	allow_all_aps_stop(bsp_apicid);

	/* It's the time to set ctrl now; */
	__DEBUG__("sysinfo->nodes: %2x  sysinfo->ctrl: %p  spd_addr: %p\n",
		     sysinfo->nodes, sysinfo->ctrl, spd_addr);
//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr [] = {
			// Node 0
			(0xa<<3)|0, (0xa<<3)|2, 0, 0,
			(0xa<<3)|1, (0xa<<3)|3, 0, 0,
			// Node 1
			(0xa<<3)|4, (0xa<<3)|6, 0, 0,
			(0xa<<3)|5, (0xa<<3)|7, 0, 0,
	};

	struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE
		+ CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);

	int needs_reset = 0;
	unsigned bsp_apicid = 0;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */

		enumerate_ht_chain();

		sio_setup();

		/* Setup the mcp55 */
		mcp55_enable_rom();
	}

	if (bist == 0) {
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
	}

	w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);

	setup_mb_resource_map();

	uart_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

#if CONFIG_USBDEBUG
	mcp55_enable_usbdebug(CONFIG_USBDEBUG_DEFAULT_PORT);
	early_usbdebug_init();
#endif
	console_init();
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);

	print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");

#if CONFIG_MEM_TRAIN_SEQ == 1
	set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
	setup_coherent_ht_domain(); // routing table and start other core0

	wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS==1
	// It is said that we should start core1 after all core0 launched
	/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
	 * So here need to make sure last core0 is started, esp for two way system,
	 * (there may be apic id conflicts in that case)
	 */
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* it will set up chains and store link pair for optimization later */
	ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn

#if SET_FIDVID == 1

	{
		msr_t msr;
		msr=rdmsr(0xc0010042);
		print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");

	}

	enable_fid_change();

	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);

	init_fidvid_bsp(bsp_apicid);

	// show final fid and vid
	{
		msr_t msr;
		msr=rdmsr(0xc0010042);
		print_debug("end   msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");

	}
#endif

	init_timer(); // Need to use TMICT to synconize FID/VID

	needs_reset |= optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	needs_reset |= mcp55_early_setup_x();

//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr [] = {
		DIMM0, 0, 0, 0,
		DIMM1, 0, 0, 0,
	};

	int needs_reset;
	unsigned bsp_apicid = 0, nodes;
	struct mem_controller ctrl[8];

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		sio_setup();
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx);

//	post_code(0x32);

	winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

#if 0
	dump_pci_device(PCI_DEV(0, 0x18, 0));
#endif

	needs_reset = setup_coherent_ht_domain();

	wait_all_core0_started();
	// It is said that we should start core1 after all core0 launched
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);

#if CONFIG_SET_FIDVID
	/* Check to see if processor is capable of changing FIDVID  */
	/* otherwise it will throw a GP# when reading FIDVID_STATUS */
	if ((cpuid_edx(0x80000007) & 0x6) == 0x6) {
		msr_t msr;
		/* Read FIDVID_STATUS */
		msr = rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "begin msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);

		enable_fid_change();
		init_fidvid_bsp(bsp_apicid);

		msr = rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "end msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
	}
#endif

	needs_reset |= ht_setup_chains_x();
	needs_reset |= ck804_early_setup_x();
	if (needs_reset) {
		printk(BIOS_INFO, "ht reset -\n");
		soft_reset();
	}

	allow_all_aps_stop(bsp_apicid);

	nodes = get_nodes();
	//It's the time to set ctrl now;
	fill_mem_ctrl(nodes, ctrl, spd_addr);

	enable_smbus();
#if 0
	dump_spd_registers(&cpu[0]);
	dump_smbus_registers();
#endif

	memreset_setup();
	sdram_initialize(nodes, ctrl);

#if 0
	print_pci_devices();
	dump_pci_devices();
#endif

	post_cache_as_ram();
}

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr[] = {
		// Node 0
		RC0|DIMM0, RC0|DIMM2, RC0|DIMM4, RC0|DIMM6,
		RC0|DIMM1, RC0|DIMM3, RC0|DIMM5, RC0|DIMM7,
		// node 1
		RC1|DIMM0, RC1|DIMM2, RC1|DIMM4, RC1|DIMM6,
		RC1|DIMM1, RC1|DIMM3, RC1|DIMM5, RC1|DIMM7,
	};

	unsigned bsp_apicid = 0;
	int needs_reset;
	struct sys_info *sysinfo = &sysinfo_car;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		sio_setup();
	}

	if (bist == 0) {
		//init_cpus(cpu_init_detectedx);
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
	}

	winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	setup_ms9282_resource_map();

	setup_coherent_ht_domain();

	wait_all_core0_started();

#if CONFIG_LOGICAL_CPUS
	// It is said that we should start core1 after all core0 launched
	start_other_cores();
	//wait_all_other_cores_started(bsp_apicid);
#endif
	ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn

	init_timer(); /* Need to use TMICT to synchronize FID/VID. */

	needs_reset = optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	needs_reset |= mcp55_early_setup_x();
	if (needs_reset) {
		printk(BIOS_INFO, "ht reset -\n");
		soft_reset();
	}

	//It's the time to set ctrl now;
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	enable_smbus();

	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);

	post_cache_as_ram();
}

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const u16 spd_addr[] = {
		DIMM0, DIMM1, 0, 0,
		0, 0, 0, 0,
		0, 0, 0, 0,
		0, 0, 0, 0,
	};

	int needs_reset;
	unsigned bsp_apicid = 0, nodes;
	struct mem_controller ctrl[8];

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		sio_setup();
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx);

	winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	needs_reset = setup_coherent_ht_domain();

	wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
	// It is said that we should start core1 after all core0 launched
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	needs_reset |= ht_setup_chains_x();
	needs_reset |= ck804_early_setup_x();
	if (needs_reset) {
		print_info("ht reset -\n");
		soft_reset();
	}

	allow_all_aps_stop(bsp_apicid);

	nodes = get_nodes();
	//It's the time to set ctrl now;
	fill_mem_ctrl(nodes, ctrl, spd_addr);

	enable_smbus();

	ms7135_set_nf4_voltage();
	ms7135_set_ram_voltage();

#if CONFIG_DEBUG_SMBUS
	dump_spd_registers(&ctrl[0]);
	dump_smbus_registers();
#endif

	sdram_initialize(nodes, ctrl);

	post_cache_as_ram();
}

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	struct sys_info *sysinfo = &sysinfo_car;
	u32 bsp_apicid = 0, val;
	msr_t msr;

	timestamp_init(timestamp_get());
	timestamp_add_now(TS_START_ROMSTAGE);

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		/* mov bsp to bus 0xff when > 8 nodes */
		set_bsp_node_CHtExtNodeCfgEn();
		enumerate_ht_chain();
		bcm5785_enable_lpc();
		pc87417_enable_dev(RTC_DEV); /* Enable RTC */
	}

	post_code(0x30);

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	pilot_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);

	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	pilot_early_init(SERIAL_DEV); //config port is being taken from SERIAL_DEV

	val = cpuid_eax(1);
	printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
	printk(BIOS_DEBUG, "bsp_apicid = %02x\n", bsp_apicid);
	printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);

	/* Setup sysinfo defaults */
	set_sysinfo_in_ram(0);

	update_microcode(val);

	post_code(0x33);

	cpuSetAMDMSR(0);
	post_code(0x34);

	amd_ht_init(sysinfo);
	post_code(0x35);

	/* Setup nodes PCI space and start core 0 AP init. */
	finalize_node_setup(sysinfo);

	post_code(0x36);

	/* wait for all the APs core0 started by finalize_node_setup. */
	/* FIXME: A bunch of cores are going to start output to serial at once.
	 * It would be nice to fixup prink spinlocks for ROM XIP mode.
	 * I think it could be done by putting the spinlock flag in the cache
	 * of the BSP located right after sysinfo.
	 */

	wait_all_core0_started();

#if CONFIG_LOGICAL_CPUS
	/* Core0 on each node is configured. Now setup any additional cores. */
	printk(BIOS_DEBUG, "start_other_cores()\n");
	start_other_cores(bsp_apicid);
	post_code(0x37);
	wait_all_other_cores_started(bsp_apicid);
#endif

#if CONFIG_SET_FIDVID
	msr = rdmsr(0xc0010071);
	printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);

	/* FIXME: The sb fid change may survive the warm reset and only
	 * need to be done once.*/

	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);

	post_code(0x39);

	if (!warm_reset_detect(0)) {                    // BSP is node 0
		init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
	} else {
		init_fidvid_stage2(bsp_apicid, 0);      // BSP is node 0
	}

	post_code(0x3A);

	/* show final fid and vid */
	msr = rdmsr(0xc0010071);
	printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);
#endif

	init_timer();

//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr[] = {
		// Node 0
		DIMM0, DIMM2, 0, 0,
		DIMM1, DIMM3, 0, 0,
		// Node 1
		DIMM4, DIMM6, 0, 0,
		DIMM5, DIMM7, 0, 0,
	};

	struct sys_info *sysinfo = &sysinfo_car;
	int needs_reset = 0;
	unsigned bsp_apicid = 0;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0. */
		/* Allow the HT devices to be found. */
		enumerate_ht_chain();
		sio_setup();
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	/* FIXME: This should be part of the Super I/O code/config. */
	pnp_enter_ext_func_mode(SERIAL_DEV);
	/* Switch CLKSEL to 24MHz (default is 48MHz). Needed for serial! */
	pnp_write_config(SERIAL_DEV, 0x24, 0);
	w83627ehg_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
	pnp_exit_ext_func_mode(SERIAL_DEV);

	setup_mb_resource_map();
	console_init();
	report_bist_failure(bist); /* Halt upon BIST failure. */

	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
	print_debug("bsp_apicid=");
	print_debug_hex8(bsp_apicid);
	print_debug("\n");

#if CONFIG_MEM_TRAIN_SEQ == 1
	/* In BSP so could hold all AP until sysinfo is in RAM. */
	set_sysinfo_in_ram(0);
#endif

	setup_coherent_ht_domain(); /* Routing table and start other core0. */
	wait_all_core0_started();

#if CONFIG_LOGICAL_CPUS
	/* It is said that we should start core1 after all core0 launched
	 * becase optimize_link_coherent_ht is moved out from
	 * setup_coherent_ht_domain, so here need to make sure last core0 is
	 * started, esp for two way system (there may be APIC ID conflicts in
	 * that case).
	 */
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* Set up chains and store link pair for optimization later. */
	ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */

#if CONFIG_SET_FIDVID
	{
		msr_t msr = rdmsr(0xc0010042);
		print_debug("begin msr fid, vid ");
		print_debug_hex32(msr.hi);
		print_debug_hex32(msr.lo);
		print_debug("\n");
	}
	enable_fid_change();
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
	init_fidvid_bsp(bsp_apicid);
	{
		msr_t msr = rdmsr(0xc0010042);
		print_debug("end   msr fid, vid ");
		print_debug_hex32(msr.hi);
		print_debug_hex32(msr.lo);
		print_debug("\n");
	}
#endif

	init_timer(); /* Need to use TMICT to synconize FID/VID. */

	needs_reset |= optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);
	needs_reset |= mcp55_early_setup_x();

	/* fidvid change will issue one LDTSTOP and the HT change will be effective too. */
	if (needs_reset) {
		print_info("ht reset -\n");
		soft_reset();
	}
	allow_all_aps_stop(bsp_apicid);

	/* It's the time to set ctrl in sysinfo now. */
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	enable_smbus();
//.........这里部分代码省略.........

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const uint16_t spd_addr[] = {
		// first node
		DIMM0, DIMM2, 0, 0,
		DIMM1, DIMM3, 0, 0,
		// second node
		DIMM4, DIMM6, 0, 0,
		DIMM5, DIMM7, 0, 0,
	};

	struct sys_info *sysinfo = &sysinfo_car;
	int needs_reset;
	unsigned bsp_apicid = 0;

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		bcm5785_enable_lpc();
		pc87417_enable_dev(RTC_DEV); /* Enable RTC */
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);

	pilot_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);

	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

//	setup_early_ipmi_serial();
	pilot_early_init(SERIAL_DEV); //config port is being taken from SERIAL_DEV
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
	printk(BIOS_DEBUG, "bsp_apicid=%02x\n", bsp_apicid);

#if CONFIG_MEM_TRAIN_SEQ == 1
	set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
	setup_coherent_ht_domain();

	wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
	// It is said that we should start core1 after all core0 launched
	/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
	 * So here need to make sure last core0 is started, esp for two way system,
	 * (there may be apic id conflicts in that case)
	*/
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);
#endif

	/* it will set up chains and store link pair for optimization later */
	ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
	bcm5785_early_setup();

#if CONFIG_SET_FIDVID
	{
		msr_t msr;
		msr=rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "begin msr fid, vid %08x %08x\n", msr.hi, msr.lo);
	}
	enable_fid_change();
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
	init_fidvid_bsp(bsp_apicid);
	// show final fid and vid
	{
		msr_t msr;
		msr=rdmsr(0xc0010042);
		printk(BIOS_DEBUG, "end msr fid, vid %08x %08x\n", msr.hi, msr.lo);
	}
#endif

	needs_reset = optimize_link_coherent_ht();
	needs_reset |= optimize_link_incoherent_ht(sysinfo);

	// fidvid change will issue one LDTSTOP and the HT change will be effective too
	if (needs_reset) {
		printk(BIOS_INFO, "ht reset -\n");
		soft_reset();
	}

	allow_all_aps_stop(bsp_apicid);

	//It's the time to set ctrl in sysinfo now;
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
	enable_smbus();

	//do we need apci timer, tsc...., only debug need it for better output
	/* all ap stopped? */
	// init_timer(); // Need to use TMICT to synconize FID/VID

	sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);

	post_cache_as_ram();
}

void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	static const u16 spd_addr [] = {
		DIMM0, DIMM2, 0, 0,
		DIMM1, DIMM3, 0, 0,
		DIMM4, DIMM6, 0, 0,
		DIMM5, DIMM7, 0, 0,
	};

	int needs_reset;
	unsigned bsp_apicid = 0, nodes;
	struct mem_controller ctrl[8];

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		enumerate_ht_chain();
		sio_setup();
	}

	if (bist == 0)
		bsp_apicid = init_cpus(cpu_init_detectedx);

	lpc47b397_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
	console_init();

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	sio_gpio_setup();

	setup_mb_resource_map();

	needs_reset = setup_coherent_ht_domain();

	wait_all_core0_started();

	// It is said that we should start core1 after all core0 launched
	start_other_cores();
	wait_all_other_cores_started(bsp_apicid);

	needs_reset |= ht_setup_chains_x();
	needs_reset |= ck804_early_setup_x();
	if (needs_reset) {
		printk(BIOS_INFO, "ht reset -\n");
		soft_reset();
	}

	allow_all_aps_stop(bsp_apicid);

	nodes = get_nodes();
	//It's the time to set ctrl now;
	fill_mem_ctrl(nodes, ctrl, spd_addr);

	enable_smbus();

	memreset_setup();
	sdram_initialize(nodes, ctrl);

	post_cache_as_ram();
}