当前位置: 首页>>代码示例>>C++>>正文

C++ devfs_add_partition函数代码示例

本文整理汇总了C++中devfs_add_partition函数的典型用法代码示例。如果您正苦于以下问题：C++ devfs_add_partition函数的具体用法？C++ devfs_add_partition怎么用？C++ devfs_add_partition使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。


在下文中一共展示了devfs_add_partition函数的15个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于系统推荐出更棒的C++代码示例。

示例1: nhk8815_devices_init

static int nhk8815_devices_init(void)
{
	writel(0xC37800F0, NOMADIK_GPIO1_BASE + 0x20);
	writel(0x00000000, NOMADIK_GPIO1_BASE + 0x24);
	writel(0x00000000, NOMADIK_GPIO1_BASE + 0x28);
	writel(readl(NOMADIK_SRC_BASE) | 0x8000, NOMADIK_SRC_BASE);

	/* Set up SMCS1 for Ethernet: sram-like, enabled, timing values */
	writel(0x0000305b, FSMC_BCR(1));
	writel(0x00033f33, FSMC_BTR(1));

	add_generic_device("smc91c111", DEVICE_ID_DYNAMIC, NULL, 0x34000300, 16,
			   IORESOURCE_MEM, NULL);

	platform_device_register(&nhk8815_nand_device);

	armlinux_set_architecture(MACH_TYPE_NOMADIK);
	armlinux_set_bootparams((void *)(0x00000100));

	devfs_add_partition("nand0", 0x0000000, 0x040000, DEVFS_PARTITION_FIXED, "xloader_raw");
	devfs_add_partition("nand0", 0x0040000, 0x080000, DEVFS_PARTITION_FIXED, "meminit_raw");
	devfs_add_partition("nand0", 0x0080000, 0x200000, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", 0x7FE0000, 0x020000, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	return 0;
}
开发者ID:Jokymon，项目名称:barebox，代码行数:28，代码来源:setup.c

示例2: eukrea_cpuimx25_devices_init

static int eukrea_cpuimx25_devices_init(void)
{
	eukrea_cpuimx25_mmu_init();

	mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx25_pads,
		ARRAY_SIZE(eukrea_cpuimx25_pads));
	register_device(&fec_dev);

	nand_info.width = 1;
	register_device(&nand_dev);

	devfs_add_partition("nand0", 0x00000, 0x40000,
		PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");

	devfs_add_partition("nand0", 0x40000, 0x20000,
		PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	register_device(&sdram0_dev);

	/* enable LCD */
	gpio_direction_output(26, 1);
	gpio_set_value(26, 1);

	register_device(&imxfb_dev);

	armlinux_add_dram(&sdram0_dev);
	armlinux_set_bootparams((void *)0x80000100);
	armlinux_set_architecture(MACH_TYPE_EUKREA_CPUIMX25);

	return 0;
}
开发者ID:ray650128，项目名称:barebox-sh4-nextvod，代码行数:33，代码来源:eukrea_cpuimx25.c

示例3: at91rm9200ek_devices_init

static int at91rm9200ek_devices_init(void)
{
	/*
	 * Correct IRDA resistor problem
	 * Set PA23_TXD in Output
	 */
	at91_set_gpio_output(AT91_PIN_PA23, 1);

	at91_add_device_eth(0, &ether_pdata);

	add_cfi_flash_device(0, AT91_CHIPSELECT_0, SZ_8M, 0);
	/* USB Host */
	at91_add_device_usbh_ohci(&ek_usbh_data);
	ek_device_add_leds();
	ek_add_device_udc();
	ek_add_device_spi();

#if defined(CONFIG_DRIVER_CFI) || defined(CONFIG_DRIVER_CFI_OLD)
	devfs_add_partition("nor0", 0x00000, 0x40000, DEVFS_PARTITION_FIXED, "self");
	devfs_add_partition("nor0", 0x40000, 0x20000, DEVFS_PARTITION_FIXED, "env0");
#endif

	armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
	armlinux_set_architecture(MACH_TYPE_AT91RM9200EK);

	return 0;
}
开发者ID:dgarnier，项目名称:barebox，代码行数:27，代码来源:init.c

示例4: tx25_devices_init

static int tx25_devices_init(void)
{
	gpio_fec_active();

	imx25_iim_register_fec_ethaddr();
	imx25_add_fec(&fec_info);

	if (readl(MX25_CCM_BASE_ADDR + MX25_CCM_RCSR) & (1 << 14))
		nand_info.width = 2;

	imx25_add_nand(&nand_info);

	devfs_add_partition("nand0", 0x00000, SZ_512K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");

	devfs_add_partition("nand0", SZ_512K, SZ_512K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	add_mem_device("sram0", 0x78000000, 128 * 1024,
				   IORESOURCE_MEM_WRITEABLE);

	armlinux_set_bootparams((void *)0x80000100);
	armlinux_set_architecture(MACH_TYPE_TX25);
	armlinux_set_serial(imx_uid());

	return 0;
}
开发者ID:AshishNamdev，项目名称:barebox，代码行数:27，代码来源:board.c

示例5: at91sam9260ek_devices_init

static int at91sam9260ek_devices_init(void)
{
	ek_add_device_nand();
	at91sam9260ek_phy_reset();
	at91_add_device_eth(0, &macb_pdata);
	at91_add_device_usbh_ohci(&ek_usbh_data);
	at91_add_device_udc(&ek_udc_data);
	ek_usb_add_device_mci();
	ek_add_device_buttons();
	ek_add_led();

	armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
	ek_set_board_type();

	devfs_add_partition("nand0", 0x00000, SZ_128K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
	dev_add_bb_dev("at91bootstrap_raw", "at91bootstrap");
	devfs_add_partition("nand0", SZ_128K, SZ_256K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_256K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
	devfs_add_partition("nand0", SZ_512K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
	dev_add_bb_dev("env_raw1", "env1");

	return 0;
}
开发者ID:RobertCNelson，项目名称:barebox-boards，代码行数:25，代码来源:init.c

示例6: at91sam9n12ek_devices_init

static int at91sam9n12ek_devices_init(void)
{
	ek_add_device_spi();
	ek_add_device_nand();
	ek_add_device_mci();
	ek_add_led();
	at91_add_device_udc(&ek_udc_data);
	ek_add_device_i2c();
	ek_add_device_ks8851();
	ek_add_device_buttons();
	ek_add_device_lcdc();

	armlinux_set_architecture(CONFIG_MACH_AT91SAM9N12EK);

	devfs_add_partition("nand0", 0x00000, SZ_256K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
	dev_add_bb_dev("at91bootstrap_raw", "at91bootstrap");
	devfs_add_partition("nand0", SZ_256K, SZ_256K + SZ_128K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_512K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
	devfs_add_partition("nand0", SZ_512K + SZ_256K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
	dev_add_bb_dev("env_raw1", "env1");

	return 0;
}
开发者ID:cuijfboy，项目名称:barebox，代码行数:25，代码来源:init.c

示例7: at91sam9x5ek_devices_init

static int at91sam9x5ek_devices_init(void)
{
	ek_add_device_w1();
	ek_add_device_nand();
	ek_add_device_eth();
	ek_add_device_spi();
	ek_add_device_mci();
	ek_add_device_usb();
	ek_add_led();
	ek_add_device_i2c();
	ek_add_device_lcdc();

	armlinux_set_architecture(CONFIG_MACH_AT91SAM9X5EK);

	devfs_add_partition("nand0", 0x00000, SZ_256K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
	dev_add_bb_dev("at91bootstrap_raw", "at91bootstrap");
	devfs_add_partition("nand0", SZ_256K, SZ_256K + SZ_128K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_512K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
	devfs_add_partition("nand0", SZ_512K + SZ_256K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
	dev_add_bb_dev("env_raw1", "env1");

	if (IS_ENABLED(CONFIG_DEFAULT_ENVIRONMENT_GENERIC))
		defaultenv_append_directory(defaultenv_at91sam9x5ek);

	return 0;
}
开发者ID:Tractorfirmware，项目名称:barebox，代码行数:28，代码来源:init.c

示例8: cupid_devices_init

static int cupid_devices_init(void)
{
	uint32_t reg;

	gpio_direction_output(GPIO_LCD_ENABLE, 0);
	gpio_direction_output(GPIO_LCD_BACKLIGHT, 0);

	reg = readl(IMX_CCM_BASE + CCM_RCSR);
	/* some fuses provide us vital information about connected hardware */
	if (reg & 0x20000000)
		nand_info.width = 2;    /* 16 bit */
	else
		nand_info.width = 1;    /* 8 bit */

	imx35_add_fec(&fec_info);
	imx35_add_nand(&nand_info);

	devfs_add_partition("nand0", 0x00000, 0x40000, PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", 0x40000, 0x80000, PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	imx35_add_fb(&ipu_fb_data);
	imx35_add_mmc0(NULL);

	armlinux_set_bootparams((void *)0x80000100);
	armlinux_set_architecture(MACH_TYPE_GUF_CUPID);

	return 0;
}
开发者ID:prpplague，项目名称:das_oszi_barebox，代码行数:30，代码来源:board.c

示例9: devices_init

static int devices_init (void)
{
	struct stat s;
	int ret;

	/*
	 * Flash can be 16MB or 32MB, setup for the last 32MB no matter
	 * what we find later.
	 */
	mpc5200_setup_cs(MPC5200_BOOTCS, 0xfe000000, SZ_32M, 0x0008fd00);
	add_cfi_flash_device(DEVICE_ID_DYNAMIC, 0xfe000000, 32 * 1024 * 1024, 0);

	add_generic_device("fec_mpc5xxx", DEVICE_ID_DYNAMIC, NULL, MPC5XXX_FEC, 0x200,
			   IORESOURCE_MEM, &fec_info);
	i2c_register_board_info(0, pcm030_i2c_devices, ARRAY_SIZE(pcm030_i2c_devices));
	add_generic_device("i2c-fsl", DEVICE_ID_DYNAMIC, NULL, MPC5XXX_I2C2, 0x100,
			IORESOURCE_MEM, &pcm030_i2c_plat);

	ret = stat("/dev/nor0", &s);
	if (ret)
		return 0;

	devfs_add_partition("nor0", s.st_size - SZ_1M, SZ_512K, DEVFS_PARTITION_FIXED, "self0");
	devfs_add_partition("nor0", s.st_size - SZ_512K, SZ_512K, DEVFS_PARTITION_FIXED, "env0");

	return 0;
}
开发者ID:jiangxilong，项目名称:barebox，代码行数:27，代码来源:pcm030.c

示例10: f3s_part_init

static int f3s_part_init(void)
{
	devfs_add_partition("disk0", 0x00000, 0x40000, PARTITION_FIXED, "self0");
	devfs_add_partition("disk0", 0x40000, 0x20000, PARTITION_FIXED, "env0");

	return 0;
}
开发者ID:cpdesign，项目名称:barebox，代码行数:7，代码来源:board.c

示例11: ep93xx_devices_init

static int ep93xx_devices_init(void)
{
	add_cfi_flash_device(DEVICE_ID_DYNAMIC, 0x60000000, EDB93XX_CFI_FLASH_SIZE, 0);

	/*
	 * Create partitions that should be
	 * not touched by any regular user
	 */
	devfs_add_partition("nor0", 0x00000, 0x40000, DEVFS_PARTITION_FIXED, "self0");
	devfs_add_partition("nor0", 0x40000, 0x20000, DEVFS_PARTITION_FIXED, "env0");

	protect_file("/dev/env0", 1);

	/*
	 * Up to 32MiB NOR type flash, connected to
	 * CS line 6, data width is 16 bit
	 */
	add_generic_device("ep93xx_eth", DEVICE_ID_DYNAMIC, NULL, 0, 0, IORESOURCE_MEM,
			NULL);

	armlinux_set_bootparams((void *)CONFIG_EP93XX_SDRAM_BANK0_BASE + 0x100);

	armlinux_set_architecture(MACH_TYPE);

	return 0;
}
开发者ID:Jokymon，项目名称:barebox，代码行数:26，代码来源:edb93xx.c

示例12: at91sam9m10ihd_devices_init

static int at91sam9m10ihd_devices_init(void)
{
	ek_add_device_w1();
	ek_add_device_nand();
	ek_add_device_eth();
	ek_add_device_mci();
	ek_add_device_spi();
	ek_add_device_i2c();
	ek_add_device_usb();
	ek_add_device_lcd();

	devfs_add_partition("nand0", 0x00000, SZ_128K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
	dev_add_bb_dev("at91bootstrap_raw", "at91bootstrap");
	devfs_add_partition("nand0", SZ_128K, SZ_256K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_256K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
	devfs_add_partition("nand0", SZ_512K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
	dev_add_bb_dev("env_raw1", "env1");

	/*
	 * The internal Atmel kernel use the SAM9M10G45EK machine id
	 * The mainline use DT
	 */
	armlinux_set_architecture(MACH_TYPE_AT91SAM9M10G45EK);

	return 0;
}
开发者ID:AubrCool，项目名称:barebox，代码行数:28，代码来源:init.c

示例13: scb9328_devices_init

static int scb9328_devices_init(void)
{
	int i;

	imx_gpio_mode(PA23_PF_CS5);
	imx_gpio_mode(GPIO_PORTB | GPIO_GPIO | GPIO_OUT | 21);
	imx_gpio_mode(GPIO_PORTB | GPIO_GPIO | GPIO_OUT | 22);
	imx_gpio_mode(GPIO_PORTB | GPIO_GPIO | GPIO_OUT | 23);
	imx_gpio_mode(GPIO_PORTB | GPIO_GPIO | GPIO_OUT | 24);

	for (i = 0; i < ARRAY_SIZE(leds); i++)
		led_gpio_register(&leds[i]);

	/* CS3 becomes CS3 by clearing reset default bit 1 in FMCR */
	writel(0x1, MX1_SCM_BASE_ADDR + MX1_FMCR);

	imx1_setup_eimcs(0, 0x000F2000, 0x11110d01);
	imx1_setup_eimcs(1, 0x000F0a00, 0x11110601);
	imx1_setup_eimcs(3, 0x000FFFFF, 0x00000303);
	imx1_setup_eimcs(4, 0x000F0a00, 0x11110301);
	imx1_setup_eimcs(5, 0x00008400, 0x00000D03);

	add_cfi_flash_device(DEVICE_ID_DYNAMIC, 0x10000000, 16 * 1024 * 1024, 0);
	add_dm9000_device(DEVICE_ID_DYNAMIC, 0x16000000, 0x16000004,
			  IORESOURCE_MEM_16BIT, &dm9000_data);

	devfs_add_partition("nor0", 0x00000, 0x40000, DEVFS_PARTITION_FIXED, "self0");
	devfs_add_partition("nor0", 0x40000, 0x20000, DEVFS_PARTITION_FIXED, "env0");
	protect_file("/dev/env0", 1);

	armlinux_set_bootparams((void *)0x08000100);
	armlinux_set_architecture(MACH_TYPE_SCB9328);

	return 0;
}
开发者ID:Reggi3，项目名称:mini210s-barebox，代码行数:35，代码来源:scb9328.c

示例14: nhk8815_devices_init

static int nhk8815_devices_init(void)
{
	st8815_add_device_sdram(64 * 1024 *1024);

	writel(0xC37800F0, NOMADIK_GPIO1_BASE + 0x20);
	writel(0x00000000, NOMADIK_GPIO1_BASE + 0x24);
	writel(0x00000000, NOMADIK_GPIO1_BASE + 0x28);
	writel(readl(NOMADIK_SRC_BASE) | 0x8000, NOMADIK_SRC_BASE);

	/* Set up SMCS1 for Ethernet: sram-like, enabled, timing values */
	writel(0x0000305b, FSMC_BCR(1));
	writel(0x00033f33, FSMC_BTR(1));

	register_device(&nhk8815_network_dev);

	register_device(&nhk8815_nand_device);

	armlinux_set_architecture(MACH_TYPE_NOMADIK);
	armlinux_set_bootparams((void *)(0x00000100));

	devfs_add_partition("nand0", 0x0000000, 0x040000, PARTITION_FIXED, "xloader_raw");
	devfs_add_partition("nand0", 0x0040000, 0x080000, PARTITION_FIXED, "meminit_raw");
	devfs_add_partition("nand0", 0x0080000, 0x200000, PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", 0x7FE0000, 0x020000, PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	return 0;
}
开发者ID:ray650128，项目名称:barebox-sh4-nextvod，代码行数:29，代码来源:setup.c

示例15: at91sam9261ek_devices_init

static int at91sam9261ek_devices_init(void)
{

	ek_add_device_nand();
	ek_add_device_dm9000();
	ek_add_device_udc();
	ek_add_device_buttons();
	ek_device_add_leds();

	devfs_add_partition("nand0", 0x00000, SZ_128K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
	devfs_add_partition("nand0", SZ_128K, SZ_256K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_256K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
	devfs_add_partition("nand0", SZ_512K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
	dev_add_bb_dev("env_raw1", "env1");

	armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
	if (machine_is_at91sam9g10ek())
		armlinux_set_architecture(MACH_TYPE_AT91SAM9G10EK);
	else
		armlinux_set_architecture(MACH_TYPE_AT91SAM9261EK);

	return 0;
}
开发者ID:cyox93，项目名称:barebox，代码行数:25，代码来源:init.c


注：本文中的devfs_add_partition函数示例由纯净天空整理自Github/MSDocs等开源代码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。