当前位置: 首页>>代码示例>>C++>>正文

C++ cpu_is_mx6q函数代码示例

本文整理汇总了C++中cpu_is_mx6q函数的典型用法代码示例。如果您正苦于以下问题：C++ cpu_is_mx6q函数的具体用法？C++ cpu_is_mx6q怎么用？C++ cpu_is_mx6q使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。


在下文中一共展示了cpu_is_mx6q函数的15个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于系统推荐出更棒的C++代码示例。

示例1: busfreq_init

static int __init busfreq_init(void)
{
	if (platform_driver_register(&busfreq_driver) != 0) {
		printk(KERN_ERR "busfreq_driver register failed\n");
		return -ENODEV;
	}

	printk(KERN_INFO "Bus freq driver module loaded\n");

#ifdef CONFIG_MX6_VPU_352M
	if (cpu_is_mx6q())
		bus_freq_scaling_is_active = 0;/*disable bus_freq*/

#else
	/* Enable busfreq by default. */
	bus_freq_scaling_is_active = 1;
#endif
	if (cpu_is_mx6q())
		set_high_bus_freq(1);
	else if (cpu_is_mx6dl())
		set_high_bus_freq(0);

	printk(KERN_INFO "Bus freq driver Enabled\n");
	return 0;
}
开发者ID:brunotl，项目名称:kernel-kobo-mx6sl-ntx，代码行数:25，代码来源:bus_freq.c

示例2: ov5640_mipi_camera_io_init

static void ov5640_mipi_camera_io_init(void)
{
	struct clk *clko1;
	
	if (cpu_is_mx6q())
	{
		mxc_iomux_v3_setup_pad(MX6Q_PAD_CSI0_MCLK__CCM_CLKO);
		mxc_iomux_v3_setup_pad(MX6Q_PAD_CSI0_DAT18__GPIO_6_4);
	}
	else
	{
		mxc_iomux_v3_setup_pad(MX6DL_PAD_CSI0_MCLK__CCM_CLKO);
		mxc_iomux_v3_setup_pad(MX6DL_PAD_CSI0_DAT18__GPIO_6_4);
	}
	
	clko1 = clk_get(NULL, "clko_clk");
	if (IS_ERR(clko1)) {
		pr_err("can't get CLKO1 clock.\n");
	} else {
		long round = clk_round_rate(clko1, 27000000);
		clk_set_rate(clko1, round);
		clk_enable(clko1);
	}
	
	/* Camera reset */
	gpio_request(MX6_CAMERA_RST, "cam-reset");
	gpio_direction_output(MX6_CAMERA_RST, 0);
	msleep(1);
	gpio_set_value(MX6_CAMERA_RST, 1);
	msleep(100);
	
/* for mx6dl, mipi virtual channel 1 connect to csi 0*/
	if (cpu_is_mx6dl())
		mxc_iomux_set_gpr_register(13, 0, 3, 0);	
}
开发者ID:pacificIT，项目名称:udoo_kernel_imx，代码行数:35，代码来源:board-mx6_udoo.c

示例3: imx6_mmu_init

static int imx6_mmu_init(void)
{
    void __iomem *l2x0_base = IOMEM(0x00a02000);
    u32 val;

    if (!cpu_is_mx6())
        return 0;

    /* Configure the L2 PREFETCH and POWER registers */
    val = readl(l2x0_base + L310_PREFETCH_CTRL);
    val |= 0x70800000;

    /*
     * The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
     * The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
     * But according to ARM PL310 errata: 752271
     * ID: 752271: Double linefill feature can cause data corruption
     * Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
     * Workaround: The only workaround to this erratum is to disable the
     * double linefill feature. This is the default behavior.
     */
    if (cpu_is_mx6q())
        val &= ~(1 << 30 | 1 << 23);

    writel(val, l2x0_base + L310_PREFETCH_CTRL);

    l2x0_init(l2x0_base, 0x0, ~0UL);

    return 0;
}
开发者ID:jcobham，项目名称:barebox，代码行数:30，代码来源:imx6.c

示例4: mx6q_csi0_io_init

static void mx6q_csi0_io_init(void)
{
	if (cpu_is_mx6q())
		mxc_iomux_set_gpr_register(1, 19, 1, 1);
	else if (cpu_is_mx6dl())
		mxc_iomux_set_gpr_register(13, 0, 3, 4);
}
开发者ID:Electrongod1966，项目名称:mx6-wandboard，代码行数:7，代码来源:board-mx6q_sabreauto.c

示例5: if

struct cpu_op *mx6_get_cpu_op(int *op)
{
	if (cpu_is_mx6dl()) {
		if (arm_max_freq == CPU_AT_1_2GHz) {
			*op =  num_cpu_op = ARRAY_SIZE(mx6dl_cpu_op_1_2G);
			return mx6dl_cpu_op_1_2G;
		} else if (arm_max_freq == CPU_AT_1GHz) {
			*op =  num_cpu_op = ARRAY_SIZE(mx6dl_cpu_op_1G);
			return mx6dl_cpu_op_1G;
		} else {
			*op =  num_cpu_op = ARRAY_SIZE(mx6dl_cpu_op);
			return mx6dl_cpu_op;
		}
	} else if (cpu_is_mx6q()) {
		if (arm_max_freq == CPU_AT_1_2GHz) {
			*op =  num_cpu_op = ARRAY_SIZE(mx6q_cpu_op_1_2G);
			return mx6q_cpu_op_1_2G;
		} else if (arm_max_freq == CPU_AT_1GHz) {
			*op =  num_cpu_op = ARRAY_SIZE(mx6q_cpu_op_1G);
			return mx6q_cpu_op_1G;
		} else {
			*op =  num_cpu_op = ARRAY_SIZE(mx6q_cpu_op);
			return mx6q_cpu_op;
		}
	} else {
		if (arm_max_freq == CPU_AT_1GHz) {
			*op =  num_cpu_op = ARRAY_SIZE(mx6sl_cpu_op_1G);
			return mx6sl_cpu_op_1G;
		} else {
			*op =  num_cpu_op = ARRAY_SIZE(mx6sl_cpu_op);
			return mx6sl_cpu_op;
		}
	}
}
开发者ID:billysmith，项目名称:linux-imx-wandboard，代码行数:34，代码来源:cpu_op-mx6.c

示例6: bus_freq_scaling_enable_store

static ssize_t bus_freq_scaling_enable_store(struct device *dev,
				 struct device_attribute *attr,
				 const char *buf, size_t size)
{
	if (strncmp(buf, "1", 1) == 0) {
#ifdef CONFIG_MX6_VPU_352M
		if (cpu_is_mx6q())
			/*do not enable bus freq*/
			bus_freq_scaling_is_active = 0;
		printk(KERN_WARNING "Bus frequency can't be enabled if using VPU 352M!\n");
		return size;
#else
		bus_freq_scaling_is_active = 1;
#endif
		set_high_bus_freq(0);
		/* Make sure system can enter low bus mode if it should be in
		low bus mode */
		if (low_freq_bus_used() && !low_bus_freq_mode)
			set_low_bus_freq();
	} else if (strncmp(buf, "0", 1) == 0) {
		if (bus_freq_scaling_is_active)
			set_high_bus_freq(1);
		bus_freq_scaling_is_active = 0;
	}
	return size;
}
开发者ID:brunotl，项目名称:kernel-kobo-mx6sl-ntx，代码行数:26，代码来源:bus_freq.c

示例7: arch_idle_multi_core

void arch_idle_multi_core(void)
{
	u32 reg;
	int cpu = smp_processor_id();

#ifdef CONFIG_LOCAL_TIMERS
	if (!tick_broadcast_oneshot_active()
		|| !tick_oneshot_mode_active())
		return;

	clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &cpu);
#endif
	/* iMX6Q and iMX6DL */
	if ((cpu_is_mx6q() && chip_rev >= IMX_CHIP_REVISION_1_2) ||
		(cpu_is_mx6dl() && chip_rev >= IMX_CHIP_REVISION_1_1)) {
		/*
		  * This code should only be executed on MX6QTO1.2 or later
		  * and MX6DL TO1.1 or later.
		  * These chips have the HW fix for the WAIT mode issue.
		  * Ensure that the CGPR bit 17 is set to enable the fix.
		  */

		reg = __raw_readl(MXC_CCM_CGPR);
		reg |= MXC_CCM_CGPR_WAIT_MODE_FIX;
		__raw_writel(reg, MXC_CCM_CGPR);

		ca9_do_idle();
	} else
		arch_idle_with_workaround(cpu);
#ifdef CONFIG_LOCAL_TIMERS
	clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT, &cpu);
#endif

}
开发者ID:Electrongod1966，项目名称:mx6-wandboard，代码行数:34，代码来源:system.c

示例8: mx6_usb_h2_init

void __init mx6_usb_h2_init(void)
{
	struct platform_device *pdev, *pdev_wakeup;
	static void __iomem *anatop_base_addr = MX6_IO_ADDRESS(ANATOP_BASE_ADDR);
	usbh2_config.wakeup_pdata = &usbh2_wakeup_config;

	hsic_strobe_start_pad = cpu_is_mx6q() ? MX6Q_PAD_RGMII_TX_CTL__USBOH3_H2_STROBE_START :
			(cpu_is_mx6dl() ? MX6DL_PAD_RGMII_TX_CTL__USBOH3_H2_STROBE_START :
			(cpu_is_mx6sl() ? MX6SL_PAD_HSIC_STROBE__USB_H_STROBE_START : 0));

	if (cpu_is_mx6sl())
		pdev = imx6sl_add_fsl_ehci_hs(2, &usbh2_config);
	else
		pdev = imx6q_add_fsl_ehci_hs(2, &usbh2_config);

	usbh2_wakeup_config.usb_pdata[0] = pdev->dev.platform_data;
	if (cpu_is_mx6sl())
		pdev_wakeup = imx6sl_add_fsl_usb2_hs_wakeup(2, &usbh2_wakeup_config);
	else
		pdev_wakeup = imx6q_add_fsl_usb2_hs_wakeup(2, &usbh2_wakeup_config);
	platform_device_add(pdev);
	((struct fsl_usb2_platform_data *)(pdev->dev.platform_data))->wakeup_pdata =
		pdev_wakeup->dev.platform_data;
	/* Some phy and power's special controls for host2
	 * 1. Its 480M is from OTG's 480M
	 * 2. EN_USB_CLKS should always be opened
	 */
	__raw_writel(BM_ANADIG_USB1_PLL_480_CTRL_EN_USB_CLKS,
			anatop_base_addr + HW_ANADIG_USB1_PLL_480_CTRL_SET);
	/* must change the clkgate delay to 2 or 3 to avoid
	 * 24M OSCI clock not stable issue */
	__raw_writel(BF_ANADIG_ANA_MISC0_CLKGATE_DELAY(3),
			anatop_base_addr + HW_ANADIG_ANA_MISC0);
}
开发者ID:videologyincengineering，项目名称:TFMIPI_Kernel，代码行数:34，代码来源:usb_h2.c

示例9: wand_mux_pads_init_ipu2_lcd0

void wand_mux_pads_init_ipu2_lcd0(void)
{
	if (!cpu_is_mx6q())
		return;

	mxc_iomux_v3_setup_pad(MX6Q_PAD_DI0_DISP_CLK__IPU2_DI0_DISP_CLK);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DI0_PIN2__IPU2_DI0_PIN2);		// HSync 
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DI0_PIN3__IPU2_DI0_PIN3);		// VSync 
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DI0_PIN4__IPU2_DI0_PIN4);		// Contrast 
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DI0_PIN15__IPU2_DI0_PIN15);		// DISP0_DRDY 
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT0__IPU2_DISP0_DAT_0);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT1__IPU2_DISP0_DAT_1);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT2__IPU2_DISP0_DAT_2);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT3__IPU2_DISP0_DAT_3);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT4__IPU2_DISP0_DAT_4);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT5__IPU2_DISP0_DAT_5);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT6__IPU2_DISP0_DAT_6);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT7__IPU2_DISP0_DAT_7);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT8__IPU2_DISP0_DAT_8);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT9__IPU2_DISP0_DAT_9);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT10__IPU2_DISP0_DAT_10);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT11__IPU2_DISP0_DAT_11);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT12__IPU2_DISP0_DAT_12);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT13__IPU2_DISP0_DAT_13);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT14__IPU2_DISP0_DAT_14);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT15__IPU2_DISP0_DAT_15);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT16__IPU2_DISP0_DAT_16);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT17__IPU2_DISP0_DAT_17);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT18__IPU2_DISP0_DAT_18);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT19__IPU2_DISP0_DAT_19);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT20__IPU2_DISP0_DAT_20);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT21__IPU2_DISP0_DAT_21);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT22__IPU2_DISP0_DAT_22);
	mxc_iomux_v3_setup_pad(MX6Q_PAD_DISP0_DAT23__IPU2_DISP0_DAT_23);
}
开发者ID:tkurbad，项目名称:wandboard，代码行数:35，代码来源:board-wand-mux.c

示例10: plt_sd_pad_change

static int plt_sd_pad_change(unsigned int index, int clock)
{
	/* LOW speed is the default state of SD pads */
	static enum sd_pad_mode pad_mode = SD_PAD_MODE_LOW_SPEED;

	iomux_v3_cfg_t *sd_pads_200mhz = NULL;
	iomux_v3_cfg_t *sd_pads_100mhz = NULL;
	iomux_v3_cfg_t *sd_pads_50mhz = NULL;

	u32 sd_pads_200mhz_cnt;
	u32 sd_pads_100mhz_cnt;
	u32 sd_pads_50mhz_cnt;

	if (index != 2) {
		printk(KERN_ERR"no such SD host controller index %d\n", index);
		return -EINVAL;
	}

	if (cpu_is_mx6q()) {
		sd_pads_200mhz = mx6q_sd3_200mhz;
		sd_pads_100mhz = mx6q_sd3_100mhz;
		sd_pads_50mhz = mx6q_sd3_50mhz;

		sd_pads_200mhz_cnt = ARRAY_SIZE(mx6q_sd3_200mhz);
		sd_pads_100mhz_cnt = ARRAY_SIZE(mx6q_sd3_100mhz);
		sd_pads_50mhz_cnt = ARRAY_SIZE(mx6q_sd3_50mhz);
	} else if (cpu_is_mx6dl()) {
		sd_pads_200mhz = mx6dl_sd3_200mhz;
		sd_pads_100mhz = mx6dl_sd3_100mhz;
		sd_pads_50mhz = mx6dl_sd3_50mhz;

		sd_pads_200mhz_cnt = ARRAY_SIZE(mx6dl_sd3_200mhz);
		sd_pads_100mhz_cnt = ARRAY_SIZE(mx6dl_sd3_100mhz);
		sd_pads_50mhz_cnt = ARRAY_SIZE(mx6dl_sd3_50mhz);
	}

	if (clock > 100000000) {
		if (pad_mode == SD_PAD_MODE_HIGH_SPEED)
			return 0;
		BUG_ON(!sd_pads_200mhz);
		pad_mode = SD_PAD_MODE_HIGH_SPEED;
		return mxc_iomux_v3_setup_multiple_pads(sd_pads_200mhz,
							sd_pads_200mhz_cnt);
	} else if (clock > 52000000) {
		if (pad_mode == SD_PAD_MODE_MED_SPEED)
			return 0;
		BUG_ON(!sd_pads_100mhz);
		pad_mode = SD_PAD_MODE_MED_SPEED;
		return mxc_iomux_v3_setup_multiple_pads(sd_pads_100mhz,
							sd_pads_100mhz_cnt);
	} else {
		if (pad_mode == SD_PAD_MODE_LOW_SPEED)
			return 0;
		BUG_ON(!sd_pads_50mhz);
		pad_mode = SD_PAD_MODE_LOW_SPEED;
		return mxc_iomux_v3_setup_multiple_pads(sd_pads_50mhz,
							sd_pads_50mhz_cnt);
	}
}
开发者ID:rogrady，项目名称:lin_imx6，代码行数:59，代码来源:board-mx6q_sabreauto.c

示例11: adv7180_io_init

static void adv7180_io_init(void)
{
	camera_reset(IMX_GPIO_NR(3, 13), 0, IMX_GPIO_NR(3, 14), -1);

	if (cpu_is_mx6q())
		mxc_iomux_set_gpr_register(1, 20, 1, 1);
	else
		mxc_iomux_set_gpr_register(13, 3, 3, 4);
}
开发者ID:blacktigersoftware，项目名称:hummingboard-cuboxi-kernel，代码行数:9，代码来源:board-mx6_nitrogen6x.c

示例12: reduce_bus_freq_handler

static void reduce_bus_freq_handler(struct work_struct *work)
{
    unsigned long reg;

    if (low_bus_freq_mode || !low_freq_bus_used())
        return;

    if (audio_bus_freq_mode && lp_audio_freq)
        return;

    while (!mutex_trylock(&bus_freq_mutex))
        msleep(1);

    /* PLL3 is used in the DDR freq change process, enable it. */

    if (low_bus_freq_mode || !low_freq_bus_used()) {
        mutex_unlock(&bus_freq_mutex);
        return;
    }

    if (audio_bus_freq_mode && lp_audio_freq) {
        mutex_unlock(&bus_freq_mutex);
        return;
    }

    clk_enable(pll3);

    if (lp_audio_freq) {
        /* Need to ensure that PLL2_PFD_400M is kept ON. */
        clk_enable(pll2_400);
        update_ddr_freq(50000000);
        audio_bus_freq_mode = 1;
        low_bus_freq_mode = 0;
    } else {
        update_ddr_freq(24000000);
        if (audio_bus_freq_mode)
            clk_disable(pll2_400);
        low_bus_freq_mode = 1;
        audio_bus_freq_mode = 0;
    }

    if (med_bus_freq_mode)
        clk_disable(pll2_400);

    high_bus_freq_mode = 0;
    med_bus_freq_mode = 0;

    if (cpu_is_mx6q()) {
        /* Power gate the PU LDO. */
        org_ldo = reg = __raw_readl(ANADIG_REG_CORE);
        reg &= ~(ANADIG_REG_TARGET_MASK << ANADIG_REG1_PU_TARGET_OFFSET);
        __raw_writel(reg, ANADIG_REG_CORE);
    }
    clk_disable(pll3);
    mutex_unlock(&bus_freq_mutex);

}
开发者ID:jeremyhammer，项目名称:imx6_linux，代码行数:57，代码来源:bus_freq.c

示例13: mx6q_revision

/*
 * Returns:
 *	the silicon revision of the cpu
 *	-EINVAL - not a mx50
 */
int mx6q_revision(void)
{
	if (!cpu_is_mx6q())
		return -EINVAL;

	if (cpu_silicon_rev == -1)
		cpu_silicon_rev = get_mx6q_srev();

	return cpu_silicon_rev;
}
开发者ID:boseji，项目名称:kernel_imx，代码行数:15，代码来源:cpu.c

示例14: hsic_start

static void hsic_start(void)
{
	pr_debug("%s", __func__);
	/* strobe 47K pull up */
	if (cpu_is_mx6q())
		mxc_iomux_v3_setup_pad(
				MX6Q_PAD_RGMII_RXC__USBOH3_H3_STROBE_START);
	else if (cpu_is_mx6dl())
		mxc_iomux_v3_setup_pad(
				MX6DL_PAD_RGMII_RXC__USBOH3_H3_STROBE_START);
}
开发者ID:brunotl，项目名称:kernel-kobo-mx6sl-ntx，代码行数:11，代码来源:usb_h3.c

示例15: plt_sd3_pad_change

static int plt_sd3_pad_change(int clock) {
	static enum sd_pad_mode pad_mode = SD_PAD_MODE_LOW_SPEED;

	if (clock > 100000000) {
		if (pad_mode == SD_PAD_MODE_HIGH_SPEED)
			return 0;

		pad_mode = SD_PAD_MODE_HIGH_SPEED;
		if (cpu_is_mx6q()) {
			return mxc_iomux_v3_setup_multiple_pads(mx6q_sd3_200mhz,
						ARRAY_SIZE(mx6dl_sd3_200mhz));
		} else if (cpu_is_mx6dl()) {
			return mxc_iomux_v3_setup_multiple_pads(mx6dl_sd3_200mhz,
						ARRAY_SIZE(mx6dl_sd3_200mhz));
		}
	} else if (clock > 52000000) {
		if (pad_mode == SD_PAD_MODE_MED_SPEED)
			return 0;

		pad_mode = SD_PAD_MODE_MED_SPEED;
		if (cpu_is_mx6q()) {
			return mxc_iomux_v3_setup_multiple_pads(mx6q_sd3_100mhz,
						ARRAY_SIZE(mx6dl_sd3_200mhz));
		} else if (cpu_is_mx6dl()) {
			return mxc_iomux_v3_setup_multiple_pads(mx6dl_sd3_100mhz,
						ARRAY_SIZE(mx6dl_sd3_200mhz));
		}
	} else {
		if (pad_mode == SD_PAD_MODE_LOW_SPEED)
			return 0;

		pad_mode = SD_PAD_MODE_LOW_SPEED;
		if (cpu_is_mx6q()) {
			return mxc_iomux_v3_setup_multiple_pads(mx6q_sd3_50mhz,
						ARRAY_SIZE(mx6dl_sd3_200mhz));
		} else if (cpu_is_mx6dl()) {
			return mxc_iomux_v3_setup_multiple_pads(mx6dl_sd3_50mhz,
						ARRAY_SIZE(mx6dl_sd3_200mhz));
		}
	}
}
开发者ID:sncn-private，项目名称:imx6-linux，代码行数:41，代码来源:board-mx6_seco_uSBC.c


注：本文中的cpu_is_mx6q函数示例由纯净天空整理自Github/MSDocs等开源代码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。