C++ READ_PERI_REG函数代码示例

void pin_set(uint pin, int value) {
    if (pin == 16) {
        int out_en = (pin_mode[pin] == GPIO_MODE_OUTPUT);
        WRITE_PERI_REG(PAD_XPD_DCDC_CONF, (READ_PERI_REG(PAD_XPD_DCDC_CONF) & 0xffffffbc) | 1);
        WRITE_PERI_REG(RTC_GPIO_CONF, READ_PERI_REG(RTC_GPIO_CONF) & ~1);
        WRITE_PERI_REG(RTC_GPIO_ENABLE, (READ_PERI_REG(RTC_GPIO_ENABLE) & ~1) | out_en);
        WRITE_PERI_REG(RTC_GPIO_OUT, (READ_PERI_REG(RTC_GPIO_OUT) & ~1) | value);
        return;
    }

    uint32_t enable = 0;
    uint32_t disable = 0;
    switch (pin_mode[pin]) {
        case GPIO_MODE_INPUT:
            value = -1;
            disable = 1;
            break;

        case GPIO_MODE_OUTPUT:
            enable = 1;
            break;

        case GPIO_MODE_OPEN_DRAIN:
            if (value == -1) {
                return;
            } else if (value == 0) {
                enable = 1;
            } else {
                value = -1;
                disable = 1;
            }
            break;
    }

    enable <<= pin;
    disable <<= pin;
    if (value == -1) {
        gpio_output_set(0, 0, enable, disable);
    } else {
        gpio_output_set(value << pin, (1 - value) << pin, enable, disable);
    }
}

IRAM NOINSTR static void rx_isr(void *param) {
  /* TODO(alashkin): add errors checking */
  unsigned int peri_reg = READ_PERI_REG(UART_INTR_STATUS(UART_MAIN));
  static volatile int tail = 0;
  (void) param;

  if ((peri_reg & UART_RXBUF_FULL) != 0 || (peri_reg & UART_RX_NEW) != 0) {
    int char_count, i;
    CLEAR_PERI_REG_MASK(UART_CTRL_INTR(UART_MAIN),
                        UART_RXBUF_FULL | UART_RX_NEW);
    WRITE_PERI_REG(UART_CLEAR_INTR(UART_MAIN), UART_RXBUF_FULL | UART_RX_NEW);

    char_count = READ_PERI_REG(UART_DATA_STATUS(UART_MAIN)) & 0x000000FF;

    /* TODO(mkm): handle overrun */
    for (i = 0; i < char_count; i++) {
      char ch = READ_PERI_REG(UART_BUF(UART_MAIN)) & 0xFF;
      if (s_custom_callback != NULL) {
        s_custom_callback(ch);
      } else {
        rx_buf[tail] = ch;
        if (rx_buf[tail] == UART_SIGINT_CHAR && uart_interrupt_cb) {
          /* swallow the intr byte */
          tail = (tail - 1) % RX_BUFFER_SIZE;
          uart_interrupt_cb(UART_SIGINT_CHAR);
        }
        tail = (tail + 1) % RX_BUFFER_SIZE;
      }
    }

    WRITE_PERI_REG(UART_CLEAR_INTR(UART_MAIN), UART_RXBUF_FULL | UART_RX_NEW);
    SET_PERI_REG_MASK(UART_CTRL_INTR(UART_MAIN), UART_RXBUF_FULL | UART_RX_NEW);

    if (s_custom_callback == NULL) {
#ifndef RTOS_SDK
      system_os_post(TASK_PRIORITY, 0, tail);
#else
      rtos_dispatch_char_handler(tail);
#endif
    }
  }
}

void esp_uart_print_status(void *arg) {
  struct esp_uart_state *us = (struct esp_uart_state *) arg;
  struct esp_uart_stats *s = &us->stats;
  struct esp_uart_stats *ps = &us->prev_stats;
  int uart_no = us->cfg->uart_no;
  fprintf(
      stderr,
      "UART%d ints %u/%u/%u; rx en %d bytes %u buf %u fifo %u, ovf %u, lcs %u; "
      "tx %u %u %u, thr %u; hf %u i 0x%03x ie 0x%03x cts %d\n",
      uart_no, s->ints - ps->ints, s->rx_ints - ps->rx_ints,
      s->tx_ints - ps->tx_ints, us->rx_enabled, s->rx_bytes - ps->rx_bytes,
      us->rx_buf.used, rx_fifo_len(us->cfg->uart_no),
      s->rx_overflows - ps->rx_overflows,
      s->rx_linger_conts - ps->rx_linger_conts, s->tx_bytes - ps->tx_bytes,
      us->tx_buf.used, tx_fifo_len(us->cfg->uart_no),
      s->tx_throttles - ps->tx_throttles, system_get_free_heap_size(),
      READ_PERI_REG(UART_INT_RAW(uart_no)),
      READ_PERI_REG(UART_INT_ENA(uart_no)), cts(uart_no));
  memcpy(ps, s, sizeof(*s));
}

static void hard_i2c_stop(void)
{
	int count_ = 1000; 

  WRITE_PERI_REG(PREG_I2C_MS_TOKEN_LIST_REG0, ((I2C_END << 28)   | 
                                               (I2C_END << 24)   | 
                                               (I2C_END << 20)   |
                                               (I2C_END << 16)   |
                                               (I2C_END << 12)   |
                                               (I2C_END << 8)    |
                                               (I2C_END << 4)    |
                                               (I2C_STOP << 0)         ));       
        // Toggle start low then high 
  	WRITE_PERI_REG(PREG_I2C_MS_CTRL, ((READ_PERI_REG(PREG_I2C_MS_CTRL)) & 0xfffffffe ));         
   WRITE_PERI_REG(PREG_I2C_MS_CTRL, ((READ_PERI_REG(PREG_I2C_MS_CTRL)) | 0x1 )); 	

   while( ((READ_PERI_REG(PREG_I2C_MS_CTRL)) & (1 << I2C_M_STATUS)) && (count_ -- ));  // Wait for the transfer to complete  


}

static uint32 get_gpio16()
{
    // set output level to 1
    WRITE_PERI_REG(RTC_GPIO_OUT, (READ_PERI_REG(RTC_GPIO_OUT) & (uint32)0xfffffffe) | (uint32)(1));

    // read level
    WRITE_PERI_REG(PAD_XPD_DCDC_CONF,
        (READ_PERI_REG(PAD_XPD_DCDC_CONF) & 0xffffffbc)
            | (uint32)0x1); // mux configuration for XPD_DCDC and
    // rtc_gpio0 connection
    WRITE_PERI_REG(RTC_GPIO_CONF,
        (READ_PERI_REG(RTC_GPIO_CONF) & (uint32)0xfffffffe)
            | (uint32)0x0); // mux configuration for out enable
    WRITE_PERI_REG(
        RTC_GPIO_ENABLE, READ_PERI_REG(RTC_GPIO_ENABLE) & (uint32)0xfffffffe); // out disable

    uint32 x = (READ_PERI_REG(RTC_GPIO_IN_DATA) & 1);

    return x;
}

IRAM NOINSTR static void esp_handle_uart_int(struct esp_uart_state *us) {
  const int uart_no = us->cfg->uart_no;
  /* Since both UARTs use the same int, we need to apply the mask manually. */
  const unsigned int int_st = READ_PERI_REG(UART_INT_ST(uart_no)) &
                              READ_PERI_REG(UART_INT_ENA(uart_no));
  if (int_st == 0) return;
  us->stats.ints++;
  if (int_st & UART_RXFIFO_OVF_INT_ST) us->stats.rx_overflows++;
  if (int_st & UART_CTS_CHG_INT_ST) {
    if (cts(uart_no) != 0 && tx_fifo_len(uart_no) > 0) us->stats.tx_throttles++;
  }
  if (int_st & (UART_RX_INTS | UART_TX_INTS)) {
    if (int_st & UART_RX_INTS) us->stats.rx_ints++;
    if (int_st & UART_TX_INTS) us->stats.tx_ints++;
    /* Wake up the processor and disable TX and RX ints until it runs. */
    WRITE_PERI_REG(UART_INT_ENA(uart_no), UART_INFO_INTS);
    us->cfg->dispatch_cb(uart_no);
  }
  WRITE_PERI_REG(UART_INT_CLR(uart_no), int_st);
}

int gdb_read_uart_buf(char *buf) {
  unsigned int peri_reg = READ_PERI_REG(UART_INTR_STATUS(UART_MAIN));

  if ((peri_reg & UART_RXBUF_FULL) != 0 || (peri_reg & UART_RX_NEW) != 0) {
    int char_count, i;
    CLEAR_PERI_REG_MASK(UART_CTRL_INTR(UART_MAIN),
                        UART_RXBUF_FULL | UART_RX_NEW);
    WRITE_PERI_REG(UART_CLEAR_INTR(UART_MAIN), UART_RXBUF_FULL | UART_RX_NEW);

    char_count = READ_PERI_REG(UART_DATA_STATUS(UART_MAIN)) & 0x000000FF;

    for (i = 0; i < char_count; i++) {
      buf[i] = READ_PERI_REG(UART_BUF(UART_MAIN)) & 0xFF;
    }

    WRITE_PERI_REG(UART_CLEAR_INTR(UART_MAIN), UART_RXBUF_FULL | UART_RX_NEW);
    SET_PERI_REG_MASK(UART_CTRL_INTR(UART_MAIN), UART_RXBUF_FULL | UART_RX_NEW);
    return char_count;
  }
  return 0;
}

void mp_hal_pin_config_od(mp_hal_pin_obj_t pin_id) {
    const pyb_pin_obj_t *pin = &pyb_pin_obj[pin_id];

    if (pin->phys_port == 16) {
        // configure GPIO16 as input with output register holding 0
        WRITE_PERI_REG(PAD_XPD_DCDC_CONF, (READ_PERI_REG(PAD_XPD_DCDC_CONF) & 0xffffffbc) | 1);
        WRITE_PERI_REG(RTC_GPIO_CONF, READ_PERI_REG(RTC_GPIO_CONF) & ~1);
        WRITE_PERI_REG(RTC_GPIO_ENABLE, (READ_PERI_REG(RTC_GPIO_ENABLE) & ~1)); // input
        WRITE_PERI_REG(RTC_GPIO_OUT, (READ_PERI_REG(RTC_GPIO_OUT) & ~1)); // out=0
        return;
    }

    ETS_GPIO_INTR_DISABLE();
    PIN_FUNC_SELECT(pin->periph, pin->func);
    GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(pin->phys_port)),
        GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(pin->phys_port)))
        | GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_ENABLE)); // open drain
    GPIO_REG_WRITE(GPIO_ENABLE_ADDRESS,
        GPIO_REG_READ(GPIO_ENABLE_ADDRESS) | (1 << pin->phys_port));
    ETS_GPIO_INTR_ENABLE();
}

static void rx_buff_read_done(void)
{
    union sdio_slave_status sdio_sta;
    /////modify sdio status reg
    sdio_sta.word_value=READ_PERI_REG(SLC_HOST_CONF_W2);
    sdio_sta.elm_value.comm_cnt++;
    sdio_sta.elm_value.rd_empty=1;
    sdio_sta.elm_value.rx_length=0;
    sdio_sta.elm_value.intr_no &= (~RX_AVAILIBLE);
    WRITE_PERI_REG(SLC_HOST_CONF_W2, sdio_sta.word_value);  //update sdio status register
    //os_printf("rx_buff_read_done\r\n");
}

/**
 * Uniform way of getting GPIO input value. Handles GPIO 0-16.
 * The pin must be initiated with easygpio_pinMode() so that the pin mux is setup as a gpio in the first place.
 * If you know that you won't be using GPIO16 then you'd better off by just using GPIO_INPUT_GET().
 */
uint8_t
easygpio_inputGet(uint8_t gpio_pin) {
  if (16==gpio_pin) {
    return (READ_PERI_REG(RTC_GPIO_IN_DATA) & 1UL);
  } else {
#ifdef EASYGPIO_USE_GPIO_INPUT_GET
    return GPIO_INPUT_GET(GPIO_ID_PIN(gpio_pin));
#else
  // this does *not* work, maybe GPIO_IN_ADDRESS is the wrong address
  return ((GPIO_REG_READ(GPIO_IN_ADDRESS) > gpio_pin)  & 1UL);
#endif
  }
}

static void uartIsrHdl(void *arg)
{
    char c;
    char buf[50];
    char *item;
    int r;
    size_t len;
    BaseType_t xHigherPriorityTaskWoken;
    SET_PERI_REG_MASK(UART_INT_CLR_REG(0), UART_RXFIFO_FULL_INT_CLR);
    while (READ_PERI_REG(UART_STATUS_REG(0)) & (UART_RXFIFO_CNT << UART_RXFIFO_CNT_S)) {
        c = READ_PERI_REG(UART_FIFO_REG(0));
        if (c == 'r') {
            ets_printf("ISR r");
            xRingbufferPrintInfo(rb);
            item = xRingbufferReceiveFromISR(rb, &len);
            if (item == NULL) {
                ets_printf("ISR recv fail!\n");
            } else if (len == 0) {
                ets_printf("ISR recv NULL!\n");
                vRingbufferReturnItemFromISR(rb, item, &xHigherPriorityTaskWoken);
            } else {
                ets_printf("ISR recv '%s' (%d bytes, %p)\n", buf, len, buf);
                vRingbufferReturnItemFromISR(rb, item, &xHigherPriorityTaskWoken);
            }
        } else {
            sprintf(buf, "UART: %c", c);
            ets_printf("ISR w");
            xRingbufferPrintInfo(rb);
            r = xRingbufferSendFromISR(rb, buf, strlen(buf) + 1, &xHigherPriorityTaskWoken);
            if (!r) {
                ets_printf("ISR send fail\n");
            }
        }
    }
    if (xHigherPriorityTaskWoken) {
        portYIELD_FROM_ISR();
    }
}

IRAM bool adj_rx_fifo_full_thresh(struct mgos_uart_state *us) {
  int uart_no = us->uart_no;
  uint8_t thresh = us->cfg.dev.rx_fifo_full_thresh;
  uint8_t rx_fifo_len = esp_uart_rx_fifo_len(uart_no);
  if (rx_fifo_len >= thresh && us->cfg.rx_fc_type == MGOS_UART_FC_SW) {
    thresh = us->cfg.dev.rx_fifo_fc_thresh;
  }
  if (get_rx_fifo_full_thresh(uart_no) != thresh) {
    uint32_t conf1 = READ_PERI_REG(UART_CONF1(uart_no));
    conf1 = (conf1 & ~0x7f) | thresh;
    WRITE_PERI_REG(UART_CONF1(uart_no), conf1);
  }
  return (rx_fifo_len < thresh);
}

LOCAL void slc_isr(void) {
	//portBASE_TYPE HPTaskAwoken=0;
	struct sdio_queue *finishedDesc;
	uint32 slc_intr_status;
	int x;

	slc_intr_status = READ_PERI_REG(SLC_INT_STATUS);
	//clear all intr flags
	WRITE_PERI_REG(SLC_INT_CLR, 0xffffffff);//slc_intr_status);
	if ( (slc_intr_status & SLC_RX_EOF_INT_ST))
	{
		//The DMA subsystem is done with this block: Push it on the queue so it can be re-used.
		finishedDesc=(struct sdio_queue*)READ_PERI_REG(SLC_RX_EOF_DES_ADDR);
		curdma = (uint32_t*)finishedDesc->buf_ptr;

		//Allow signal jamming, useful for testing output.
		if( jam_color < 0 )
		{
			//*startdma = premodulated_table[0];
			int lk = 0;
			if( gline & 1 )
				lk = (CbLookup[gline>>1]>>4)&0x0f;
			else

static IRAM_ATTR void spi_intr(void *arg)
{
    spi_host_t host;
    uint32_t trans_done;

    if (READ_PERI_REG(DPORT_SPI_INT_STATUS_REG) & DPORT_SPI_INT_STATUS_SPI0) { // DPORT_SPI_INT_STATUS_SPI0
        trans_done = SPI0.slave.val & 0x1F;
        SPI0.slave.val &= ~0x3FF;
        host = CSPI_HOST;
    } else if (READ_PERI_REG(DPORT_SPI_INT_STATUS_REG) & DPORT_SPI_INT_STATUS_SPI1) { // DPORT_SPI_INT_STATUS_SPI1
        trans_done = SPI1.slave.val & 0x1F;
        SPI1.slave.val &= ~0x1F;
        host = HSPI_HOST;
    } else {
        return;
    }

    if (spi_object[host]) {
        if (spi_object[host]->event_cb) {
            spi_object[host]->event_cb(SPI_TRANS_DONE_EVENT, &trans_done);
        }
    }
}

/******************************************************************************
 * FunctionName : uart_recvTask
 * Description  : system task triggered on receive interrupt, empties FIFO and calls callbacks
*******************************************************************************/
static void ICACHE_FLASH_ATTR
uart_recvTask(os_event_t *events)
{
  while (READ_PERI_REG(UART_STATUS(UART0)) & (UART_RXFIFO_CNT << UART_RXFIFO_CNT_S)) {
    //WRITE_PERI_REG(0X60000914, 0x73); //WTD // commented out by TvE

    // read a buffer-full from the uart
    uint16 length = 0;
    char buf[128];
    while ((READ_PERI_REG(UART_STATUS(UART0)) & (UART_RXFIFO_CNT << UART_RXFIFO_CNT_S)) &&
           (length < 128)) {
      buf[length++] = READ_PERI_REG(UART_FIFO(UART0)) & 0xFF;
    }
#ifdef UART_DBG
    os_printf("%d ix %d\n", system_get_time(), length);
#endif

    for (int i=0; i<MAX_CB; i++) {
      if (uart_recv_cb[i] != NULL) (uart_recv_cb[i])(buf, length);
    }
  }
  WRITE_PERI_REG(UART_INT_CLR(UART0), UART_RXFIFO_FULL_INT_CLR|UART_RXFIFO_TOUT_INT_CLR);
  ETS_UART_INTR_ENABLE();
}