当前位置: 首页>>代码示例>>C++>>正文

C++ OMAP3_MUX函数代码示例

本文整理汇总了C++中OMAP3_MUX函数的典型用法代码示例。如果您正苦于以下问题：C++ OMAP3_MUX函数的具体用法？C++ OMAP3_MUX怎么用？C++ OMAP3_MUX使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。


在下文中一共展示了OMAP3_MUX函数的15个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于系统推荐出更棒的C++代码示例。

示例1: OMAP3_MUX

	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,

	.phy_reset  = true,
	/* PHY reset GPIO will be runtime programmed based on EVM version */
	.reset_gpio_port[0]  = -EINVAL,
	.reset_gpio_port[1]  = -EINVAL,
	.reset_gpio_port[2]  = -EINVAL
};

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
				OMAP_PIN_OFF_WAKEUPENABLE),
	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW),
	{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
#define board_mux	NULL
#endif

static struct omap_musb_board_data musb_board_data = {
	.interface_type		= MUSB_INTERFACE_ULPI,
	.mode			= MUSB_OTG,
	.power			= 100,
};
开发者ID:AdiPat，项目名称:i9003_Kernel，代码行数:29，代码来源:board-omap3evm.c

示例2: cm_t3517_init_nand

	.cs			= 0,
};

static void __init cm_t3517_init_nand(void)
{
	if (gpmc_nand_init(&cm_t3517_nand_data) < 0)
		pr_err("CM-T3517: NAND initialization failed\n");
}
#else
static inline void cm_t3517_init_nand(void) {}
#endif

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
	/* GPIO186 - Green LED */
	OMAP3_MUX(SYS_CLKOUT2, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),

	/* RTC GPIOs: */
	/* IO - GPIO153 */
	OMAP3_MUX(MCBSP4_DR, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
	/* WR# - GPIO154 */
	OMAP3_MUX(MCBSP4_DX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
	/* RD# - GPIO53 */
	OMAP3_MUX(GPMC_NCS2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
	/* CS# - GPIO163 */
	OMAP3_MUX(UART3_CTS_RCTX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
	/* CS EN - GPIO160 */
	OMAP3_MUX(MCBSP_CLKS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),

	/* HSUSB1 RESET */
	OMAP3_MUX(UART2_TX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
开发者ID:AceKatz，项目名称:networking_research，代码行数:31，代码来源:board-cm-t3517.c

示例3: ARRAY_SIZE

static struct matrix_keymap_data board_map_data = {
	.keymap			= board_keymap,
	.keymap_size		= ARRAY_SIZE(board_keymap),
};

static struct twl4030_keypad_data rx51_kp_data = {
	.keymap_data	= &board_map_data,
	.rows		= 8,
	.cols		= 8,
	.rep		= 1,
};

/* Enable input logic and pull all lines up when eMMC is on. */
static struct omap_board_mux rx51_mmc2_on_mux[] = {
	OMAP3_MUX(SDMMC2_CMD, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
	OMAP3_MUX(SDMMC2_DAT0, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
	OMAP3_MUX(SDMMC2_DAT1, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
	OMAP3_MUX(SDMMC2_DAT2, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
	OMAP3_MUX(SDMMC2_DAT3, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
	OMAP3_MUX(SDMMC2_DAT4, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
	OMAP3_MUX(SDMMC2_DAT5, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
	OMAP3_MUX(SDMMC2_DAT6, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
	OMAP3_MUX(SDMMC2_DAT7, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
	{ .reg_offset = OMAP_MUX_TERMINATOR },
};

/* Disable input logic and pull all lines down when eMMC is off. */
static struct omap_board_mux rx51_mmc2_off_mux[] = {
	OMAP3_MUX(SDMMC2_CMD, OMAP_PULL_ENA | OMAP_MUX_MODE0),
	OMAP3_MUX(SDMMC2_DAT0, OMAP_PULL_ENA | OMAP_MUX_MODE0),
开发者ID:020gzh，项目名称:linux，代码行数:30，代码来源:board-rx51-peripherals.c

示例4: OMAP3_MUX

static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {

	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
	.port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
	.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,

	.phy_reset  = true,
	.reset_gpio_port[0]  = -EINVAL,
	.reset_gpio_port[1]  = -EINVAL,
	.reset_gpio_port[2]  = -EINVAL
};

static struct omap_board_mux board_mux[] __initdata = {
	/* nCS and IRQ for Devkit8000 ethernet */
	OMAP3_MUX(GPMC_NCS6, OMAP_MUX_MODE0),
	OMAP3_MUX(ETK_D11, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),

	/* McSPI 2*/
	OMAP3_MUX(MCSPI2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(MCSPI2_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(MCSPI2_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(MCSPI2_CS0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(MCSPI2_CS1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),

	/* PENDOWN GPIO */
	OMAP3_MUX(ETK_D13, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),

	/* mUSB */
	OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
开发者ID:explodingboy70，项目名称:android_kernel_samsung_aries，代码行数:30，代码来源:board-devkit8000.c

示例5: cm_t35_init_i2c

	.vio		= &cm_t35_vio,
};

static void __init cm_t35_init_i2c(void)
{
	omap3_pmic_get_config(&cm_t35_twldata, TWL_COMMON_PDATA_USB,
			      TWL_COMMON_REGULATOR_VDAC |
			      TWL_COMMON_PDATA_AUDIO);

	omap3_pmic_init("tps65930", &cm_t35_twldata);
}

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
	/* nCS and IRQ for CM-T35 ethernet */
	OMAP3_MUX(GPMC_NCS5, OMAP_MUX_MODE0),
	OMAP3_MUX(UART3_CTS_RCTX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),

	/* nCS and IRQ for SB-T35 ethernet */
	OMAP3_MUX(GPMC_NCS4, OMAP_MUX_MODE0),
	OMAP3_MUX(GPMC_WAIT3, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),

	/* PENDOWN GPIO */
	OMAP3_MUX(GPMC_NCS6, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),

	/* mUSB */
	OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
开发者ID:0xroot，项目名称:Blackphone-BP1-Kernel，代码行数:31，代码来源:board-cm-t35.c

示例6: OMAP3_MUX

	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,

	.phy_reset  = true,
	/* PHY reset GPIO will be runtime programmed based on EVM version */
	.reset_gpio_port[0]  = -EINVAL,
	.reset_gpio_port[1]  = -EINVAL,
	.reset_gpio_port[2]  = -EINVAL
};

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux omap35x_board_mux[] __initdata = {
	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
				OMAP_PIN_OFF_WAKEUPENABLE),
	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
				OMAP_PIN_OFF_WAKEUPENABLE),
	OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_NONE),
	OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_NONE),
#ifdef CONFIG_WL12XX_PLATFORM_DATA
	/* WLAN IRQ - GPIO 149 */
	OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),

	/* WLAN POWER ENABLE - GPIO 150 */
	OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
开发者ID:PivotalBigData，项目名称:PivotalHD，代码行数:29，代码来源:board-omap3evm.c

示例7: OMAP3_MUX

static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
	.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,

	.phy_reset  = true,
	.reset_gpio_port[0]  = 57,
	.reset_gpio_port[1]  = -EINVAL,
	.reset_gpio_port[2]  = -EINVAL
};

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
	/* USB OTG DRVVBUS offset = 0x212 */
	OMAP3_MUX(CHASSIS_DMAREQ3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
	{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
#define board_mux	NULL
#endif

static void __init am3517_evm_init(void)
{
	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
	platform_add_devices(am3517_evm_devices,
				ARRAY_SIZE(am3517_evm_devices));

	omap_serial_init();
	usb_musb_init();
	usb_ehci_init(&ehci_pdata);
开发者ID:1plus4，项目名称:ev3sources，代码行数:30，代码来源:board-am3517evm.c

示例8: OMAP3_MUX

unsigned int wakeup_gpio[] = {
	OMAP_GPIO_KEY_PWRON,
	OMAP_GPIO_KEY_HOME,
};

#ifdef CONFIG_MACH_SAMSUNG_LATONA
static struct omap_board_mux board_mux[] __initdata = { // WLAN, Alex

/*
 *		Name, reg-offset,
 *		mux-mode | [active-mode | off-mode]
 */

	// 0 
	OMAP3_MUX(SDRC_D0,	OMAP_PIN_INPUT),
	// 1 
	OMAP3_MUX(SDRC_D1,	OMAP_PIN_INPUT),
	// 2 
	OMAP3_MUX(SDRC_D2,	OMAP_PIN_INPUT),
	// 3 
	OMAP3_MUX(SDRC_D3,	OMAP_PIN_INPUT),
	// 4 
	OMAP3_MUX(SDRC_D4,	OMAP_PIN_INPUT),
	// 5 
	OMAP3_MUX(SDRC_D5,	OMAP_PIN_INPUT),
	// 6 
	OMAP3_MUX(SDRC_D6,	OMAP_PIN_INPUT),
	// 7 
	OMAP3_MUX(SDRC_D7,	OMAP_PIN_INPUT),
	// 8
开发者ID:H1User，项目名称:i8320kernel，代码行数:30，代码来源:mux_latona_rev_r08.c

示例9: OMAP3_MUX

	{
		.name		= "Kernel-NAND",
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x280000 */
		.size		= 40 * (64 * 2048),
	},
	{
		.name		= "File System - NAND",
		.size		= MTDPART_SIZ_FULL,
		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x780000 */
	},
};

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux omap35x_board_mux[] __initdata = {
	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
				OMAP_PIN_OFF_WAKEUPENABLE),
	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
				OMAP_PIN_OFF_WAKEUPENABLE),
	OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_NONE),
	OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_NONE),
	OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_NONE),
	{ .reg_offset = OMAP_MUX_TERMINATOR },
};

static struct omap_board_mux omap36x_board_mux[] __initdata = {
	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
开发者ID:KalenAnson，项目名称:NestDFUAttack，代码行数:31，代码来源:board-omap3evm.c

示例10: omap_mux_init_signal

		/* OMAP3 Torpedo board */
		board_smsc911x_data.gpio_irq = OMAP3_TORPEDO_SMSC911X_GPIO_IRQ;
		omap_mux_init_signal("gpio_129", OMAP_PIN_INPUT);
	} else {
		/* unsupported board */
		printk(KERN_ERR "%s(): unknown machine type\n", __func__);
		return;
	}

	gpmc_smsc911x_init(&board_smsc911x_data);
}

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
	/* mUSB */
	OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
	OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),

	{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif
开发者ID:4atty，项目名称:linux，代码行数:31，代码来源:board-omap3logic.c

示例11: OMAP3_MUX

		.vcc_gpio = -EINVAL,
	},
};

static struct usbhs_omap_platform_data igep2_usbhs_bdata __initdata = {
	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
};

static struct usbhs_omap_platform_data igep3_usbhs_bdata __initdata = {
	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
};

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
	/* Display Sub System */
	OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
	OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
开发者ID:1youhun1，项目名称:linux，代码行数:31，代码来源:board-igep0020.c

示例12: OMAP3_MUX

	.port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
#else
	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
#endif
	.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,

	.phy_reset  = true,
	.reset_gpio_port[0]  = 57,
	.reset_gpio_port[1]  = -EINVAL,
	.reset_gpio_port[2]  = -EINVAL
};

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
	/* USB OTG DRVVBUS offset = 0x212 */
	OMAP3_MUX(SAD2D_MCAD23, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
	OMAP3_MUX(MCBSP_CLKS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
	OMAP3_MUX(GPMC_NCS4, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLDOWN),
	{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif


static struct resource am3517_hecc_resources[] = {
	{
		.start	= AM35XX_IPSS_HECC_BASE,
		.end	= AM35XX_IPSS_HECC_BASE + 0x3FFF,
		.flags	= IORESOURCE_MEM,
	},
	{
		.start	= INT_35XX_HECC0_IRQ,
开发者ID:sytuxww，项目名称:android2.3-dm8168，代码行数:31，代码来源:board-am3517evm.c

示例13: OMAP3_MUX

	/* PHY reset GPIO will be runtime programmed based on EVM version */
	.reset_gpio_port[0]  = -EINVAL,
	.reset_gpio_port[1]  = -EINVAL,
	.reset_gpio_port[2]  = -EINVAL,

	.aux[0]	= 0,
	.aux[1]	= 0,
	.aux[2]	= 0,
};

/* CUS Pkg. */
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
#ifdef CONFIG_KEYBOARD_TWL4030
	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
				OMAP_PIN_OFF_WAKEUPENABLE),
#endif
#ifdef CONFIG_TOUCHSCREEN_ADS7846
	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
				OMAP_PIN_OFF_WAKEUPENABLE),
	OMAP3_MUX(MCSPI1_CS3, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),                 /* GPIO177, default touchscreen pendown */
#endif
	OMAP3_MUX(ETK_D10, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),			/* GPIO24, USB */
	OMAP3_MUX(ETK_D12, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),			/* GPIO26, voltage buffer disable */
	OMAP3_MUX(ETK_D14, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),			/* GPIO28, LCD backlight */
	OMAP3_MUX(ETK_D15, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),			/* GPIO29, ETH0 */
	OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),		/* GPIO131, LCD ENVDD */
#ifdef CONFIG_TOUCHSCREEN_CTW6120
	OMAP3_MUX(CAM_D8, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),                     /* GPIO105, CTP touchscreen data ready */
开发者ID:psanchez，项目名称:ipspeaker-om3x，代码行数:31，代码来源:board-var-som-om3x.c

示例14: OMAP3_MUX

static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {

	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
	.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,

	.phy_reset  = true,
	.reset_gpio_port[0]  = -EINVAL,
	.reset_gpio_port[1]  = 147,
	.reset_gpio_port[2]  = -EINVAL
};

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
	OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),	//W-Y-L GPIO 133
	OMAP3_MUX(SDMMC2_DAT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLDOWN),	//W-Y-L GPIO 137
	{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
#define board_mux	NULL
#endif

static int __init expansionboard_setup(char *str)
{
	if (!str)
		return -EINVAL;
	strncpy(expansionboard_name, str, 16);
	printk(KERN_INFO "Beagle expansionboard: %s\n", expansionboard_name);
	return 0;
}
开发者ID:andydev，项目名称:spec_mtk，代码行数:30，代码来源:board-omap3beagle.c

示例15: OMAP3_MUX

 *    Copyright (c) 2010-2011 Nest, Inc.
 *
 *      Author: Grant Erickson <[email protected]>
 *
 *    This program is free software; you can redistribute it and/or
 *    modify it under the terms of the GNU General Public License
 *    version 2 as published by the Free Software Foundation.
 *
 *    Description:
 *      This file implements the pin multiplexer settings for the Nest
 *      Diamond prototype boards.
 *
 */

static struct omap_board_mux diamond_prototype_mux[] __initdata = {
	OMAP3_MUX(SYS_NIRQ,			OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP   | OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),

	// SDRC
	OMAP3_MUX(SDRC_A13,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
	OMAP3_MUX(SDRC_A14,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
	OMAP3_MUX(SDRC_D31,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
	OMAP3_MUX(SDRC_D31,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
	OMAP3_MUX(SDRC_D30,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
	OMAP3_MUX(SDRC_D29,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
	OMAP3_MUX(SDRC_D28,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
	OMAP3_MUX(SDRC_D27,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
	OMAP3_MUX(SDRC_D26,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
	OMAP3_MUX(SDRC_D25,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
	OMAP3_MUX(SDRC_D24,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
	OMAP3_MUX(SDRC_D23,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
	OMAP3_MUX(SDRC_D22,			OMAP_MUX_MODE7 | OMAP_PIN_INPUT_PULLDOWN | OMAP_PIN_OFF_INPUT_PULLDOWN ), // Unused
开发者ID:KalenAnson，项目名称:NestDFUAttack，代码行数:31，代码来源:board-diamond-prototype-mux.c


注：本文中的OMAP3_MUX函数示例由纯净天空整理自Github/MSDocs等开源代码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。