C++ IS_PWR_REGULATOR函数代码示例

/*******************************************************************************
* 函数名称: PWR_EnterSTOPMode
* 功能描述: 进入STOP模式.
* 输入参数: PWR_Regulator:STOP模式的校准状态。
*                    这个参数可以是下面的值之一:
*                       - PWR_Regulator_ON: 校准器开启的STOP模式
*                       - PWR_Regulator_LowPower: 在低功耗模式下带有校准器的STOP模式。
*                  - PWR_STOPEntry: 这个参数定义了STOP进入模式.
*                    这个参数可以是下面的值之一:
*                       - PWR_STOPEntry_WFI: 进入有WFI指令的STOP模式
*                       - PWR_STOPEntry_WFE: 进入有WFE指令的STOP模式
* 输出参数: 无
* 返回参数: 无
*******************************************************************************/
void PWR_EnterSTOPMode(u32 PWR_Regulator, u8 PWR_STOPEntry)
{
  u32 tmpreg = 0;

  /* Check the parameters [检查参数]*/
  assert_param(IS_PWR_REGULATOR(PWR_Regulator));
  assert_param(IS_PWR_STOP_ENTRY(PWR_STOPEntry));
  
  /* Select the regulator state in STOP mode [在停止模式选择校准状态]*/
  tmpreg = PWR->CR;

  /* Clear PDDS and LPDS bits [清PDDS和LPDS位]*/
  tmpreg &= CR_DS_Mask;

  /* Set LPDS bit according to PWR_Regulator value [依照PWR_Regulator值置位LPDS]*/
  tmpreg |= PWR_Regulator;

  /* Store the new value [保存新的值]*/
  PWR->CR = tmpreg;

  /* Set SLEEPDEEP bit of Cortex System Control Register [置位Cortex系统的控制寄存器SLEEPDEEP位]*/
  *(vu32 *) SCB_SysCtrl |= SysCtrl_SLEEPDEEP_Set;
  
  /* Select STOP mode entry [选择停止模式进入]*/
  if(PWR_STOPEntry == PWR_STOPEntry_WFI)
  {   
    /* Request Wait For Interrupt [请求等待中断]*/
    __WFI();
  }
  else
  {
    /* Request Wait For Event [请求等待事件]*/
    __WFE();
  }
}

/**
  * @brief Enters Sleep mode.
  * @note In Sleep mode, all I/O pins keep the same state as in Run mode.
  * @param Regulator: Specifies the regulator state in SLEEP mode.
  *          This parameter can be one of the following values:
  *            @arg PWR_MAINREGULATOR_ON: SLEEP mode with regulator ON
  *            @arg PWR_LOWPOWERREGULATOR_ON: SLEEP mode with low power regulator ON
  * @param SLEEPEntry: Specifies if SLEEP mode is entered with WFI or WFE instruction.
  *           When WFI entry is used, tick interrupt have to be disabled if not desired as 
  *           the interrupt wake up source.
  *           This parameter can be one of the following values:
  *            @arg PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction
  *            @arg PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction
  * @retval None
  */
void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry)
{
   uint32_t tmpreg = 0;
  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(Regulator));
  assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry));

   /* Select the regulator state in Sleep mode ---------------------------------*/
  tmpreg = PWR->CR;
  /* Clear PDDS and LPDS bits */
  tmpreg &= (uint32_t)~(PWR_CR_PDDS | PWR_CR_LPSDSR);

 /* Set LPSDSR bit according to PWR_Regulator value */
  tmpreg |= Regulator;

  /* Store the new value */
  PWR->CR = tmpreg;
  
  /* Clear SLEEPDEEP bit of Cortex System Control Register */
  SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk);

  /* Select SLEEP mode entry -------------------------------------------------*/
  if(SLEEPEntry == PWR_SLEEPENTRY_WFI)
  {
    /* Request Wait For Interrupt */
    __WFI();
  }
  else
  {
    /* Request Wait For Event */
    __SEV();
    __WFE();
    __WFE();
  }
}

/**
  * @brief Enters Sleep mode.
  *
  * @note In Sleep mode, all I/O pins keep the same state as in Run mode.
  *
  * @note In Sleep mode, the systick is stopped to avoid exit from this mode with
  *       systick interrupt when used as time base for Timeout
  *
  * @param Regulator Specifies the regulator state in SLEEP mode.
  *            This parameter can be one of the following values:
  *            @arg PWR_MAINREGULATOR_ON: SLEEP mode with regulator ON
  *            @arg PWR_LOWPOWERREGULATOR_ON: SLEEP mode with low power regulator ON
  * @note This parameter is not used for the STM32F7 family and is kept as parameter
  *       just to maintain compatibility with the lower power families.
  * @param SLEEPEntry Specifies if SLEEP mode in entered with WFI or WFE instruction.
  *          This parameter can be one of the following values:
  *            @arg PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction
  *            @arg PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction
  * @retval None
  */
void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry)
{
  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(Regulator));
  assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry));

  /* Clear SLEEPDEEP bit of Cortex System Control Register */
  CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk));

  /* Ensure that all instructions done before entering SLEEP mode */
  __DSB();
  __ISB();

  /* Select SLEEP mode entry -------------------------------------------------*/
  if(SLEEPEntry == PWR_SLEEPENTRY_WFI)
  {
    /* Request Wait For Interrupt */
    __WFI();
  }
  else
  {
    /* Request Wait For Event */
    __SEV();
    __WFE();
    __WFE();
  }
}

/**
  * @brief Enters Stop mode. 
  * @note  In Stop mode, all I/O pins keep the same state as in Run mode.
  * @note  When exiting Stop mode by using an interrupt or a wakeup event,
  *        HSI RC oscillator is selected as system clock.
  * @note  When the voltage regulator operates in low power mode, an additional
  *         startup delay is incurred when waking up from Stop mode. 
  *         By keeping the internal regulator ON during Stop mode, the consumption
  *         is higher although the startup time is reduced.    
  * @param Regulator: Specifies the regulator state in Stop mode.
  *          This parameter can be one of the following values:
  *            @arg PWR_MAINREGULATOR_ON: Stop mode with regulator ON
  *            @arg PWR_LOWPOWERREGULATOR_ON: Stop mode with low power regulator ON
  * @param STOPEntry: Specifies if Stop mode in entered with WFI or WFE instruction.
  *          This parameter can be one of the following values:
  *            @arg PWR_STOPENTRY_WFI: Enter Stop mode with WFI instruction
  *            @arg PWR_STOPENTRY_WFE: Enter Stop mode with WFE instruction   
  * @retval None
  */
void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry)
{
  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(Regulator));
  assert_param(IS_PWR_STOP_ENTRY(STOPEntry));

  /* Clear PDDS bit in PWR register to specify entering in STOP mode when CPU enter in Deepsleep */ 
  CLEAR_BIT(PWR->CR,  PWR_CR_PDDS);

  /* Select the voltage regulator mode by setting LPDS bit in PWR register according to Regulator parameter value */
  MODIFY_REG(PWR->CR, PWR_CR_LPDS, Regulator);

  /* Set SLEEPDEEP bit of Cortex System Control Register */
  SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk));

  /* Select Stop mode entry --------------------------------------------------*/
  if(STOPEntry == PWR_STOPENTRY_WFI)
  {
    /* Request Wait For Interrupt */
    __WFI();
  }
  else
  {
    /* Request Wait For Event */
    __SEV();
    PWR_OverloadWfe(); /* WFE redefine locally */
    PWR_OverloadWfe(); /* WFE redefine locally */
  }
  /* Reset SLEEPDEEP bit of Cortex System Control Register */
  CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk));
}

/**
  * @brief  Enters STOP mode.
  * @param  PWR_Regulator: specifies the regulator state in STOP mode.
  *   This parameter can be one of the following values:
  *     @arg PWR_Regulator_ON: STOP mode with regulator ON
  *     @arg PWR_Regulator_LowPower: STOP mode with regulator in low power mode
  * @param  PWR_STOPEntry: specifies if STOP mode in entered with WFI or WFE instruction.
  *   This parameter can be one of the following values:
  *     @arg PWR_STOPEntry_WFI: enter STOP mode with WFI instruction
  *     @arg PWR_STOPEntry_WFE: enter STOP mode with WFE instruction
  * @retval None
  */
void PWR_EnterSTOPMode(uint32_t PWR_Regulator, uint8_t PWR_STOPEntry)
{
  uint32_t tmpreg = 0;
  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(PWR_Regulator));
  assert_param(IS_PWR_STOP_ENTRY(PWR_STOPEntry));
  
  /* Select the regulator state in STOP mode ---------------------------------*/
  tmpreg = PWR->CR;
  /* Clear PDDS and LPDS bits */
  tmpreg &= CR_DS_Mask;
  /* Set LPDS bit according to PWR_Regulator value */
  tmpreg |= PWR_Regulator;
  /* Store the new value */
  PWR->CR = tmpreg;
  /* Set SLEEPDEEP bit of Cortex System Control Register */
  *(__IO uint32_t *) SCB_SysCtrl |= SysCtrl_SLEEPDEEP_Set;
  
  /* Select STOP mode entry --------------------------------------------------*/
  if(PWR_STOPEntry == PWR_STOPEntry_WFI)
  {   
    /* Request Wait For Interrupt */
    __WFI();
  }
  else
  {
    /* Request Wait For Event */
    __WFE();
  }
}

/**
  * @brief Enters Stop mode. 
  * @note  In Stop mode, all I/O pins keep the same state as in Run mode.
  * @note  When exiting Stop mode by using an interrupt or a wakeup event,
  *        MSI RC oscillator is selected as system clock.
  * @note  When the voltage regulator operates in low power mode, an additional
  *         startup delay is incurred when waking up from Stop mode. 
  *         By keeping the internal regulator ON during Stop mode, the consumption
  *         is higher although the startup time is reduced.    
  * @param Regulator: Specifies the regulator state in Stop mode.
  *          This parameter can be one of the following values:
  *            @arg PWR_MAINREGULATOR_ON: Stop mode with regulator ON
  *            @arg PWR_LOWPOWERREGULATOR_ON: Stop mode with low power regulator ON
  * @param STOPEntry: Specifies if Stop mode in entered with WFI or WFE instruction.
  *          This parameter can be one of the following values:
  *            @arg PWR_STOPENTRY_WFI: Enter Stop mode with WFI instruction
  *            @arg PWR_STOPENTRY_WFE: Enter Stop mode with WFE instruction   
  * @retval None
  */
void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry)
{
  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(Regulator));
  assert_param(IS_PWR_STOP_ENTRY(STOPEntry));

  /* Select the regulator state in Stop mode: Set PDDS and LPSDSR bit according to PWR_Regulator value */
  MODIFY_REG(PWR->CR, (PWR_CR_PDDS | PWR_CR_LPSDSR), Regulator);

  /* Set SLEEPDEEP bit of Cortex System Control Register */
  SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk));

  /* Select Stop mode entry --------------------------------------------------*/
  if(STOPEntry == PWR_STOPENTRY_WFI)
  {
    /* Request Wait For Interrupt */
    __WFI();
  }
  else
  {
    /* Request Wait For Event */
    __SEV();
    __WFE();
    __WFE();
  }
  /* Reset SLEEPDEEP bit of Cortex System Control Register */
  CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk));
}

/**
  * @brief  Enter the system to STOP mode.
  * @note   In System Stop mode, all I/O pins keep the same state as in Run mode.
  * @note   When exiting System Stop mode by issuing an interrupt or a wakeup event,
  *         the HSI RC oscillator is selected as default system wakeup clock.
  * @note   In System STOP mode, when the voltage regulator operates in low power mode,
  *         an additional startup delay is incurred when the system is waking up.
  *         By keeping the internal regulator ON during Stop mode, the consumption
  *         is higher although the startup time is reduced.
  * @param  Regulator: Specifies the regulator state in Stop mode.
  *          This parameter can be one of the following values:
  *            @arg PWR_MAINREGULATOR_ON: Stop mode with regulator ON
  *            @arg PWR_LOWPOWERREGULATOR_ON: Stop mode with low power regulator ON
  * @param  STOPEntry: Specifies if Stop mode in entered with WFI or WFE instruction.
  *          This parameter can be one of the following values:
  *            @arg PWR_STOPENTRY_WFI: Enter Stop mode with WFI instruction
  *            @arg PWR_STOPENTRY_WFE: Enter Stop mode with WFE instruction
  * @retval None
  */
void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry)
{
  uint32_t tmpreg = 0;

  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(Regulator));
  assert_param(IS_PWR_STOP_ENTRY(STOPEntry));

  /* Select the regulator state in Stop mode */
  tmpreg = PWR->CR1;
  /* Clear PDDS and LPDS bits */
  tmpreg &= (uint32_t)~(PWR_CR1_LPDS);

  /* Set LPDS bit according to Regulator value */
  tmpreg |= Regulator;

  /* Store the new value */
  PWR->CR1 = tmpreg;

  /* Keep DSTOP mode when D1 domain enters Deepsleep */
  CLEAR_BIT(PWR->CPUCR, PWR_CPUCR_PDDS_D1);

  /* Keep DSTOP mode when D2 domain enters Deepsleep */
  CLEAR_BIT(PWR->CPUCR, PWR_CPUCR_PDDS_D2);

  /* Keep DSTOP mode when D3 domain enters Deepsleep */
  CLEAR_BIT(PWR->CPUCR, PWR_CPUCR_PDDS_D3);

  /* Set SLEEPDEEP bit of Cortex System Control Register */
  SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk;

  /* Ensure that all instructions done before entering STOP mode */
  __DSB();
  __ISB();

  /* Select Stop mode entry */
  if(STOPEntry == PWR_STOPENTRY_WFI)
  {
    /* Request Wait For Interrupt */
    __WFI();
  }
  else
  {
    /* Request Wait For Event */
    __SEV();
    __WFE();
    __WFE();
  }
  /* Reset SLEEPDEEP bit of Cortex System Control Register */
  SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk);
}

/**
  * @brief Enter Stop mode
  * @note  This API is named HAL_PWR_EnterSTOPMode to ensure compatibility with legacy code running
  *        on devices where only "Stop mode" is mentioned with main or low power regulator ON.
  * @note  In Stop mode, all I/O pins keep the same state as in Run mode.          
  * @note  All clocks in the VCORE domain are stopped; the PLL, the MSI, 
  *        the HSI and the HSE oscillators are disabled. Some peripherals with the wakeup capability 
  *        (I2Cx, USARTx and LPUART) can switch on the HSI to receive a frame, and switch off the HSI 
  *        after receiving the frame if it is not a wakeup frame. In this case, the HSI clock is propagated 
  *        only to the peripheral requesting it.
  *        SRAM1, SRAM2 and register contents are preserved.
  *        The BOR is available.
  *        The voltage regulator can be configured either in normal (Stop 0) or low-power mode (Stop 1).  
  * @note  When exiting Stop 0 or Stop 1 mode by issuing an interrupt or a wakeup event,
  *         the HSI RC oscillator is selected as system clock if STOPWUCK bit in RCC_CFGR register
  *         is set; the MSI oscillator is selected if STOPWUCK is cleared.  
  * @note  When the voltage regulator operates in low power mode (Stop 1), an additional
  *         startup delay is incurred when waking up.
  *         By keeping the internal regulator ON during Stop mode (Stop 0), the consumption
  *         is higher although the startup time is reduced.
  * @param Regulator: Specifies the regulator state in Stop mode.
  *          This parameter can be one of the following values:
  *            @arg @ref PWR_MAINREGULATOR_ON  Stop 0 mode (main regulator ON)
  *            @arg @ref PWR_LOWPOWERREGULATOR_ON  Stop 1 mode (low power regulator ON) 
  * @param STOPEntry: Specifies Stop 0 or Stop 1 mode is entered with WFI or WFE instruction.
  *          This parameter can be one of the following values:
  *            @arg @ref PWR_STOPENTRY_WFI  Enter Stop 0 or Stop 1 mode with WFI instruction.
  *            @arg @ref PWR_STOPENTRY_WFE  Enter Stop 0 or Stop 1 mode with WFE instruction.
  * @retval None
  */
void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry)
{
  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(Regulator));
  
  if(Regulator == PWR_LOWPOWERREGULATOR_ON)
  {
    HAL_PWREx_EnterSTOP1Mode(STOPEntry);
  }
  else
  {
    HAL_PWREx_EnterSTOP0Mode(STOPEntry);
  }
}

/**
  * @brief  Enters STOP mode.
  * @param  PWR_Regulator: specifies the regulator state in STOP mode.
  *   This parameter can be one of the following values:
  *     @arg PWR_Regulator_ON: STOP mode with regulator ON
  *     @arg PWR_Regulator_LowPower: STOP mode with regulator in low power mode
  * @param  PWR_STOPEntry: specifies if STOP mode in entered with WFI or WFE instruction.
  *   This parameter can be one of the following values:
  *     @arg PWR_STOPEntry_WFI: enter STOP mode with WFI instruction
  *     @arg PWR_STOPEntry_WFE: enter STOP mode with WFE instruction
  * @retval None
  */
void PWR_EnterSTOPMode(uint32_t PWR_Regulator, uint8_t PWR_STOPEntry)
{
	
#ifdef	OS_UCOS
	OS_CPU_SR  cpu_sr;
#endif
	

  uint32_t tmpreg = 0;
	
#ifdef	OS_UCOS
	OS_ENTER_CRITICAL();
#endif
	 
  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(PWR_Regulator));
  assert_param(IS_PWR_STOP_ENTRY(PWR_STOPEntry));
  
  /* Select the regulator state in STOP mode ---------------------------------*/
  tmpreg = PWR->CR;
  /* Clear PDDS and LPDS bits */
  tmpreg &= CR_DS_MASK;
  /* Set LPDS bit according to PWR_Regulator value */
  tmpreg |= PWR_Regulator;
  /* Store the new value */
  PWR->CR = tmpreg;
  /* Set SLEEPDEEP bit of Cortex System Control Register */
  SCB->SCR |= SCB_SCR_SLEEPDEEP;
  
  /* Select STOP mode entry --------------------------------------------------*/
  if(PWR_STOPEntry == PWR_STOPEntry_WFI)
  {   
    /* Request Wait For Interrupt */
    __WFI();
  }
  else
  {
    /* Request Wait For Event */
    __WFE();
  }
  
  /* Reset SLEEPDEEP bit of Cortex System Control Register */
  SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP);  
	
#ifdef	OS_UCOS
	OS_EXIT_CRITICAL();
#endif
	
}

/**
  * @brief Enter Sleep or Low-power Sleep mode.
  * @note  In Sleep/Low-power Sleep mode, all I/O pins keep the same state as in Run mode.
  * @param Regulator: Specifies the regulator state in Sleep/Low-power Sleep mode.
  *          This parameter can be one of the following values:
  *            @arg @ref PWR_MAINREGULATOR_ON Sleep mode (regulator in main mode)
  *            @arg @ref PWR_LOWPOWERREGULATOR_ON Low-power Sleep mode (regulator in low-power mode) 
  * @note  Low-power Sleep mode is entered from Low-power Run mode. Therefore, if not yet 
  *        in Low-power Run mode before calling HAL_PWR_EnterSLEEPMode() with Regulator set 
  *        to PWR_LOWPOWERREGULATOR_ON, the user can optionally configure the    
  *        Flash in power-down monde in setting the SLEEP_PD bit in FLASH_ACR register.
  *        Additionally, the clock frequency must be reduced below 2 MHz.
  *        Setting SLEEP_PD in FLASH_ACR then appropriately reducing the clock frequency must 
  *        be done before calling HAL_PWR_EnterSLEEPMode() API. 
  * @note  When exiting Low-power Sleep mode, the MCU is in Low-power Run mode. To move in 
  *        Run mode, the user must resort to HAL_PWREx_DisableLowPowerRunMode() API.       
  * @param SLEEPEntry: Specifies if Sleep mode is entered with WFI or WFE instruction.
  *           This parameter can be one of the following values:
  *            @arg @ref PWR_SLEEPENTRY_WFI enter Sleep or Low-power Sleep mode with WFI instruction
  *            @arg @ref PWR_SLEEPENTRY_WFE enter Sleep or Low-power Sleep mode with WFE instruction
  * @note  When WFI entry is used, tick interrupt have to be disabled if not desired as 
  *        the interrupt wake up source.   
  * @retval None
  */
void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry)
{
  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(Regulator));
  assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry));

  /* Set Regulator parameter */
  if (Regulator == PWR_MAINREGULATOR_ON)
  {
    /* If in low-power run mode at this point, exit it */
    if (HAL_IS_BIT_SET(PWR->SR2, PWR_SR2_REGLPF))
    {
      HAL_PWREx_DisableLowPowerRunMode();  
    } 
    /* Regulator now in main mode. */
  }
  else
  {
    /* If in run mode, first move to low-power run mode.
       The system clock frequency must be below 2 MHz at this point. */
    if (HAL_IS_BIT_SET(PWR->SR2, PWR_SR2_REGLPF) == RESET)
    {
      HAL_PWREx_EnableLowPowerRunMode();  
    } 
  } 
    
  /* Clear SLEEPDEEP bit of Cortex System Control Register */
  CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk));
  
  /* Select SLEEP mode entry -------------------------------------------------*/
  if(SLEEPEntry == PWR_SLEEPENTRY_WFI)
  {
    /* Request Wait For Interrupt */
    __WFI();
  }
  else
  {
    /* Request Wait For Event */
    __SEV();
    __WFE();
    __WFE();
  }

}

/**
  * @brief  Enters STOP mode.
  * @note   In Stop mode, all I/O pins keep the same state as in Run mode.
  * @note   When exiting Stop mode by issuing an interrupt or a wakeup event, 
  *         the HSI RC oscillator is selected as system clock.
  * @note   When the voltage regulator operates in low power mode, an additional 
  *         startup delay is incurred when waking up from Stop mode. 
  *         By keeping the internal regulator ON during Stop mode, the consumption 
  *         is higher although the startup time is reduced.
  * @param  PWR_Regulator: specifies the regulator state in STOP mode.
  *         This parameter can be one of the following values:
  *             @arg PWR_Regulator_ON: STOP mode with regulator ON
  *             @arg PWR_Regulator_LowPower: STOP mode with regulator in low power mode
  * @param  PWR_STOPEntry: specifies if STOP mode in entered with WFI or WFE instruction.
  *         This parameter can be one of the following values:
  *             @arg PWR_STOPEntry_WFI: enter STOP mode with WFI instruction
  *             @arg PWR_STOPEntry_WFE: enter STOP mode with WFE instruction
                @arg PWR_STOPEntry_SLEEPONEXIT: enter STOP mode with SLEEPONEXIT instruction
  * @retval None
  */
void PWR_EnterSTOPMode(uint32_t PWR_Regulator, uint8_t PWR_STOPEntry)
{
  uint32_t tmpreg = 0;
  
  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(PWR_Regulator));
  assert_param(IS_PWR_STOP_ENTRY(PWR_STOPEntry));
  
  /* Select the regulator state in STOP mode ---------------------------------*/
  tmpreg = PWR->CR;
  /* Clear PDDS and LPDSR bits */
  tmpreg &= CR_DS_MASK;
  
  /* Set LPDSR bit according to PWR_Regulator value */
  tmpreg |= PWR_Regulator;
  
  /* Store the new value */
  PWR->CR = tmpreg;
  
  /* Set SLEEPDEEP bit of Cortex-M0 System Control Register */
  SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk;
  
  /* Select STOP mode entry --------------------------------------------------*/
  if(PWR_STOPEntry == PWR_STOPEntry_WFI)
  {
    /* Request Wait For Interrupt */
    __WFI();
    /* Reset SLEEPDEEP bit of Cortex System Control Register */
    SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk); 
  }
  else if (PWR_STOPEntry == PWR_STOPEntry_WFE)
  {
    /* Request Wait For Event */
    __WFE();
    /* Reset SLEEPDEEP bit of Cortex System Control Register */
    SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk);   
  }
  else
  {
    /* Set SLEEP on exit bit of Cortex-M0 System Control Register */
    SCB->SCR |= SCB_SCR_SLEEPONEXIT_Msk;
  }
}

/**
  * @brief Enters Sleep mode.
  *   
  * @note In Sleep mode, all I/O pins keep the same state as in Run mode.
  * 
  * @note In Sleep mode, the systick is stopped to avoid exit from this mode with
  *       systick interrupt when used as time base for Timeout 
  *                
  * @param Regulator: Specifies the regulator state in SLEEP mode.
  *            This parameter can be one of the following values:
  *            @arg PWR_MAINREGULATOR_ON: SLEEP mode with regulator ON
  *            @arg PWR_LOWPOWERREGULATOR_ON: SLEEP mode with low power regulator ON
  * @note This parameter is not used for the STM32F4 family and is kept as parameter
  *       just to maintain compatibility with the lower power families.
  * @param SLEEPEntry: Specifies if SLEEP mode in entered with WFI or WFE instruction.
  *          This parameter can be one of the following values:
  *            @arg PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction
  *            @arg PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction
  * @retval None
  */
void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry)
{
  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(Regulator));
  assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry));

  /* Select SLEEP mode entry -------------------------------------------------*/
  if(SLEEPEntry == PWR_SLEEPENTRY_WFI)
  {   
    /* Request Wait For Interrupt */
    __WFI();
  }
  else
  {
    /* Request Wait For Event */
    __SEV();
    __WFE();
    __WFE();
  }
}

/**
  * @brief Enters Sleep mode.
  * @note  In Sleep mode, all I/O pins keep the same state as in Run mode.
  * @param Regulator: Specifies the regulator state in SLEEP mode.
  *           On STM32F0 devices, this parameter is a dummy value and it is ignored
  *           as regulator can't be modified in this mode. Parameter is kept for platform
  *           compatibility.
  * @param SLEEPEntry: Specifies if SLEEP mode is entered with WFI or WFE instruction.
  *           When WFI entry is used, tick interrupt have to be disabled if not desired as 
  *           the interrupt wake up source.
  *           This parameter can be one of the following values:
  *            @arg PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction
  *            @arg PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction
  * @retval None
  */
void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry)
{
  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(Regulator));
  assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry));

  /* Clear SLEEPDEEP bit of Cortex System Control Register */
  SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk);

  /* Select SLEEP mode entry -------------------------------------------------*/
  if(SLEEPEntry == PWR_SLEEPENTRY_WFI)
  {
    /* Request Wait For Interrupt */
    __WFI();
  }
  else
  {
    /* Request Wait For Event */
    __SEV();
    __WFE();
    __WFE();
  }
}

/**
  * @brief Enters Sleep mode.
  *   
  * @note In Sleep mode, all I/O pins keep the same state as in Run mode.
  * 
  * @note In Sleep mode, the systick is stopped to avoid exit from this mode with
  *       systick interrupt when used as time base for Timeout 
  *                
  * @param Regulator: Specifies the regulator state in SLEEP mode.
  *            This parameter can be one of the following values:
  *            @arg PWR_MAINREGULATOR_ON: SLEEP mode with regulator ON
  *            @arg PWR_LOWPOWERREGULATOR_ON: SLEEP mode with low power regulator ON
  * @note This parameter is not used for the STM32F2 family and is kept as parameter
  *       just to maintain compatibility with the lower power families.
  * @param SLEEPEntry: Specifies if SLEEP mode in entered with WFI or WFE instruction.
  *          This parameter can be one of the following values:
  *            @arg PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction
  *            @arg PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction
  * @retval None
  */
void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry)
{
  /* Check the parameters */
  assert_param(IS_PWR_REGULATOR(Regulator));
  assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry));
  
  /* Disable SysTick Timer */
  SysTick->CTRL  &= 0xFE;
  
  /* Select SLEEP mode entry -------------------------------------------------*/
  if(SLEEPEntry == PWR_SLEEPENTRY_WFI)
  {   
    /* Request Wait For Interrupt */
    __WFI();
  }
  else
  {
    /* Request Wait For Event */
    __WFE();
  }

  /* Enable SysTick Timer */
  SysTick->CTRL  |= 0x01;
}