C++ I2C_CheckEvent函数代码示例

/**
  * @brief  Checks the LM75 status.
  * @param  None
  * @retval ErrorStatus: LM75 Status (ERROR or SUCCESS).
  */
ErrorStatus LM75_GetStatus(void)
{
  uint32_t I2C_TimeOut = I2C_TIMEOUT;

  /*!< Clear the LM75_I2C AF flag */
  I2C_ClearFlag(LM75_I2C, I2C_FLAG_AF);

  /*!< Enable LM75_I2C acknowledgement if it is already disabled by other function */
  I2C_AcknowledgeConfig(LM75_I2C, ENABLE);

  /*---------------------------- Transmission Phase ---------------------------*/

  /*!< Send LM75_I2C START condition */
  I2C_GenerateSTART(LM75_I2C, ENABLE);

  /*!< Test on LM75_I2C EV5 and clear it */
  while ((!I2C_GetFlagStatus(LM75_I2C,I2C_FLAG_SB)) && I2C_TimeOut)  /*!< EV5 */
  {
    I2C_TimeOut--;
  }
  if (I2C_TimeOut == 0)
  {
    return ERROR;
  }
  
  I2C_TimeOut = I2C_TIMEOUT;

  /*!< Send STLM75 slave address for write */
  I2C_Send7bitAddress(LM75_I2C, LM75_ADDR, I2C_Direction_Transmitter);

  while ((!I2C_CheckEvent(LM75_I2C, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED)) && I2C_TimeOut)/* EV6 */
  {
    I2C_TimeOut--;
  }

  if ((I2C_GetFlagStatus(LM75_I2C, I2C_FLAG_AF) != 0x00) || (I2C_TimeOut == 0))
  {
    return ERROR;
  }
  else
  {
    return SUCCESS;
  }
}

int i2c_write(i2c_t *obj, int address, const char *data, int length, int stop) {
    I2C_TypeDef *i2c = (I2C_TypeDef *)(obj->i2c);
    int timeout;
    int count;
  
/*
    // Wait until the bus is not busy anymore
    timeout = LONG_TIMEOUT;
    while (I2C_GetFlagStatus(i2c, I2C_FLAG_BUSY) == SET) {
        timeout--;
        if (timeout == 0) {
            return 0;
        }
    }
*/

    i2c_start(obj);

    // Send slave address for write
    I2C_Send7bitAddress(i2c, address, I2C_Direction_Transmitter);
  
    // Wait address is acknowledged
    timeout = FLAG_TIMEOUT;
    while (I2C_CheckEvent(i2c, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED) == ERROR) {
        timeout--;
        if (timeout == 0) {
            return 0;
        }
    }

    for (count = 0; count < length; count++) {
        if (i2c_byte_write(obj, data[count]) != 1) {
            i2c_stop(obj);
            return 0;
        }
    }

    // If not repeated start, send stop.
    if (stop) {
        i2c_stop(obj);
    }

    return count;
}

Status I2C_Write(I2C_TypeDef* I2Cx, const uint8_t* buf,  uint32_t nbyte, uint8_t SlaveAddress)
{
    __IO uint32_t Timeout = 0;

    /* Enable Error IT (used in all modes: DMA, Polling and Interrupts */
    //    I2Cx->CR2 |= I2C_IT_ERR;

    if (nbyte)
      {
	Timed(I2C_GetFlagStatus(I2Cx, I2C_FLAG_BUSY));

	// Intiate Start Sequence

	I2C_GenerateSTART(I2Cx, ENABLE);
	Timed(!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_MODE_SELECT));

	// Send Address  EV5

	I2C_Send7bitAddress(I2Cx, SlaveAddress, I2C_Direction_Transmitter);
    //Timed(!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED));

	// EV6

	// Write first byte EV8_1

	I2C_SendData(I2Cx, *buf++);

	while (--nbyte) {

	  // wait on BTF

      //Timed(!I2C_GetFlagStatus(I2Cx, I2C_FLAG_BTF));
	  I2C_SendData(I2Cx, *buf++);
	}

    //Timed(!I2C_GetFlagStatus(I2Cx, I2C_FLAG_BTF));
	I2C_GenerateSTOP(I2Cx, ENABLE);
    //Timed(I2C_GetFlagStatus(I2C1, I2C_FLAG_STOPF));
      }
    return Success;
 errReturn:
    return Error;
}

uint32_t AT24_Read(uint16_t Addr, uint8_t *pdata, int size)
{
  uint32_t Timeout;
   
  I2C_AcknowledgeConfig(I2C1, ENABLE);
    
  Timeout = I2C_TIMEOUT;   
  while(I2C_GetFlagStatus(I2C1, I2C_FLAG_BUSY)) { if((Timeout--) == 0) return 1; }
 
  I2C_GenerateSTART(I2C1, ENABLE);
 
  Timeout = I2C_TIMEOUT;   
  while(!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT)) { if((Timeout--) == 0) return 1; }
 
  I2C_Send7bitAddress(I2C1, 0xA0, I2C_Direction_Transmitter);

  Timeout = I2C_TIMEOUT;   
  while(!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED)) { if((Timeout--) == 0) return 1; }
 
  I2C_SendData(I2C1, (uint8_t)((Addr & 0xFF00) >> 8));
 
  Timeout = I2C_TIMEOUT;   
  while(!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_TRANSMITTED)) { if((Timeout--) == 0) return 1; }
 
  I2C_SendData(I2C1, (uint8_t)(Addr & 0x00FF));
 
  Timeout = I2C_TIMEOUT;   
  while(!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_TRANSMITTED)) { if((Timeout--) == 0) return 0; }
 
  I2C_GenerateSTART(I2C1, ENABLE);
 
  Timeout = I2C_TIMEOUT;   
  while(!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT)) { if((Timeout--) == 0) return 1; }
 
  I2C_Send7bitAddress(I2C1, 0xA1, I2C_Direction_Receiver);
 
  while(size-- > 0)
  {
    Timeout = I2C_TIMEOUT;   
    while(!I2C_CheckEvent(I2C1,I2C_EVENT_MASTER_BYTE_RECEIVED))
    {
      if((Timeout--) == 0) return 1; 
    }
    *(pdata++) = I2C_ReceiveData(I2C1);
  }
  
  I2C_AcknowledgeConfig(I2C1, DISABLE);
  I2C_GenerateSTOP(I2C1, ENABLE);
  return 0;
}

uint8_t ucI2C_ReadAck(I2C_TypeDef* I2Cx) {
	uint8_t data;

	/* Enable ACK */
	I2Cx->CR1 |= I2C_CR1_ACK;

	/* Wait till not received */
	TM_I2C_Timeout = TM_I2C_TIMEOUT;
	while (!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_BYTE_RECEIVED)) {
		if (--TM_I2C_Timeout == 0x00) {
			return 1;
		}
	}

	/* Read data */
	data = I2Cx->DR;

	/* Return data */
	return data;
}

/**
  * @brief  This function handles the DMA Tx Channel interrupt Handler.
  *     @note This function should be called in the
  *       DMA1_CHANNEL2_3_IRQHandler in the stm8l15x_it.c file.
  *
  *       // INTERRUPT_HANDLER(DMA1_CHANNEL2_3_IRQHandler, 3)
  *       // {
  *           // sEE_I2C_DMA_TX_IRQHandler();
  *       // }
  * @param  None
  * @retval None
  */
void sEE_I2C_DMA_TX_IRQHandler(void)
{
    /* Check if the DMA transfer is complete */
    if (DMA_GetFlagStatus(sEE_I2C_DMA_FLAG_TX_TC) != RESET)
    {
        /* Disable the DMA Tx Channel and Clear all its Flags */
        DMA_Cmd(sEE_I2C_DMA_CHANNEL_TX, DISABLE);
        DMA_ClearFlag(sEE_I2C_DMA_FLAG_TX_TC);

        /*!< Wait till all data have been physically transferred on the bus */
        while (!I2C_CheckEvent(sEE_I2C, I2C_EVENT_MASTER_BYTE_TRANSMITTED))
        {}

        /*!< Send STOP condition */
        I2C_GenerateSTOP(sEE_I2C, ENABLE);

        /* Reset the variable holding the number of data to be written */
        *sEEDataWritePointer = 0;
    }
}

	u8 Temp_Read(void)
	{
		
		 u8 MSB,LSB;
		 
		//等待I2C閒置
		while(I2C_GetFlagStatus(I2C1,I2C_FLAG_BUSY));
		I2C_AcknowledgeConfig(I2C1,ENABLE); 
		//啟動訊號
		I2C_GenerateSTART(I2C1,ENABLE);	
		while(I2C_CheckEvent(I2C1,I2C_EVENT_MASTER_MODE_SELECT)!=SUCCESS);

		//發送裝置位置
		I2C_Send7bitAddress(I2C1,0xF0,I2C_Direction_Transmitter);
		while(I2C_CheckEvent(I2C1,I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED)!=SUCCESS);
		I2C_Cmd(I2C1,ENABLE);

		//發送記憶體位置
		I2C_SendData(I2C1,0xE5);
		while(I2C_CheckEvent(I2C1,I2C_EVENT_MASTER_BYTE_TRANSMITTED)!=SUCCESS);

		//啟動訊號
		I2C_GenerateSTART(I2C1,ENABLE);	
		while(I2C_CheckEvent(I2C1,I2C_EVENT_MASTER_MODE_SELECT)!=SUCCESS);
		
		//發送裝置位置
		I2C_Send7bitAddress(I2C1,0xF0,I2C_Direction_Receiver);
		while(I2C_CheckEvent(I2C1,I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED)!=SUCCESS);

		//I2C_AcknowledgeConfig(I2C1,DISABLE); //ACK 關閉	
		MSB=I2C_ReceiveData(I2C1);
	
		while(I2C_CheckEvent(I2C1,I2C_EVENT_MASTER_BYTE_RECEIVED)!=SUCCESS);
		
		LSB=I2C_ReceiveData(I2C1);
	
		while(I2C_CheckEvent(I2C1,I2C_EVENT_MASTER_BYTE_RECEIVED)!=SUCCESS);
		
		 	//停止訊號
		I2C_GenerateSTOP(I2C1,ENABLE);
			
		USART_SendData(USART1,MSB);
	
	}

uint8_t sensor_read(uint8_t sensor_address, uint8_t SUB)//read a byte from sensor
{ 
	uint8_t data;  

	/* Send START condition */ 
	I2C_GenerateSTART(I2C2, ENABLE); 

	/* Test on EV5 and clear it */ 
	while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_MODE_SELECT)); 

	/* In the case of a single data transfer disable ACK before reading the data */ 
    I2C_AcknowledgeConfig(I2C2, DISABLE); 

	/* Send EEPROM address for write */ 
	sensor_address=sensor_address|0x01;
	I2C_Send7bitAddress(I2C2, sensor_address, I2C_Direction_Transmitter); //0xD2

	/* Test on EV6 and clear it */ 
	while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED)); 

	/* Send the EEPROM's internal address to write to */ 
	I2C_SendData(I2C2, SUB);  

	/* Test on EV8 and clear it */ 
	while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_BYTE_TRANSMITTED)); 

	/* Send STRAT condition a second time */ 
	I2C_GenerateSTART(I2C2, ENABLE); 

	/* Test on EV5 and clear it */ 
	while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_MODE_SELECT)); 

	/* Send EEPROM address for read */ 
	I2C_Send7bitAddress(I2C2, sensor_address, I2C_Direction_Receiver); 

	/* Test on EV6 and clear it */ 
	while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED)); 

	/* Send STOP Condition */ 
    I2C_GenerateSTOP(I2C2, ENABLE); 

	/* Test on EV7 and clear it */ 
	while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_BYTE_RECEIVED));    

	/* Read a byte from the EEPROM */ 
    data = I2C_ReceiveData(I2C2);   
	
	return data;   
} 

 uint32_t I2C_Read_Buf(uint8_t* buf_ptr, uint32_t len){
	 uint32_t nbytes = 0;
	 I2C_AcknowledgeConfig(I2Cx, ENABLE);

	     for (nbytes = 0; nbytes < (int) len; nbytes++) {
	         /* Send NACK on the last byte */
	         if (nbytes == ((int) len - 1)) {
	             I2C_AcknowledgeConfig(I2Cx, DISABLE);

	             /* Send STOP Condition */
	             I2C_GenerateSTOP(I2Cx, ENABLE);
	         }

	         while(!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_BYTE_RECEIVED)){}

	         /* Read a byte from the slave */
	         buf_ptr[nbytes] = I2C_ReceiveData(I2Cx);
	     }

	 return nbytes;
 }

void ITG3200_read_burst(I2C_TypeDef * I2Cx, uint8_t devwrite ,uint8_t * data_out, uint8_t nBytes){

     // I2C_read_burst(I2Cx, slave_addr,ITG3200_XOUT_H, data_out, nBytes);

    I2C_start(I2Cx, devwrite, I2C_Direction_Transmitter);
    I2C_SendData(I2Cx,ITG3200_XOUT_H);
    while (I2C_GetFlagStatus(I2Cx, I2C_FLAG_BTF) == RESET);
    I2C_stop(I2Cx);
    I2C_start(I2Cx,devwrite, I2C_Direction_Receiver);
    I2C_AcknowledgeConfig(I2Cx, ENABLE);

    for(int i= 0; i < nBytes;  i++) {

      while( !I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_BYTE_RECEIVED) );
        data_out[i] = I2C_ReceiveData(I2Cx);
      }
      //set the stack pointer to X MSB
      //I2C_SendData(I2Cx,HMC8883_DATA_OUT_X_MSB_REG_ADDR);
      I2C_AcknowledgeConfig(I2Cx, DISABLE);
      I2C_stop(I2Cx);
}

/**
	*************************************************************************************
  * @brief  read one byte without acknowledge and end conversation
  * @param  None
  * @retval the received byte
	**************************************************************************************
  */
static uint8_t readEndByteI2C(void){
	
	/* buffer for the received byte */
	uint8_t ReceivedByte;
	
	/* disabe acknowledge of received data */
	I2C_AcknowledgeConfig(I2C, DISABLE);
	
	/* wait until one byte has been received */
	while( !I2C_CheckEvent(I2C, I2C_EVENT_MASTER_BYTE_RECEIVED) );
	
	
	/* read data from I2C data register and return data byte */
	ReceivedByte = I2C_ReceiveData(I2C);
	
	/* send stop condition */
	I2C_GenerateSTOP(I2C, ENABLE);
	
	/* return value */
	return ReceivedByte;
}

int i2c_read(i2c_t *obj, int address, char *data, int length, int stop) {
    I2C_TypeDef *i2c = (I2C_TypeDef *)(obj->i2c);
    int timeout;
    int count;
    int value;

    if (length == 0) return 0;

    i2c_start(obj);

    // Send slave address for read
    I2C_Send7bitAddress(i2c, address, I2C_Direction_Receiver);

    // Wait address is acknowledged
    timeout = FLAG_TIMEOUT;
    while (I2C_CheckEvent(i2c, I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED) == ERROR) {
        timeout--;
        if (timeout == 0) {
            return 0;
        }
    }

    // Read all bytes except last one
    for (count = 0; count < (length - 1); count++) {
        value = i2c_byte_read(obj, 0);
        data[count] = (char)value;
    }

    // If not repeated start, send stop.
    // Warning: must be done BEFORE the data is read.
    if (stop) {
        i2c_stop(obj);
    }

    // Read the last byte
    value = i2c_byte_read(obj, 1);
    data[count] = (char)value;

    return length;
}

void I2C_ReadSByte1(u8 id,u16 addr ,u8* pBuffer,u16 no)
{
    if(no==0)
		return;	
	while(I2C_GetFlagStatus(I2C2, I2C_FLAG_BUSY));		
	/*允许1字节1应答模式*/
	I2C_AcknowledgeConfig(I2C2, ENABLE);
	/* 发送起始位 */
    I2C_GenerateSTART(I2C2, ENABLE);
    while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_MODE_SELECT));/*EV5,主模式*/	
    /*发送器件地址(写)*/
    I2C_Send7bitAddress(I2C2,  id&0xfe, I2C_Direction_Transmitter);
    while (!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED));
	
	/*发送地址*/
	I2C_SendData(I2C2, addr>>8);
    while (!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_BYTE_TRANSMITTED));/*数据已发送*/		
	I2C_SendData(I2C2, addr);
    while (!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_BYTE_TRANSMITTED));/*数据已发送*/		
	
	/*起始位*/
	I2C_GenerateSTART(I2C2, ENABLE);
	while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_MODE_SELECT));	
	/*器件读*/
	I2C_Send7bitAddress(I2C2, id|I2C_READ, I2C_Direction_Receiver);
	while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED));
    while (no)
    {
		if(no==1)
		{
     		I2C_AcknowledgeConfig(I2C2, DISABLE);	//最后一位后要关闭应答的
    		I2C_GenerateSTOP(I2C2, ENABLE);			//发送停止位
		}	    
		while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_BYTE_RECEIVED)); /* EV7 */
	    *pBuffer = I2C_ReceiveData(I2C2);
	    pBuffer++;
	    /* Decrement the read bytes counter */
	    no--;
    }
	//再次允许应答模式
	I2C_AcknowledgeConfig(I2C2, ENABLE);
}

void i2cRead(uint8_t device, uint8_t address, uint8_t *data, uint8_t length)
{
	i2cSendAddress(device, READ, address);

	int i;
	for(i = 0; i<length; i++)
	{
		/* Test on EV7 and clear it */
		while(!I2C_CheckEvent(I2C_BUS, I2C_EVENT_MASTER_BYTE_RECEIVED));

		*data = I2C_ReceiveData(I2C_BUS);
		data++;

		 /* Disable Acknowledgement */
        if(!(i < (length - 1)))
            I2C_AcknowledgeConfig(I2C_BUS, DISABLE);

	}

    /* Send STOP Condition */
    I2C_GenerateSTOP(I2C_BUS, ENABLE);
}

short read8(I2C_TypeDef* I2Cx){
	uint8_t msb=0, lsb=0;
	unsigned char dummy1;
	unsigned short data;

	I2C_AcknowledgeConfig(I2Cx, ENABLE);
	while(I2C_GetFlagStatus(I2Cx, I2C_FLAG_BUSY));

	I2C_GenerateSTART(I2Cx, ENABLE);
	while(!I2C_GetFlagStatus(I2Cx, I2C_FLAG_SB));
	while(!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_MODE_SELECT));

	I2C_Send7bitAddress(I2Cx,0x6B<<1,I2C_Direction_Transmitter);
	while(!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED));

	I2C_SendData(I2Cx,0x28);
	while(!I2C_GetFlagStatus(I2Cx,I2C_FLAG_TXE));
	while(!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_BYTE_TRANSMITTED));

	I2C_GenerateSTART(I2Cx, ENABLE);
	while(!I2C_GetFlagStatus(I2Cx, I2C_FLAG_SB));

	I2C_Send7bitAddress(I2Cx, 0x6B<<1, I2C_Direction_Receiver);
	while (!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED));

	msb = I2C_ReceiveData(I2Cx);
	while(!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_BYTE_RECEIVED));

	I2C_NACKPositionConfig(I2Cx, I2C_NACKPosition_Current);
	I2C_AcknowledgeConfig(I2Cx, DISABLE);

	lsb = I2C_ReceiveData(I2Cx);
	while(!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_BYTE_RECEIVED));

	//dummy1 = I2C_ReceiveData(I2Cx);
	//while(!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_BYTE_RECEIVED));

	I2C_GenerateSTOP(I2Cx, ENABLE);
	while(I2C_GetFlagStatus(I2Cx, I2C_FLAG_STOPF));


	data  = msb<<8;
	data |= lsb;

	return data;
}