C++ GAPRole_SetParameter函数代码示例

/*********************************************************************
 * @fn      processGapStateChange
 *
 * @brief   Change the GAP state.
 *          1. Connected -> disconnect and start advertising
 *          2. Advertising -> stop advertising
 *          3. Disconnected/not advertising -> start advertising
 *
 * @param   none
 *
 * @return  none
 */
static void processGapStateChange(void)
{
  if (gapProfileState != GAPROLE_CONNECTED)
  {
    uint8_t current_adv_enabled_status;
    uint8_t new_adv_enabled_status;

    // Find the current GAP advertising status
    GAPRole_GetParameter(GAPROLE_ADVERT_ENABLED, &current_adv_enabled_status);

    if (current_adv_enabled_status == FALSE)
    {
      new_adv_enabled_status = TRUE;
    }
    else
    {
      new_adv_enabled_status = FALSE;
    }

    // Change the GAP advertisement status to opposite of current status
    GAPRole_SetParameter(GAPROLE_ADVERT_ENABLED, sizeof(uint8_t),
                         &new_adv_enabled_status);
  }

  if (gapProfileState == GAPROLE_CONNECTED)
  {
    uint8_t adv_enabled = TRUE;

    // Disconnect
    GAPRole_TerminateConnection();

    // Start advertising
    GAPRole_SetParameter(GAPROLE_ADVERT_ENABLED, sizeof(uint8_t), &adv_enabled);
  }
}

/*********************************************************************
 * @fn      simpleBLEBroadcaster_HandleKeys
 *
 * @brief   Handles all key events for this device.
 *
 * @param   shift - true if in shift/alt.
 * @param   keys - bit field for key events. Valid entries:
 *                 HAL_KEY_SW_2
 *                 HAL_KEY_SW_1
 *
 * @return  none
 */
static void simpleBLEBroadcaster_HandleKeys( uint8 shift, uint8 keys )
{
  VOID shift;  // Intentionally unreferenced parameter

  if ( keys & HAL_KEY_SW_1 )
  {
    advertData[6]++;
    
    GAPRole_SetParameter( GAPROLE_ADVERT_DATA, sizeof( advertData ), advertData );
  }
  
  if ( keys & HAL_KEY_SW_2 )
  {
    // ressing the right key should toggle advertising on and off
    uint8 current_adv_enabled_status;
    uint8 new_adv_enabled_status;
    
    //Find the current GAP advertisement status
    GAPRole_GetParameter( GAPROLE_ADVERT_ENABLED, &current_adv_enabled_status );
    
    if( current_adv_enabled_status == FALSE )
    {
      new_adv_enabled_status = TRUE;
    }
    else
    {
      new_adv_enabled_status = FALSE;
    }
    
    //change the GAP advertisement status to opposite of current status
    GAPRole_SetParameter( GAPROLE_ADVERT_ENABLED, sizeof( uint8 ), &new_adv_enabled_status );
  }
}

/*********************************************************************
 * @fn      simpleTopology_init
 *
 * @brief   Called during initialization and contains application
 *          specific initialization (ie. hardware initialization/setup,
 *          table initialization, power up notification, etc), and
 *          profile initialization/setup.
 *
 * @param   None.
 *
 * @return  None.
 */
static void simpleTopology_init(void)
{
	// ******************************************************************
	// N0 STACK API CALLS CAN OCCUR BEFORE THIS CALL TO ICall_registerApp
	// ******************************************************************
	// Register the current thread as an ICall dispatcher application
	// so that the application can send and receive messages.
	ICall_registerApp(&selfEntity, &sem);

	// Create an RTOS queue for message from profile to be sent to app.
	appMsgQueue = Util_constructQueue(&appMsg);

	Util_constructClock(&scanClock, SensorTagMultiRoleTest_scanStartHandler,
			SCAN_EVENT_PERIOD, SCAN_EVENT_PERIOD, TRUE, SCAN_EVENT);

	// Setup the GAP
	{
		/*-------------------PERIPHERAL-------------------*/
		uint16_t advInt = DEFAULT_ADVERTISING_INTERVAL;
		GAP_SetParamValue(TGAP_LIM_DISC_ADV_INT_MIN, advInt);
		GAP_SetParamValue(TGAP_LIM_DISC_ADV_INT_MAX, advInt);
		GAP_SetParamValue(TGAP_GEN_DISC_ADV_INT_MIN, advInt);
		GAP_SetParamValue(TGAP_GEN_DISC_ADV_INT_MAX, advInt);

		GAP_SetParamValue(TGAP_LIM_ADV_TIMEOUT, ADV_DURATION);

		/*-------------------CENTRAL-------------------*/
		GAP_SetParamValue(TGAP_GEN_DISC_SCAN, DEFAULT_SCAN_DURATION);
		GAP_SetParamValue(TGAP_GEN_DISC_SCAN_INT, DEFAULT_SCAN_INT);
		GAP_SetParamValue(TGAP_GEN_DISC_SCAN_WIND, DEFAULT_SCAN_WIND);
		GAP_SetParamValue(TGAP_LIM_DISC_SCAN_INT, DEFAULT_SCAN_INT);
		GAP_SetParamValue(TGAP_LIM_DISC_SCAN_WIND, DEFAULT_SCAN_WIND);
	}

	// Setup the GAP Role Profile
	{
		/*--------PERIPHERAL-------------*/
		// For all hardware platforms, device starts advertising upon initialization
		uint8_t initialAdvertEnable = FALSE;
		// By setting this to zero, the device will go into the waiting state after
		// being discoverable for 30.72 second, and will not being advertising again
		// until the enabler is set back to TRUE
		uint16_t advertOffTime = 0;

		GAPRole_SetParameter(GAPROLE_ADVERT_ENABLED, sizeof(uint8_t),
				&initialAdvertEnable, NULL);
		GAPRole_SetParameter(GAPROLE_ADVERT_OFF_TIME, sizeof(uint16_t),
				&advertOffTime, NULL);
		GAPRole_SetParameter(GAPROLE_ADVERT_DATA, sizeof(advertData), advertData, NULL);

		// Register with GAP for HCI/Host messages
		GAP_RegisterForMsgs(selfEntity);
	}

	VOID GAPRole_StartDevice(&simpleTopology_gapRoleCBs);
}

/**
 *  @fn      SNP_stopAdv
 *
 */
uint8_t SNP_stopAdv(void)
{
  //Disable Advertising.
  uint8_t start = FALSE;
  GAPRole_SetParameter(GAPROLE_ADVERT_ENABLED, sizeof(uint8_t),
                       &start);
  GAPRole_SetParameter(GAPROLE_ADV_NONCONN_ENABLED, sizeof(uint8_t),
                       &start);
  return SNP_SUCCESS;
}

/*********************************************************************
 * @fn      CyclingSensor_handleResetEvt
 *
 * @brief   "soft" resets the device.  This puts the device into a waiting 
 *           state, clears all white list, bonding and GATT service handle 
 *           information about previously previously connected devices.
 *
 * @param   none
 *
 * @return  none
 */
static void CyclingSensor_handleResetEvt(void)
{
  static uint8_t isWLClear = FALSE;
  
  if (gapProfileState == GAPROLE_CONNECTED)
  { 
    // Exit the connection.
    GAPRole_TerminateConnection();
  }
  else if (gapProfileState == GAPROLE_ADVERTISING)
  {
    uint8_t value = FALSE;

    // Turn off advertising.
    GAPRole_SetParameter(GAPROLE_ADVERT_ENABLED, sizeof(uint8_t), &value);
  }
  else if (USING_WHITE_LIST == TRUE && isWLClear == FALSE)
  {
    // Set internal white list flag to true.
    isWLClear = TRUE;
    
    // Disable white list use with advertising.
    sensorUsingWhiteList = FALSE;
    
    // Temporary variable.
    uint8_t value = GAP_FILTER_POLICY_ALL;

    // Turn off white list filter policy.
    GAPRole_SetParameter(GAPROLE_ADV_FILTER_POLICY, sizeof(uint8_t), &value);

    // Clear the white list.
    HCI_LE_ClearWhiteListCmd();
  }
  else if ((gapProfileState == GAPROLE_STARTED) ||
            (gapProfileState == GAPROLE_WAITING) ||
            (gapProfileState == GAPROLE_WAITING_AFTER_TIMEOUT))
  {
    uint8_t eraseBonds = TRUE;

    // Stop the periodic expirations of the reset clock.
    Util_stopClock(&resetClock);
    
    // Set internal white list flag to false for next reset event.
    isWLClear = FALSE;
    
    // Erase all bonds.
    GAPBondMgr_SetParameter(GAPBOND_ERASE_ALLBONDS, 0, &eraseBonds);
    
    // Turn on GREEN LED for set time.
    //HalLedSet(HAL_LED_1, HAL_LED_MODE_BLINK);
  }  
}

static void FanPeripheralStateNotificationCallBack(gaprole_States_t newState)
{
	switch (newState)
	{
		case GAPROLE_STARTED:
			{
				uint8 ownAddress[B_ADDR_LEN];
				uint8 systemId[DEVINFO_SYSTEM_ID_LEN];

				GAPRole_GetParameter(GAPROLE_BD_ADDR, ownAddress);

				// use 6 bytes of device address for 8 bytes of system ID value
				systemId[0] = ownAddress[0];
				systemId[1] = ownAddress[1];
				systemId[2] = ownAddress[2];

				// set middle bytes to zero
				systemId[4] = 0x00;
				systemId[3] = 0x00;

				// shift three bytes up
				systemId[7] = ownAddress[5];
				systemId[6] = ownAddress[4];
				systemId[5] = ownAddress[3];

				DevInfo_SetParameter(DEVINFO_SYSTEM_ID, DEVINFO_SYSTEM_ID_LEN, systemId);
			}
			break;
		case GAPROLE_ADVERTISING:
			break;
		case GAPROLE_CONNECTED:
			FanConnected(fanTaskId);
			break;
		case GAPROLE_WAITING:
			{
				FanDisConnected();
				uint8 advertEnabled = FALSE;
				GAPRole_SetParameter(GAPROLE_ADVERT_ENABLED, sizeof(uint8), &advertEnabled); 
				GAPRole_SetParameter(GAPROLE_SCAN_RSP_DATA, sizeof(scanResponseData), scanResponseData);
				GGS_SetParameter(GGS_DEVICE_NAME_ATT, GAP_DEVICE_NAME_LEN, scanResponseData + 2);
				advertEnabled = TRUE;
				GAPRole_SetParameter(GAPROLE_ADVERT_ENABLED, sizeof(uint8), &advertEnabled);			
			}
			break;
		case GAPROLE_WAITING_AFTER_TIMEOUT:
			break;
		case GAPROLE_ERROR:
			break;
		default:
			break;
	}
};

/**
 *  SNP_setAdvData
 *
 */
uint8_t SNP_setAdvData(snpSetAdvDataReq_t *pReq, uint8_t len)
{
  uint8_t status = 0;
  uint8_t *pDataPtr;
  
  //Device must be started, or the set adv command will failed.
  VOID GAPRole_StartDevice(&SNP_gapRoleCBs);  
  
  if(pReq->type < SNP_ADV_DATA_MAX_IDX)
  {
    pDataPtr = advPtrTable[pReq->type].pData;
    if(pDataPtr)
    {
      ICall_free(advPtrTable[pReq->type].pData);
    }
    advPtrTable[pReq->type].pData = pDataPtr = ICall_malloc(len);
    if(pDataPtr)
    {
      advPtrTable[pReq->type].length = len;
      memcpy(pDataPtr, pReq->pData, len);
      if(pReq->type == SNP_ADV_DATA_SCAN_RSP_IDX)
      {
        status = GAPRole_SetParameter(GAPROLE_SCAN_RSP_DATA, len, pDataPtr);
      }
      else if(pReq->type == SNP_ADV_DATA_NON_CONN_IDX)
      {
        status = GAPRole_SetParameter(GAPROLE_ADVERT_DATA, len, pDataPtr);
      }
      else if(pReq->type == SNP_ADV_DATA_CONN_IDX)
      {
        uint8_t value;
        GAPRole_GetParameter(GAPROLE_STATE, &value);
        if(value == GAPROLE_CONNECTED_ADV)
        {
          status = GAPRole_SetParameter(GAPROLE_ADVERT_DATA, len, pDataPtr);        
        }      
      }
    }
    else
    {
      status = SNP_OUT_OF_RESOURCES;
    }      
  }
  else
  {
    //Error, bad type
    status = SNP_INVALID_PARAMS;
  }  
  return status;
}

/*********************************************************************
 * @fn      hidDevInitialAdvertising
 *
 * @brief   Start advertising for initial connection
 *
 * @return  None.
 */
static void hidDevInitialAdvertising( void )
{
  uint8 param;

  VOID GAP_SetParamValue( TGAP_LIM_DISC_ADV_INT_MIN, HID_INITIAL_ADV_INT_MIN );
  VOID GAP_SetParamValue( TGAP_LIM_DISC_ADV_INT_MAX, HID_INITIAL_ADV_INT_MAX );
  VOID GAP_SetParamValue( TGAP_LIM_ADV_TIMEOUT, HID_INITIAL_ADV_TIMEOUT );

  // Setup adverstising filter policy first
  param = GAP_FILTER_POLICY_ALL;
  VOID GAPRole_SetParameter( GAPROLE_ADV_FILTER_POLICY, sizeof( uint8 ), &param );

  param = TRUE;
  VOID GAPRole_SetParameter( GAPROLE_ADVERT_ENABLED, sizeof( uint8 ), &param );
}

void MysensorTag_updateAdvertisingData(void)
{

 uint16_t RawTemperature, RawHumidity;
 bStatus_t st1,st2,st3, st4;
 uint8_t period, config, HumiditySensorON=1;
 uint8_t HumRawData[4]; // humidity sensor raw data
 float temperature,humidity; // temperature and humidity measurements in Celcius and %

// set parameter
 st1 =  Humidity_setParameter(SENSOR_CONF,1,&HumiditySensorON); // turn on
 //SensorTagHum_processCharChangeEvt(SENSOR_CONF); // enable humidity sensing
 // SensorTag_enqueueMsg(ST_CHAR_CHANGE_EVT, SERVICE_ID_HUM, SENOSR_CONF);


 // get parameter
 st2 =  Humidity_getParameter(SENSOR_PERI, &period);
 st3 =  Humidity_getParameter(SENSOR_CONF, &config);
 st4 =  Humidity_getParameter(SENSOR_DATA, &HumRawData);

 // raw temperature and humidity
 RawTemperature = HumRawData[0] | (HumRawData[1]<<8);
 RawHumidity = HumRawData[2] | (HumRawData[3]<<8);
 sensorHdc1000Convert(RawTemperature, RawHumidity,&temperature, &humidity);

 // update advertisement data
 advertData[KEY_STATE_OFFSET+1] = (uint8_t)temperature;
 advertData[KEY_STATE_OFFSET+2] = (uint8_t)humidity;
 GAPRole_SetParameter(GAPROLE_ADVERT_DATA, sizeof(advertData), advertData);
}

/*********************************************************************
 * @fn      softCmd_HandleKeys
 *
 * @brief   Handles all key events for this device.
 *
 * @param   shift - true if in shift/alt.
 * @param   keys - bit field for key events. Valid entries:
 *                 HAL_KEY_SW_2
 *                 HAL_KEY_SW_1
 *
 * @return  none
 */
static void softCmd_HandleKeys( uint8 shift, uint8 keys )
{
  if ( keys & HAL_KEY_SW_1 )
  {
    // if in a connection send a soft key
    if ( softCmdGapState == GAPROLE_CONNECTED )
    {
      softCmdSend( CMD_ENUM_SOFT_CMD_0 );
    }
  }
  
  if ( keys & HAL_KEY_SW_2 )
  {
    // if not in a connection, toggle advertising on and off
    if( softCmdGapState != GAPROLE_CONNECTED )
    {
      uint8 status;
      
      // toggle GAP advertisement status
      GAPRole_GetParameter( GAPROLE_ADVERT_ENABLED, &status );
      status = !status;
      GAPRole_SetParameter( GAPROLE_ADVERT_ENABLED, sizeof( uint8 ), &status );   
    }
    // if in a connection send a soft key
    else
    {
      softCmdSend( CMD_ENUM_SOFT_CMD_1 );
    }
  }
}

/*********************************************************************
 * @fn      timeAppDisconnected
 *
 * @brief   Handle disconnect. 
 *
 * @return  none
 */
static void timeAppDisconnected( void )
{
  // Initialize state variables
  timeAppDiscState = DISC_IDLE;
  timeAppPairingStarted = FALSE;
  timeAppDiscPostponed = FALSE;
  
   
  // stop periodic measurement
  osal_stop_timerEx( bloodPressureTaskId, BP_TIMER_CUFF_EVT ); 
  

  // reset bloodPressure measurement client configuration
  uint16 param = 0;
  BloodPressure_SetParameter(BLOODPRESSURE_MEAS_CHAR_CFG, sizeof(uint16), (uint8 *) &param);

  // reset bloodPressure intermediate measurement client configuration
  BloodPressure_SetParameter(BLOODPRESSURE_IMEAS_CHAR_CFG, sizeof(uint16), (uint8 *) &param);

  
  uint8 advEnable = FALSE;
  
  //disable advertising on disconnect
  GAPRole_SetParameter( GAPROLE_ADVERT_ENABLED, sizeof( uint8 ), &advEnable );
  
}

/*---------------------------------------------------------------------------
* Add the set the last part of hte device name to the final bytes of the 
* device address. Useful when mane demo devices are located in the same room.
*-------------------------------------------------------------------------*/
void updateNameWithAddressInfo(void)
{
  //uint8 status;
  uint8 numberString[4];
  uint8 address[6];
  uint8 value;

  //status = GAPRole_GetParameter(GAPROLE_BD_ADDR, address);
  GAPRole_GetParameter(GAPROLE_BD_ADDR, address);

  value = (address[1] & 0xF0) >> 4;
  numberString[0] = getAscii(value);

  value = address[1] & 0x0F;
  numberString[1] = getAscii(value);     

  value = (address[0] & 0xF0) >> 4;
  numberString[2] = getAscii(value);

  value = address[0] & 0x0F;
  numberString[3] = getAscii(value);     

  // Replace "0000" part of "OLP425-0000"
  osal_memcpy(&attDeviceName[7], numberString, 4);
  osal_memcpy(&deviceName[9], numberString, 4);
  
  osal_memcpy(&attDeviceNameNew[7], numberString, 4);
  osal_memcpy(&deviceNameNew[9], numberString, 4);

//  status = GAPRole_SetParameter( GAPROLE_SCAN_RSP_DATA, sizeof ( deviceName ), deviceName );
//  status = GGS_SetParameter( GGS_DEVICE_NAME_ATT, GAP_DEVICE_NAME_LEN - 1, attDeviceName );   

  GAPRole_SetParameter( GAPROLE_SCAN_RSP_DATA, sizeof ( deviceName ), deviceName );
  GGS_SetParameter( GGS_DEVICE_NAME_ATT, GAP_DEVICE_NAME_LEN - 1, attDeviceName );   
}

/*********************************************************************
 * @fn      SimpleBLEPeripheral_ProcessEvent
 *
 * @brief   Simple BLE Peripheral Application Task event processor.  This function
 *          is called to process all events for the task.  Events
 *          include timers, messages and any other user defined events.
 *
 * @param   task_id  - The OSAL assigned task ID.
 * @param   events - events to process.  This is a bit map and can
 *                   contain more than one event.
 *
 * @return  events not processed
 */
uint16 SimpleBLEPeripheral_ProcessEvent( uint8 task_id, uint16 events )
{

  VOID task_id; // OSAL required parameter that isn't used in this function

  if ( events & SYS_EVENT_MSG )
  {
    uint8 *pMsg;

    if ( (pMsg = osal_msg_receive( simpleBLEPeripheral_TaskID )) != NULL )
    {
      simpleBLEPeripheral_ProcessOSALMsg( (osal_event_hdr_t *)pMsg );

      // Release the OSAL message
      VOID osal_msg_deallocate( pMsg );
    }

    // return unprocessed events
    return (events ^ SYS_EVENT_MSG);
  }

  if ( events & SBP_START_DEVICE_EVT )
  {
    P0_7 = 0;  //防止继电器跳变，初始化为高
    P0DIR |= BV(7); //设置为输出
    P0SEL &=~BV(7); //设置该脚为普通GPIO
    //HCI_EXT_SetTxPowerCmd (HCI_EXT_TX_POWER_MINUS_23_DBM);
    // Start the Device
    VOID GAPRole_StartDevice( &simpleBLEPeripheral_PeripheralCBs );

    // Start Bond Manager
    VOID GAPBondMgr_Register( &simpleBLEPeripheral_BondMgrCBs );

    return ( events ^ SBP_START_DEVICE_EVT );
  }

  if ( events & SBP_PERIODIC_EVT )
  {
    //成功写入后，重启从机
    HAL_SYSTEM_RESET();
    return (events ^ SBP_PERIODIC_EVT);
  }

#if defined ( PLUS_BROADCASTER )
  if ( events & SBP_ADV_IN_CONNECTION_EVT )
  {
    uint8 turnOnAdv = TRUE;
    // Turn on advertising while in a connection
    GAPRole_SetParameter( GAPROLE_ADVERT_ENABLED, sizeof( uint8 ), &turnOnAdv );

    return (events ^ SBP_ADV_IN_CONNECTION_EVT);
  }
#endif // PLUS_BROADCASTER

  // Discard unknown events
  return 0;
}

/*---------------------------------------------------------------------------
* Initialization of GAP properties. 
*-------------------------------------------------------------------------*/
static void gapApplicationInit(void)
{
  // For the CC2540DK-MINI keyfob, device doesn't start advertising until button is pressed
  uint8 initial_advertising_enable = TRUE;
  // By setting this to zero, the device will go into the waiting state after
  // being discoverable for 30.72 second, and will not being advertising again
  // until the enabler is set back to TRUE
  uint16 gapRole_AdvertOffTime = 0;

  uint8 enable_update_request = DEFAULT_ENABLE_UPDATE_REQUEST;
  uint16 desired_min_interval = DEFAULT_DESIRED_MIN_CONN_INTERVAL;
  uint16 desired_max_interval = DEFAULT_DESIRED_MAX_CONN_INTERVAL;
  uint16 desired_slave_latency = DEFAULT_DESIRED_SLAVE_LATENCY;
  uint16 desired_conn_timeout = DEFAULT_DESIRED_CONN_TIMEOUT;

  // Set the GAP Role Parameters
  GAPRole_SetParameter( GAPROLE_ADVERT_ENABLED, sizeof( uint8 ), &initial_advertising_enable );
  GAPRole_SetParameter( GAPROLE_ADVERT_OFF_TIME, sizeof( uint16 ), &gapRole_AdvertOffTime );

  GAPRole_SetParameter( GAPROLE_SCAN_RSP_DATA, sizeof ( deviceName ), deviceName );
  GAPRole_SetParameter( GAPROLE_ADVERT_DATA, sizeof( advertData ), advertData );

  GAPRole_SetParameter( GAPROLE_PARAM_UPDATE_ENABLE, sizeof( uint8 ), &enable_update_request );
  GAPRole_SetParameter( GAPROLE_MIN_CONN_INTERVAL, sizeof( uint16 ), &desired_min_interval );
  GAPRole_SetParameter( GAPROLE_MAX_CONN_INTERVAL, sizeof( uint16 ), &desired_max_interval );
  GAPRole_SetParameter( GAPROLE_SLAVE_LATENCY, sizeof( uint16 ), &desired_slave_latency );
  GAPRole_SetParameter( GAPROLE_TIMEOUT_MULTIPLIER, sizeof( uint16 ), &desired_conn_timeout );

  // Set the GAP Attributes
  GGS_SetParameter( GGS_DEVICE_NAME_ATT, GAP_DEVICE_NAME_LEN, attDeviceName );

  // Setup the GAP Bond Manager
  {
    uint8 pairMode = GAPBOND_PAIRING_MODE_WAIT_FOR_REQ;
    uint8 mitm = TRUE;
    uint8 ioCap = GAPBOND_IO_CAP_DISPLAY_ONLY;
    uint8 bonding = TRUE;
    GAPBondMgr_SetParameter( GAPBOND_PAIRING_MODE, sizeof ( uint8 ), &pairMode );
    GAPBondMgr_SetParameter( GAPBOND_MITM_PROTECTION, sizeof ( uint8 ), &mitm );
    GAPBondMgr_SetParameter( GAPBOND_IO_CAPABILITIES, sizeof ( uint8 ), &ioCap );
    GAPBondMgr_SetParameter( GAPBOND_BONDING_ENABLED, sizeof ( uint8 ), &bonding );
  }  
  
  // Set max output power and reciever gain
  HCI_EXT_SetTxPowerCmd(HCI_EXT_TX_POWER_4_DBM);
  HCI_EXT_SetRxGainCmd(HCI_EXT_RX_GAIN_HIGH);
}

/*********************************************************************
 * @fn      performPeriodicTask
 *
 * @brief   Perform a periodic application task. This function gets
 *          called every five seconds as a result of the SBP_PERIODIC_EVT
 *          OSAL event. In this example, the value of the third
 *          characteristic in the SimpleGATTProfile service is retrieved
 *          from the profile, and then copied into the value of the
 *          the fourth characteristic.
 *
 * @param   none
 *
 * @return  none
 */
static void performPeriodicTask( void )
{
  uint8 pos = FALSE, txpwr = 0;

  Batt_MeasLevel( );
  GAPRole_SetParameter(GAPROLE_ADVERT_ENABLED, sizeof(uint8), &pos);

  advertData[11] = Battery2Asc(battLevel);
  advertData[12] = (P0 & 1<<4) ? 0x31 : 0x30;
  advertData[13] = (P0 & 1<<5) ? 0x31 : 0x30;
  advertData[14] = (P0 & 1<<6) ? 0x31 : 0x30;
  advertData[15] = '0' + advert_internal/100;
  advertData[16] = '0' + (advert_internal/10)%10;
  advertData[17] = '0' + advert_internal%10;
  ProxReporter_GetParameter(PP_TX_POWER_LEVEL, &txpwr);
  advertData[18] = txpwr + '0';

  HCI_LE_SetAdvDataCmd( sizeof( advertData ), advertData );
  pos = TRUE;
  GAPRole_SetParameter(GAPROLE_ADVERT_ENABLED, sizeof(uint8), &pos);
}