C++ CLEAR_BIT函数代码示例

/**
  * @brief  Disable the Debug Module during STANDBY mode       
  * @param  None
  * @retval None
  */
void HAL_DisableDBGStandbyMode(void)
{
  CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STANDBY);
}

/**
  * @brief Disables CORTEX M4 SEVONPEND bit. 
  * @note Clears SEVONPEND bit of SCR register. When this bit is set, this causes 
  *       WFE to wake up when an interrupt moves from inactive to pended.         
  * @retval None
  */
void HAL_PWR_DisableSEVOnPend(void)
{
  /* Clear SEVONPEND bit of Cortex System Control Register */
  CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk));
}

/**
  * @brief This function handles FLASH interrupt request.
  * @retval None
  */
void HAL_FLASH_IRQHandler(void)
{
  uint32_t addresstmp = 0;
  
  /* Check FLASH operation error flags */
  if( __HAL_FLASH_GET_FLAG(FLASH_FLAG_WRPERR)     || 
      __HAL_FLASH_GET_FLAG(FLASH_FLAG_PGAERR)     || 
      __HAL_FLASH_GET_FLAG(FLASH_FLAG_SIZERR)     || 
#if defined(FLASH_SR_RDERR)
      __HAL_FLASH_GET_FLAG(FLASH_FLAG_RDERR)      || 
#endif /* FLASH_SR_RDERR */
#if defined(FLASH_SR_OPTVERRUSR)
      __HAL_FLASH_GET_FLAG(FLASH_FLAG_OPTVERRUSR) || 
#endif /* FLASH_SR_OPTVERRUSR */
      __HAL_FLASH_GET_FLAG(FLASH_FLAG_OPTVERR) )
  {
    if(pFlash.ProcedureOnGoing == FLASH_PROC_PAGEERASE)
    {
      /* Return the faulty sector */
      addresstmp = pFlash.Page;
      pFlash.Page = 0xFFFFFFFFU;
    }
    else
    {
      /* Return the faulty address */
      addresstmp = pFlash.Address;
    }
    /* Save the Error code */
    FLASH_SetErrorCode();
    
    /* FLASH error interrupt user callback */
    HAL_FLASH_OperationErrorCallback(addresstmp);

    /* Stop the procedure ongoing */
    pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
  }

  /* Check FLASH End of Operation flag  */
  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP))
  {
    /* Clear FLASH End of Operation pending bit */
    __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP);
    
    /* Process can continue only if no error detected */
    if(pFlash.ProcedureOnGoing != FLASH_PROC_NONE)
    {
      if(pFlash.ProcedureOnGoing == FLASH_PROC_PAGEERASE)
      {
        /* Nb of pages to erased can be decreased */
        pFlash.NbPagesToErase--;

        /* Check if there are still pages to erase */
        if(pFlash.NbPagesToErase != 0)
        {
          addresstmp = pFlash.Page;
          /*Indicate user which sector has been erased */
          HAL_FLASH_EndOfOperationCallback(addresstmp);

          /*Increment sector number*/
          addresstmp = pFlash.Page + FLASH_PAGE_SIZE;
          pFlash.Page = addresstmp;

          /* If the erase operation is completed, disable the ERASE Bit */
          CLEAR_BIT(FLASH->PECR, FLASH_PECR_ERASE);

          FLASH_PageErase(addresstmp);
        }
        else
        {
          /* No more pages to Erase, user callback can be called. */
          /* Reset Sector and stop Erase pages procedure */
          pFlash.Page = addresstmp = 0xFFFFFFFFU;
          pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
          /* FLASH EOP interrupt user callback */
          HAL_FLASH_EndOfOperationCallback(addresstmp);
        }
      }
      else
      {
          /* If the program operation is completed, disable the PROG Bit */
          CLEAR_BIT(FLASH->PECR, FLASH_PECR_PROG);

          /* Program ended. Return the selected address */
          /* FLASH EOP interrupt user callback */
          HAL_FLASH_EndOfOperationCallback(pFlash.Address);
        
          /* Reset Address and stop Program procedure */
          pFlash.Address = 0xFFFFFFFFU;
          pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
      }
    }
  }
  

  if(pFlash.ProcedureOnGoing == FLASH_PROC_NONE)
  {
//.........这里部分代码省略.........

/**
  * @brief  De-initialize registers of the selected ADC instance
  *         to their default reset values.
  * @note   To reset all ADC instances quickly (perform a hard reset),
  *         use function @ref LL_ADC_CommonDeInit().
  * @note   If this functions returns error status, it means that ADC instance
  *         is in an unknown state.
  *         In this case, perform a hard reset using high level
  *         clock source RCC ADC reset.
  *         Refer to function @ref LL_ADC_CommonDeInit().
  * @param  ADCx ADC instance
  * @retval An ErrorStatus enumeration value:
  *          - SUCCESS: ADC registers are de-initialized
  *          - ERROR: ADC registers are not de-initialized
  */
ErrorStatus LL_ADC_DeInit(ADC_TypeDef *ADCx)
{
  ErrorStatus status = SUCCESS;
  
  __IO uint32_t timeout_cpu_cycles = 0U;
  
  /* Check the parameters */
  assert_param(IS_ADC_ALL_INSTANCE(ADCx));
  
  /* Disable ADC instance if not already disabled.                            */
  if(LL_ADC_IsEnabled(ADCx) == 1U)
  {
    /* Set ADC group regular trigger source to SW start to ensure to not      */
    /* have an external trigger event occurring during the conversion stop    */
    /* ADC disable process.                                                   */
    LL_ADC_REG_SetTriggerSource(ADCx, LL_ADC_REG_TRIG_SOFTWARE);
    
    /* Stop potential ADC conversion on going on ADC group regular.           */
    if(LL_ADC_REG_IsConversionOngoing(ADCx) != 0U)
    {
      if(LL_ADC_REG_IsStopConversionOngoing(ADCx) == 0U)
      {
        LL_ADC_REG_StopConversion(ADCx);
      }
    }
    
    /* Wait for ADC conversions are effectively stopped                       */
    timeout_cpu_cycles = ADC_TIMEOUT_STOP_CONVERSION_CPU_CYCLES;
    while (LL_ADC_REG_IsStopConversionOngoing(ADCx) == 1U)
    {
      if(timeout_cpu_cycles-- == 0U)
      {
        /* Time-out error */
        status = ERROR;
      }
    }
    
    /* Disable the ADC instance */
    LL_ADC_Disable(ADCx);
    
    /* Wait for ADC instance is effectively disabled */
    timeout_cpu_cycles = ADC_TIMEOUT_DISABLE_CPU_CYCLES;
    while (LL_ADC_IsDisableOngoing(ADCx) == 1U)
    {
      if(timeout_cpu_cycles-- == 0U)
      {
        /* Time-out error */
        status = ERROR;
      }
    }
  }
  
  /* Check whether ADC state is compliant with expected state */
  if(READ_BIT(ADCx->CR,
              (  ADC_CR_ADSTP | ADC_CR_ADSTART
               | ADC_CR_ADDIS | ADC_CR_ADEN   )
             )
     == 0U)
  {
    /* ========== Reset ADC registers ========== */
    /* Reset register IER */
    CLEAR_BIT(ADCx->IER,
              (  LL_ADC_IT_ADRDY
               | LL_ADC_IT_EOC
               | LL_ADC_IT_EOS
               | LL_ADC_IT_OVR
               | LL_ADC_IT_EOSMP
               | LL_ADC_IT_AWD1 )
             );
    
    /* Reset register ISR */
    SET_BIT(ADCx->ISR,
            (  LL_ADC_FLAG_ADRDY
             | LL_ADC_FLAG_EOC
             | LL_ADC_FLAG_EOS
             | LL_ADC_FLAG_OVR
             | LL_ADC_FLAG_EOSMP
             | LL_ADC_FLAG_AWD1 )
           );
    
    /* Reset register CR */
    /* Bits ADC_CR_ADCAL, ADC_CR_ADSTP, ADC_CR_ADSTART are in access mode     */
    /* "read-set": no direct reset applicable.                                */
    /* No action on register CR */
    
//.........这里部分代码省略.........

/**
  * @brief  Run the self calibration of the 3 OPAMPs in parallel.
  * @note   Trimming values (PMOS & NMOS) are updated and user trimming is 
  *         enabled is calibration is succesful.
  * @note   Calibration is performed in the mode specified in OPAMP init
  *         structure (mode normal or low-power). To perform calibration for
  *         both modes, repeat this function twice after OPAMP init structure
  *         accordingly updated.
  * @note   Calibration runs about 10 ms (5 dichotmy steps, repeated for P  
  *         and N transistors: 10 steps with 1 ms for each step).
  * @param  hopamp1 handle
  * @param  hopamp2 handle
  * @param  hopamp3 handle
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_OPAMPEx_SelfCalibrateAll(OPAMP_HandleTypeDef *hopamp1, OPAMP_HandleTypeDef *hopamp2, OPAMP_HandleTypeDef *hopamp3)
{
  HAL_StatusTypeDef status = HAL_OK;
  
  uint32_t* opamp1_trimmingvalue = 0;
  uint32_t opamp1_trimmingvaluen = 0;
  uint32_t opamp1_trimmingvaluep = 0;
  
  uint32_t* opamp2_trimmingvalue = 0;
  uint32_t opamp2_trimmingvaluen = 0;
  uint32_t opamp2_trimmingvaluep = 0;
  
  uint32_t* opamp3_trimmingvalue = 0;
  uint32_t opamp3_trimmingvaluen = 0;
  uint32_t opamp3_trimmingvaluep = 0;
  
  uint32_t trimming_diff_pair = 0;          /* Selection of differential transistors pair high or low */

  __IO uint32_t* tmp_opamp1_reg_trimming;   /* Selection of register of trimming depending on power mode: OTR or LPOTR */
  __IO uint32_t* tmp_opamp2_reg_trimming;
  __IO uint32_t* tmp_opamp3_reg_trimming;
  uint32_t tmp_opamp1_otr_otuser = 0;       /* Selection of bit OPAMP_OTR_OT_USER depending on trimming register pointed: OTR or LPOTR */
  uint32_t tmp_opamp2_otr_otuser = 0;
  uint32_t tmp_opamp3_otr_otuser = 0;
  
  uint32_t tmp_Opa1calout_DefaultSate = 0;  /* Bit OPAMP_CSR_OPA1CALOUT default state when trimming value is 00000b. Used to detect the bit toggling */
  uint32_t tmp_Opa2calout_DefaultSate = 0;  /* Bit OPAMP_CSR_OPA2CALOUT default state when trimming value is 00000b. Used to detect the bit toggling */
  uint32_t tmp_Opa3calout_DefaultSate = 0;  /* Bit OPAMP_CSR_OPA3CALOUT default state when trimming value is 00000b. Used to detect the bit toggling */

  uint32_t tmp_OpaxSwitchesContextBackup = 0;
  
  uint8_t trimming_diff_pair_iteration_count = 0;       /* For calibration loop algorithm: to repeat the calibration loop for both differential transistors pair high and low */
  uint8_t delta = 0;                                    /* For calibration loop algorithm: Variable for dichotomy steps value */
  uint8_t final_step_check = 0;                         /* For calibration loop algorithm: Flag for additional check of last trimming step */
  
  /* Check the OPAMP handle allocation */
  /* Check if OPAMP locked */
  if((hopamp1 == NULL) || (hopamp1->State == HAL_OPAMP_STATE_BUSYLOCKED) ||
     (hopamp2 == NULL) || (hopamp2->State == HAL_OPAMP_STATE_BUSYLOCKED) ||
     (hopamp3 == NULL) || (hopamp3->State == HAL_OPAMP_STATE_BUSYLOCKED)   ) 
  {
    status = HAL_ERROR;
  }
  else
  {
  
    /* Check if OPAMP in calibration mode and calibration not yet enable */
    if((hopamp1->State == HAL_OPAMP_STATE_READY) &&
       (hopamp2->State == HAL_OPAMP_STATE_READY) &&
       (hopamp3->State == HAL_OPAMP_STATE_READY)   )
    {
      /* Check the parameter */
      assert_param(IS_OPAMP_ALL_INSTANCE(hopamp1->Instance));
      assert_param(IS_OPAMP_ALL_INSTANCE(hopamp2->Instance));
      assert_param(IS_OPAMP_ALL_INSTANCE(hopamp3->Instance));
      assert_param(IS_OPAMP_POWERMODE(hopamp1->Init.PowerMode));
      assert_param(IS_OPAMP_POWERMODE(hopamp2->Init.PowerMode));
      assert_param(IS_OPAMP_POWERMODE(hopamp3->Init.PowerMode));
      
      /* Update OPAMP state */
      hopamp1->State = HAL_OPAMP_STATE_CALIBBUSY;
      hopamp2->State = HAL_OPAMP_STATE_CALIBBUSY;
      hopamp3->State = HAL_OPAMP_STATE_CALIBBUSY;
      
      /* Backup of switches configuration to restore it at the end of the     */
      /* calibration.                                                         */
      tmp_OpaxSwitchesContextBackup = READ_BIT(OPAMP->CSR, OPAMP_CSR_ALL_SWITCHES_ALL_OPAMPS);
      
      /* Open all switches on non-inverting input, inverting input and output */
      /* feedback.                                                            */
      CLEAR_BIT(OPAMP->CSR, OPAMP_CSR_ALL_SWITCHES_ALL_OPAMPS);
      
      /* Set calibration mode to user programmed trimming values */
      SET_BIT(OPAMP->OTR, OPAMP_OTR_OT_USER);
      
      /* Select trimming settings depending on power mode */
      if (hopamp1->Init.PowerMode == OPAMP_POWERMODE_NORMAL)
      {
        tmp_opamp1_otr_otuser = OPAMP_OTR_OT_USER;
        tmp_opamp1_reg_trimming = &OPAMP->OTR;
      }
      else
      {
        tmp_opamp1_otr_otuser = 0x00000000;
        tmp_opamp1_reg_trimming = &OPAMP->LPOTR;
//.........这里部分代码省略.........

/**
  * @brief  Initializes the OPAMP according to the specified
  *         parameters in the OPAMP_InitTypeDef and initialize the associated handle.
  * @note   If the selected opamp is locked, initialization can't be performed.
  *         To unlock the configuration, perform a system reset.
  * @param  hopamp: OPAMP handle
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_OPAMP_Init(OPAMP_HandleTypeDef *hopamp)
{ 
  HAL_StatusTypeDef status = HAL_OK;
  uint32_t updateotrlpotr = 0;

  /* Check the OPAMP handle allocation and lock status */
  /* Init not allowed if calibration is ongoing */
  if((hopamp == NULL) || (hopamp->State == HAL_OPAMP_STATE_BUSYLOCKED)
                      || (hopamp->State == HAL_OPAMP_STATE_CALIBBUSY))
  {
    return HAL_ERROR;
  }
  else
  {
    /* Check the parameter */
    assert_param(IS_OPAMP_ALL_INSTANCE(hopamp->Instance));
       
    /* Set OPAMP parameters */
    assert_param(IS_OPAMP_POWER_SUPPLY_RANGE(hopamp->Init.PowerSupplyRange));
    assert_param(IS_OPAMP_POWERMODE(hopamp->Init.PowerMode));
    assert_param(IS_OPAMP_FUNCTIONAL_NORMALMODE(hopamp->Init.Mode));
    assert_param(IS_OPAMP_NONINVERTING_INPUT(hopamp->Init.NonInvertingInput));
    
    if ((hopamp->Init.Mode) == OPAMP_STANDALONE_MODE)
    {
      assert_param(IS_OPAMP_INVERTING_INPUT_STANDALONE(hopamp->Init.InvertingInput));
    }

    if ((hopamp->Init.Mode) == OPAMP_PGA_MODE)      
    {
      assert_param(IS_OPAMP_INVERTING_INPUT_PGA(hopamp->Init.InvertingInput));
    }
    
    if ((hopamp->Init.Mode) == OPAMP_PGA_MODE)
    {
      assert_param(IS_OPAMP_PGA_GAIN(hopamp->Init.PgaGain));
    }
    
    assert_param(IS_OPAMP_TRIMMING(hopamp->Init.UserTrimming)); 
    if ((hopamp->Init.UserTrimming) == OPAMP_TRIMMING_USER)
    {
      if (hopamp->Init.PowerMode == OPAMP_POWERMODE_NORMAL)
      {
        assert_param(IS_OPAMP_TRIMMINGVALUE(hopamp->Init.TrimmingValueP));
        assert_param(IS_OPAMP_TRIMMINGVALUE(hopamp->Init.TrimmingValueN));
      }
    else
      {
        assert_param(IS_OPAMP_TRIMMINGVALUE(hopamp->Init.TrimmingValuePLowPower));
        assert_param(IS_OPAMP_TRIMMINGVALUE(hopamp->Init.TrimmingValueNLowPower));
      }
    }
     
    if(hopamp->State == HAL_OPAMP_STATE_RESET)
    {
      /* Allocate lock resource and initialize it */
      hopamp->Lock = HAL_UNLOCKED;
    }

    /* Call MSP init function */
    HAL_OPAMP_MspInit(hopamp);

    /* Set operating mode */
    CLEAR_BIT(hopamp->Instance->CSR, OPAMP_CSR_CALON);
                                              
    if (hopamp->Init.Mode == OPAMP_PGA_MODE)
    {
      MODIFY_REG(hopamp->Instance->CSR, OPAMP_CSR_INIT_MASK_PGA, \
                                        hopamp->Init.PowerMode | \
                                        hopamp->Init.Mode | \
                                        hopamp->Init.PgaGain | \
                                        hopamp->Init.InvertingInput    | \
                                        hopamp->Init.NonInvertingInput | \
                                        hopamp->Init.UserTrimming);
    }
    
    if (hopamp->Init.Mode == OPAMP_FOLLOWER_MODE)
    {
    /* In Follower mode InvertingInput is Not Applicable  */
    MODIFY_REG(hopamp->Instance->CSR, OPAMP_CSR_INIT_MASK_FOLLOWER, \
                                        hopamp->Init.PowerMode | \
                                        hopamp->Init.Mode | \
                                        hopamp->Init.NonInvertingInput | \
                                        hopamp->Init.UserTrimming);     
    }     
    
    if (hopamp->Init.Mode == OPAMP_STANDALONE_MODE)
    {
      MODIFY_REG(hopamp->Instance->CSR, OPAMP_CSR_INIT_MASK_STANDALONE, \
                                        hopamp->Init.PowerMode | \
                                        hopamp->Init.Mode | \
                                        hopamp->Init.InvertingInput    | \
//.........这里部分代码省略.........

/**
  * @brief Enable FIREWALL. 
  * @note Firewall is enabled in clearing FWDIS bit of SYSCFG CFGR1 register.
  *       Once enabled, the Firewall cannot be disabled by software. Only a 
  *       system reset can set again FWDIS bit.           
  * @retval None
  */
void HAL_FIREWALL_EnableFirewall(void)
{
  /* Clears FWDIS bit of SYSCFG CFGR1 register */
  CLEAR_BIT(SYSCFG->CFGR2, SYSCFG_CFGR2_FWDISEN);
  
}

void SSE::remove(docid_t docName, double& duration){
//	docName = "/Users/naveed/BStore/datasets/testdir/" + docName + ".";
	double diskTime = 0;
	clock_t startTime = clock();
	uint64_t docHash = getDocNameHash(boost::lexical_cast<string>(docName));
	uint64_t docID0 = docHash;	CLEAR_BIT(docID0, 0);
	uint64_t docID1 = docHash;	SET_BIT(docID1, 0);

	duration += (double)(clock()-startTime)/(double)CLOCKS_PER_SEC;

	OnlineSession session;
	session.resetDiskAccessTime();

	clock_t ignoredStartTime = clock();
	if(fstore.isFilePresent(boost::lexical_cast<string>(docID0))){
		fstore.remove(boost::lexical_cast<string>(docID0));
//		duration -= (double)(clock()-ignoredStartTime)/(double)CLOCKS_PER_SEC;
		/* Entries from Index will be delete using lazy delete*/
	}
	else if (fstore.isFilePresent(boost::lexical_cast<string>(docID1))){
//	else if (fstore.isFilePresent(boost::lexical_cast<string>(docID))){
		byte* doc;
		double SKETime = 0;
//		size_t size = fstore.get("/Users/naveed/BStore/datasets/test4MB/allen-p/straw/8.", doc, SKETime);
		size_t size = fstore.get(boost::lexical_cast<string>(docID1), doc, SKETime);
		cout << "SKE took " << SKETime << " seconds." << endl;

		unordered_set<string, stringhash> keywords;
		getKeywords(doc, size, keywords);

		duration -= (double)(clock()-ignoredStartTime)/(double)CLOCKS_PER_SEC;
		
		for(unordered_set<string, stringhash>::iterator it = keywords.begin(); it != keywords.end(); ++it){
			string keyword = boost::lexical_cast<string>(1) + *it;
			OnlineSession session;
			byte* docIDs = NULL;
			size_t size = session.updateRead(keyword, docIDs, -sizeof(docid_t), diskTime);
//			cout << "Updating keyword " << keyword << endl;
//			cout << "Number of files containing keyword \"" << keyword << "\" are " << size << endl << " " << size - sizeof(docid_t) << endl;
//			uint32_t docIDtoRemove = findDocID(docIDs, size, docID1);
			uint32_t docIDtoRemove = findDocID(docIDs, size, docName);
			if(docIDtoRemove == -1){
				std::cerr << "File present in filestore but is not present in BStore." << endl;
				std::cerr << "This is probably due to the files stored from previoius runs. Try again after deleting files from previous runs." << endl;
				exit(1);
			}
			deleteDocID(docIDs, size, docIDtoRemove);
//			cout << "DocID to remove " << docIDtoRemove << endl;
			session.updateWrite(keyword, docIDs, size, diskTime);
			delete[] docIDs;
			docIDs = NULL;
		}
	
		delete[] doc;

		duration += (double)(clock()-startTime)/(double)CLOCKS_PER_SEC - diskTime;

		cout << "Disk operations took " << session.getDiskAccessTime() << " seconds." << endl;
		fstore.remove(boost::lexical_cast<string>(docID1));

	}
	else{
		cout << "File not found!" << endl;
	}
	// TODO: delete docNameHash(document) from DocumentStore
}

/**
  * @brief  De-initialize the DMA registers to their default reset values.
  * @param  DMAx DMAx Instance
  * @param  Channel This parameter can be one of the following values:
  *         @arg @ref LL_DMA_CHANNEL_1
  *         @arg @ref LL_DMA_CHANNEL_2
  *         @arg @ref LL_DMA_CHANNEL_3
  *         @arg @ref LL_DMA_CHANNEL_4
  *         @arg @ref LL_DMA_CHANNEL_5
  *         @arg @ref LL_DMA_CHANNEL_6
  *         @arg @ref LL_DMA_CHANNEL_7
  *         @arg @ref LL_DMA_CHANNEL_ALL
  * @retval An ErrorStatus enumeration value:
  *          - SUCCESS: DMA registers are de-initialized
  *          - ERROR: DMA registers are not de-initialized
  */
uint32_t LL_DMA_DeInit(DMA_TypeDef *DMAx, uint32_t Channel)
{
  DMA_Channel_TypeDef *tmp = (DMA_Channel_TypeDef *)DMA1_Channel1;
  ErrorStatus status = SUCCESS;

  /* Check the DMA Instance DMAx and Channel parameters*/
  assert_param(IS_LL_DMA_ALL_CHANNEL_INSTANCE(DMAx, Channel) || (Channel == LL_DMA_CHANNEL_ALL));

  if (Channel == LL_DMA_CHANNEL_ALL)
  {
    if (DMAx == DMA1)
    {
      /* Force reset of DMA clock */
      LL_AHB1_GRP1_ForceReset(LL_AHB1_GRP1_PERIPH_DMA1);

      /* Release reset of DMA clock */
      LL_AHB1_GRP1_ReleaseReset(LL_AHB1_GRP1_PERIPH_DMA1);
    }
#if defined(DMA2)
    else if (DMAx == DMA2)
    {
      /* Force reset of DMA clock */
      LL_AHB1_GRP1_ForceReset(LL_AHB1_GRP1_PERIPH_DMA2);

      /* Release reset of DMA clock */
      LL_AHB1_GRP1_ReleaseReset(LL_AHB1_GRP1_PERIPH_DMA2);
    }
#endif
    else
    {
      status = ERROR;
    }
  }
  else
  {
    tmp = (DMA_Channel_TypeDef *)(__LL_DMA_GET_CHANNEL_INSTANCE(DMAx, Channel));

    /* Disable the selected DMAx_Channely */
    CLEAR_BIT(tmp->CCR, DMA_CCR_EN);

    /* Reset DMAx_Channely control register */
    LL_DMA_WriteReg(tmp, CCR, 0U);

    /* Reset DMAx_Channely remaining bytes register */
    LL_DMA_WriteReg(tmp, CNDTR, 0U);

    /* Reset DMAx_Channely peripheral address register */
    LL_DMA_WriteReg(tmp, CPAR, 0U);

    /* Reset DMAx_Channely memory address register */
    LL_DMA_WriteReg(tmp, CMAR, 0U);

    /* Reset Request register field for DMAx Channel */
    LL_DMA_SetPeriphRequest(DMAx, Channel, LL_DMA_REQUEST_0);

    if (Channel == LL_DMA_CHANNEL_1)
    {
      /* Reset interrupt pending bits for DMAx Channel1 */
      LL_DMA_ClearFlag_GI1(DMAx);
    }
    else if (Channel == LL_DMA_CHANNEL_2)
    {
      /* Reset interrupt pending bits for DMAx Channel2 */
      LL_DMA_ClearFlag_GI2(DMAx);
    }
    else if (Channel == LL_DMA_CHANNEL_3)
    {
      /* Reset interrupt pending bits for DMAx Channel3 */
      LL_DMA_ClearFlag_GI3(DMAx);
    }
    else if (Channel == LL_DMA_CHANNEL_4)
    {
      /* Reset interrupt pending bits for DMAx Channel4 */
      LL_DMA_ClearFlag_GI4(DMAx);
    }
    else if (Channel == LL_DMA_CHANNEL_5)
    {
      /* Reset interrupt pending bits for DMAx Channel5 */
      LL_DMA_ClearFlag_GI5(DMAx);
    }

    else if (Channel == LL_DMA_CHANNEL_6)
    {
      /* Reset interrupt pending bits for DMAx Channel6 */
//.........这里部分代码省略.........

/* Register an event handler and unmask the port */
void register_event(evtchn_port_t port, evtchn_handler_t handler)
{
	handlers[port] = handler;
	CLEAR_BIT(shared_info.evtchn_mask, port);
}

/**
  * @brief  Disables the Clock Security System.
  * @retval None
  */
void HAL_RCC_DisableCSS(void)
{
  CLEAR_BIT(RCC->CR, RCC_CR_CSSON);
}

/**
  * @brief  Initializes the SmartCard mode according to the specified
  *         parameters in the SMARTCARD_HandleTypeDef and create the associated handle.
  * @param  hsc: Pointer to a SMARTCARD_HandleTypeDef structure that contains
  *              the configuration information for the specified SMARTCARD module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SMARTCARD_Init(SMARTCARD_HandleTypeDef *hsc)
{
  /* Check the SMARTCARD handle allocation */
  if(hsc == NULL)
  {
    return HAL_ERROR;
  }

  /* Check Wordlength, Parity and Stop bits parameters */
  if (  (!(IS_SMARTCARD_WORD_LENGTH(hsc->Init.WordLength)))
      ||(!(IS_SMARTCARD_STOPBITS(hsc->Init.StopBits)))
      ||(!(IS_SMARTCARD_PARITY(hsc->Init.Parity)))  )
  {
    return HAL_ERROR;
  }

  /* Check the parameters */
  assert_param(IS_SMARTCARD_INSTANCE(hsc->Instance));
  assert_param(IS_SMARTCARD_NACK_STATE(hsc->Init.NACKState));
  assert_param(IS_SMARTCARD_PRESCALER(hsc->Init.Prescaler));

  if(hsc->State == HAL_SMARTCARD_STATE_RESET)
  {  
    /* Allocate lock resource and initialize it */
    hsc->Lock = HAL_UNLOCKED;
    
    /* Init the low level hardware */
    HAL_SMARTCARD_MspInit(hsc);
  }
  
  hsc->State = HAL_SMARTCARD_STATE_BUSY;

  /* Disable the Peripheral */
  __HAL_SMARTCARD_DISABLE(hsc);
  
  /* Set the Prescaler */
  MODIFY_REG(hsc->Instance->GTPR, USART_GTPR_PSC, hsc->Init.Prescaler);

  /* Set the Guard Time */
  MODIFY_REG(hsc->Instance->GTPR, USART_GTPR_GT, ((hsc->Init.GuardTime)<<8));

  /* Set the Smartcard Communication parameters */
  SMARTCARD_SetConfig(hsc);

  /* In SmartCard mode, the following bits must be kept cleared: 
  - LINEN bit in the USART_CR2 register
  - HDSEL and IREN bits in the USART_CR3 register.*/
  CLEAR_BIT(hsc->Instance->CR2, USART_CR2_LINEN);
  CLEAR_BIT(hsc->Instance->CR3, (USART_CR3_IREN | USART_CR3_HDSEL));

  /* Enable the Peripharal */
  __HAL_SMARTCARD_ENABLE(hsc);

  /* Configure the Smartcard NACK state */
  MODIFY_REG(hsc->Instance->CR3, USART_CR3_NACK, hsc->Init.NACKState);

  /* Enable the SC mode by setting the SCEN bit in the CR3 register */
  SET_BIT(hsc->Instance->CR3, USART_CR3_SCEN);

  /* Initialize the SMARTCARD state*/
  hsc->ErrorCode = HAL_SMARTCARD_ERROR_NONE;
  hsc->State= HAL_SMARTCARD_STATE_READY;

  return HAL_OK;
}

//.........这里部分代码省略.........
    if(pFlash.ProcedureOnGoing == FLASH_PROC_SECTERASE)
    {
      /*return the faulty sector*/
      addresstmp = pFlash.Sector;
      pFlash.Sector = 0xFFFFFFFF;
    }
    else if(pFlash.ProcedureOnGoing == FLASH_PROC_MASSERASE)
    {
      /*return the faulty bank*/
      addresstmp = pFlash.Bank;
    }
    else
    {
      /*return the faulty address*/
      addresstmp = pFlash.Address;
    }
    
    /*Save the Error code*/
    FLASH_SetErrorCode();
    
    /* FLASH error interrupt user callback */
    HAL_FLASH_OperationErrorCallback(addresstmp);
    
    /*Stop the procedure ongoing*/
    pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
  }
  
  /* Check FLASH End of Operation flag  */
  if(__HAL_FLASH_GET_FLAG(FLASH_FLAG_EOP) != RESET)
  {
    /* Clear FLASH End of Operation pending bit */
    __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP);
    
    if(pFlash.ProcedureOnGoing == FLASH_PROC_SECTERASE)
    {
      /*Nb of sector to erased can be decreased*/
      pFlash.NbSectorsToErase--;
      
      /* Check if there are still sectors to erase*/
      if(pFlash.NbSectorsToErase != 0)
      {
        addresstmp = pFlash.Sector;
        /*Indicate user which sector has been erased*/
        HAL_FLASH_EndOfOperationCallback(addresstmp);
        
        /*Increment sector number*/
        pFlash.Sector++;
        addresstmp = pFlash.Sector;
        FLASH_Erase_Sector(addresstmp, pFlash.VoltageForErase);
      }
      else
      {
        /*No more sectors to Erase, user callback can be called.*/
        /*Reset Sector and stop Erase sectors procedure*/
        pFlash.Sector = addresstmp = 0xFFFFFFFF;
        pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
        
        /* Flush the caches to be sure of the data consistency */
        FLASH_FlushCaches() ;
                
        /* FLASH EOP interrupt user callback */
        HAL_FLASH_EndOfOperationCallback(addresstmp);
      }
    }
    else 
    {
      if(pFlash.ProcedureOnGoing == FLASH_PROC_MASSERASE) 
      {
        /* MassErase ended. Return the selected bank */
        /* Flush the caches to be sure of the data consistency */
        FLASH_FlushCaches() ;

        /* FLASH EOP interrupt user callback */
        HAL_FLASH_EndOfOperationCallback(pFlash.Bank);
      }
      else
      {
        /*Program ended. Return the selected address*/
        /* FLASH EOP interrupt user callback */
        HAL_FLASH_EndOfOperationCallback(pFlash.Address);
      }
      pFlash.ProcedureOnGoing = FLASH_PROC_NONE;
    }
  }
  
  if(pFlash.ProcedureOnGoing == FLASH_PROC_NONE)
  {
    /* Operation is completed, disable the PG, SER, SNB and MER Bits */
    CLEAR_BIT(FLASH->CR, (FLASH_CR_PG | FLASH_CR_SER | FLASH_CR_SNB | FLASH_MER_BIT));

    /* Disable End of FLASH Operation interrupt */
    __HAL_FLASH_DISABLE_IT(FLASH_IT_EOP);
    
    /* Disable Error source interrupt */
    __HAL_FLASH_DISABLE_IT(FLASH_IT_ERR);
    
    /* Process Unlocked */
    __HAL_UNLOCK(&pFlash);
  }
}

/**
  * @brief Disable SRAM2 content retention in Standby mode.
  * @note  When RRS bit is reset, SRAM2 is powered off in Standby mode 
  *        and its content is lost.      
  * @retval None
  */
void HAL_PWREx_DisableSRAM2ContentRetention(void)
{
  CLEAR_BIT(PWR->CR3, PWR_CR3_RRS);
}

//.........这里部分代码省略.........
        MODIFY_REG(hopamp2->Instance->CSR, OPAMP_CSR_TRIMOFFSETP, trimmingvaluep2<<OPAMP_INPUT_NONINVERTING);
               
        /* OFFTRIMmax delay 2 ms as per datasheet (electrical characteristics */ 
        /* Offset trim time: during calibration, minimum time needed between */
        /* two steps to have 1 mV accuracy */
        HAL_Delay(2U);

        if (hopamp1->Instance->CSR & OPAMP_CSR_OUTCAL) 
        { 
          /* OPAMP_CSR_OUTCAL is HIGH try higher trimming */
          trimmingvaluep1 += delta;
        }
        else
        {
          trimmingvaluep1 -= delta;
        }
         
        if (hopamp2->Instance->CSR & OPAMP_CSR_OUTCAL) 
        { 
          /* OPAMP_CSR_OUTCAL is HIGH try higher trimming */
          trimmingvaluep2 += delta;
        }
        else
        {
          trimmingvaluep2 -= delta;
        }
                      
        delta >>= 1U;
      }
      
      // Still need to check if righ calibration is current value or un step below
      // Indeed the first value that causes the OUTCAL bit to change from 1 to 0 
      /* Set candidate trimming */
      MODIFY_REG(hopamp1->Instance->CSR, OPAMP_CSR_TRIMOFFSETP, trimmingvaluep1<<OPAMP_INPUT_NONINVERTING);
      MODIFY_REG(hopamp2->Instance->CSR, OPAMP_CSR_TRIMOFFSETP, trimmingvaluep2<<OPAMP_INPUT_NONINVERTING);

       /* OFFTRIMmax delay 2 ms as per datasheet (electrical characteristics */ 
       /* Offset trim time: during calibration, minimum time needed between */
       /* two steps to have 1 mV accuracy */
       HAL_Delay(2U);
      
      if (hopamp1->Instance->CSR & OPAMP_CSR_OUTCAL) 
        { 
          /* OPAMP_CSR_OUTCAL is actually one value more */
          trimmingvaluep1++;
          /* Set right trimming */
          MODIFY_REG(hopamp1->Instance->CSR, OPAMP_CSR_TRIMOFFSETP, trimmingvaluep1<<OPAMP_INPUT_NONINVERTING);
        }
    
      if (hopamp2->Instance->CSR & OPAMP_CSR_OUTCAL) 
        { 
          /* OPAMP_CSR_OUTCAL is actually one value more */
          trimmingvaluep2++;
          /* Set right trimming */
          MODIFY_REG(hopamp2->Instance->CSR, OPAMP_CSR_TRIMOFFSETP, trimmingvaluep2<<OPAMP_INPUT_NONINVERTING);
        }

      /* Disable calibration */
      CLEAR_BIT (hopamp1->Instance->CSR, OPAMP_CSR_CALON);
      CLEAR_BIT (hopamp2->Instance->CSR, OPAMP_CSR_CALON);

      /* Disable the OPAMPs */
      CLEAR_BIT (hopamp1->Instance->CSR, OPAMP_CSR_OPAMPxEN);
      CLEAR_BIT (hopamp2->Instance->CSR, OPAMP_CSR_OPAMPxEN);

      /* Set operating mode back */
      CLEAR_BIT(hopamp1->Instance->CSR, OPAMP_CSR_FORCEVP);
      CLEAR_BIT(hopamp2->Instance->CSR, OPAMP_CSR_FORCEVP);
      
      /* Self calibration is successful  */
      /* Store calibration(user timming) results in init structure. */
      /* Select user timming mode */

      /* Write calibration result N */
      hopamp1->Init.TrimmingValueN = trimmingvaluen1;
      hopamp2->Init.TrimmingValueN = trimmingvaluen2;
     
      /* Write calibration result P */
      hopamp1->Init.TrimmingValueP = trimmingvaluep1;
      hopamp2->Init.TrimmingValueP = trimmingvaluep2;
            
      /* Calibration */
      hopamp1->Init.UserTrimming = OPAMP_TRIMMING_USER;
      hopamp2->Init.UserTrimming = OPAMP_TRIMMING_USER;
    
      /* Select user timming mode */      
      /* And updated with calibrated settings */
      hopamp1->Init.UserTrimming = OPAMP_TRIMMING_USER;
      hopamp2->Init.UserTrimming = OPAMP_TRIMMING_USER;
      
      MODIFY_REG(hopamp1->Instance->CSR, OPAMP_CSR_TRIMOFFSETN, trimmingvaluen1<<OPAMP_INPUT_INVERTING);
      MODIFY_REG(hopamp2->Instance->CSR, OPAMP_CSR_TRIMOFFSETN, trimmingvaluen2<<OPAMP_INPUT_INVERTING);
     
      MODIFY_REG(hopamp1->Instance->CSR, OPAMP_CSR_TRIMOFFSETP, trimmingvaluep1<<OPAMP_INPUT_NONINVERTING);
      MODIFY_REG(hopamp2->Instance->CSR, OPAMP_CSR_TRIMOFFSETP, trimmingvaluep2<<OPAMP_INPUT_NONINVERTING);      
          
    }
    
    else
    {