C++ BSP_LED_Off函数代码示例

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{

  /* STM32F4xx HAL library initialization:
       - Configure the Flash prefetch, instruction and Data caches
       - Configure the Systick to generate an interrupt each 1 msec
       - Set NVIC Group Priority to 4
       - Global MSP (MCU Support Package) initialization
     */
  HAL_Init();

  /* Configure LED3 and LED4 */
  BSP_LED_Init(LED3);
  BSP_LED_Init(LED4);
  
  /* Configure the system clock to 180 MHz */
  SystemClock_Config();

  /*##-1- Configure the UART peripheral ######################################*/
  /* Put the USART peripheral in the Asynchronous mode (UART Mode) */
  /* UART1 configured as follow:
      - Word Length = 8 Bits
      - Stop Bit = One Stop bit
      - Parity = None
      - BaudRate = 9600 baud
      - Hardware flow control disabled (RTS and CTS signals) */
  UartHandle.Instance          = USARTx;
  
  UartHandle.Init.BaudRate     = 9600;
  UartHandle.Init.WordLength   = UART_WORDLENGTH_8B;
  UartHandle.Init.StopBits     = UART_STOPBITS_1;
  UartHandle.Init.Parity       = UART_PARITY_NONE;
  UartHandle.Init.HwFlowCtl    = UART_HWCONTROL_NONE;
  UartHandle.Init.Mode         = UART_MODE_TX_RX;
  UartHandle.Init.OverSampling = UART_OVERSAMPLING_16;
    
  if(HAL_UART_Init(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }
  
#ifdef TRANSMITTER_BOARD

  /* Configure USER Button */
  BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
  /* Wait for USER Button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) == RESET)
  {
  }
  
  /* The board sends the message and expects to receive it back */
  
  /*##-2- Start the transmission process #####################################*/  
  /* While the UART in reception process, user can transmit data through 
     "aTxBuffer" buffer */
  if(HAL_UART_Transmit_DMA(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
  {
    Error_Handler();
  }
  
  /*##-3- Wait for the end of the transfer ###################################*/  
  while (UartReady != SET)
  {
  }
  
  /* Reset transmission flag */
  UartReady = RESET;

  /* Turn LED3 Off */
  BSP_LED_Off(LED3);
  
  /*##-4- Put UART peripheral in reception process ###########################*/  
  if(HAL_UART_Receive_DMA(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
  {
    Error_Handler();
  }

#else
  
  /* The board receives the message and sends it back */

  /*##-2- Put UART peripheral in reception process ###########################*/  
  if(HAL_UART_Receive_DMA(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
  {
    Error_Handler();
  }
  
  /*##-3- Wait for the end of the transfer ###################################*/  
  while (UartReady != SET)
  {
  }

  /* Reset transmission flag */
  UartReady = RESET;
  
//.........这里部分代码省略.........

/**
  * @brief  Main program.
  * @param  None
  * @retval None
  */
int main(void)
{
  /* Enable the CPU Cache */
  CPU_CACHE_Enable();
	
  /* STM32F7xx HAL library initialization:
       - Configure the Flash ART accelerator on ITCM interface
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Set NVIC Group Priority to 4
       - Low Level Initialization
     */
  HAL_Init();

  /* Configure the system clock to 216 MHz */
  SystemClock_Config();
  HAL_Delay(1);

  /* Configure LED1, LED2, LED3 and Tamper push-button */
  BSP_LED_Init(LED1);
  BSP_LED_Init(LED2);
  BSP_LED_Init(LED3);
  BSP_PB_Init(BUTTON_TAMPER, BUTTON_MODE_EXTI);


  /*##-1- Check if the system has resumed from IWDG reset ####################*/
  if (__HAL_RCC_GET_FLAG(RCC_FLAG_IWDGRST) != RESET)
  {
    /* IWDGRST flag set: Turn LED1 on */
    BSP_LED_On(LED1);

    /* Clear reset flags */
    __HAL_RCC_CLEAR_RESET_FLAGS();
  }
  else
  {
    /* IWDGRST flag is not set: Turn LED1 off */
    BSP_LED_Off(LED1);
  }

  /*##-2- Get the LSI frequency: TIM5 is used to measure the LSI frequency ###*/
  uwLsiFreq = GetLSIFrequency();

  /*##-3- Configure the IWDG peripheral ######################################*/
  /* Set counter reload value to obtain 250ms IWDG TimeOut.
     IWDG counter clock Frequency = LsiFreq / 32
     Counter Reload Value = 250ms / IWDG counter clock period
                          = 0.25s / (32/LsiFreq)
                          = LsiFreq / (32 * 4)
                          = LsiFreq / 128 */
  IwdgHandle.Instance = IWDG;

  IwdgHandle.Init.Prescaler = IWDG_PRESCALER_32;
  IwdgHandle.Init.Reload    = uwLsiFreq / 128;
  IwdgHandle.Init.Window    = IWDG_WINDOW_DISABLE;

  if (HAL_IWDG_Init(&IwdgHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }

  /*##-4- Start the IWDG #####################################################*/
  if (HAL_IWDG_Start(&IwdgHandle) != HAL_OK)
  {
    Error_Handler();
  }

  /* Infinite loop */
  while (1)
  {
    /* Toggle LED2 */
    BSP_LED_Toggle(LED2);

    /* Insert 240 ms delay */
    HAL_Delay(240);

    /* Refresh IWDG: reload counter */
    if (HAL_IWDG_Refresh(&IwdgHandle) != HAL_OK)
    {
      /* Refresh Error */
      Error_Handler();
    }
  }
}

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F4xx HAL library initialization:
       - Configure the Flash prefetch, instruction and Data caches
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Set NVIC Group Priority to 4
       - Low Level Initialization: global MSP (MCU Support Package) initialization
     */
  HAL_Init();

  /* Configure the system clock to 100 MHz */
  SystemClock_Config();
  
  /* Configure LED2 */
  BSP_LED_Init(LED2);

  /*##-1- Configure the UART peripheral ######################################*/
  /* Put the USART peripheral in the Asynchronous mode (UART Mode) */
  /* UART configured as follows:
      - Word Length = 8 Bits
      - Stop Bit = One Stop bit
      - Parity = None
      - BaudRate = 9600 baud
      - Hardware flow control disabled (RTS and CTS signals) */
  UartHandle.Instance        = USARTx;

  UartHandle.Init.BaudRate   = 9600;
  UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
  UartHandle.Init.StopBits   = UART_STOPBITS_1;
  UartHandle.Init.Parity     = UART_PARITY_NONE;
  UartHandle.Init.HwFlowCtl  = UART_HWCONTROL_NONE;
  UartHandle.Init.Mode       = UART_MODE_TX_RX;
  if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }  
  if(HAL_UART_Init(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }
  
#ifdef TRANSMITTER_BOARD

  /* Configure User push-button in Interrupt mode */
  BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_EXTI);
  
  /* Wait for User push-button press before starting the Communication.
     In the meantime, LED2 is blinking */
  while(UserButtonStatus == 0)
  {
      /* Toggle LED2*/
      BSP_LED_Toggle(LED2); 
      HAL_Delay(100);
  }
  
  BSP_LED_Off(LED2); 

  
  /* The board sends the message and expects to receive it back */
  
  /*##-2- Start the transmission process #####################################*/  
  /* While the UART in reception process, user can transmit data through 
     "aTxBuffer" buffer */
  if(HAL_UART_Transmit_DMA(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
  {
    Error_Handler();
  }
  
  /*##-3- Wait for the end of the transfer ###################################*/  
  while (UartReady != SET)
  {
  }

  
  /* Reset transmission flag */
  UartReady = RESET;
  
  /*##-4- Put UART peripheral in reception process ###########################*/ 
  if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }  
  if(HAL_UART_Init(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }   
  if(HAL_UART_Receive_DMA(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
  {
    Error_Handler();
  }

//.........这里部分代码省略.........

/**
  * @brief  Main program.
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F0xx HAL library initialization:
       - Configure the Flash prefetch
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Low Level Initialization
     */
  HAL_Init();
  
  /* Configure the system clock to 48 MHz */
  SystemClock_Config();
  
  
  /*## Configure peripherals #################################################*/
  
  /* Initialize LED on board */
  BSP_LED_Init(LED2);
  
  /* Configure User push-button in Interrupt mode */
  BSP_PB_Init(BUTTON_USER, BUTTON_MODE_EXTI);
  
  /* Configure the ADCx peripheral */
  ADC_Config();
  
  /* Run the ADC calibration */
  if (HAL_ADCEx_Calibration_Start(&AdcHandle) != HAL_OK)
  {
    /* Calibration Error */
    Error_Handler();
  }

#if defined(ADC_TRIGGER_FROM_TIMER)
  /* Configure the TIM peripheral */
  TIM_Config();
#endif /* ADC_TRIGGER_FROM_TIMER */

#if defined(WAVEFORM_VOLTAGE_GENERATION_FOR_TEST)
  /* Configure the DAC peripheral and generate a constant voltage of Vdda/2.  */
  WaveformVoltageGenerationForTest_Config();
#endif /* WAVEFORM_VOLTAGE_GENERATION_FOR_TEST */
  
  
  /*## Enable peripherals ####################################################*/
  
#if defined(ADC_TRIGGER_FROM_TIMER)
  /* Timer enable */
  if (HAL_TIM_Base_Start(&TimHandle) != HAL_OK)
  {
    /* Counter Enable Error */
    Error_Handler();
  }
#endif /* ADC_TRIGGER_FROM_TIMER */
  
  
  /*## Start ADC conversions #################################################*/
  
  /* Start ADC conversion on regular group with transfer by DMA */
  if (HAL_ADC_Start_DMA(&AdcHandle,
                        (uint32_t *)aADCxConvertedValues,
                        ADCCONVERTEDVALUES_BUFFER_SIZE
                       ) != HAL_OK)
  {
    /* Start Error */
    Error_Handler();
  }
  
  
  /* Infinite loop */
  while (1)
  {
  
    /* Turn-on/off LED2 in function of ADC conversion result */
    /* - Turn-off if voltage is into AWD window */
    /* - Turn-on if voltage is out of AWD window */

    /* Variable of analog watchdog status is set into analog watchdog         */
    /* interrupt callback                                                     */
    if (ubAnalogWatchdogStatus == RESET)
    {
      BSP_LED_Off(LED2);
    }
    else
    {
      BSP_LED_On(LED2);
      
      /* Reset analog watchdog status for next loop iteration */
      ubAnalogWatchdogStatus = RESET;
    }
  
    /* For information: ADC conversion results are stored into array          */
    /* "aADCxConvertedValues" (for debug: check into watch window)            */
//.........这里部分代码省略.........

/**
  * @brief  IAP Read all flash memory.
  * @param  None
  * @retval None
  */
void COMMAND_Upload(void)
{
  __IO uint32_t address = APPLICATION_ADDRESS;
  __IO uint32_t counterread = 0x00;
  uint32_t tmpcounter = 0x00, indexoffset = 0x00;
  FlagStatus readoutstatus = SET;
  uint16_t byteswritten;
  
  /* Get the read out protection status */
  readoutstatus = FLASH_If_ReadOutProtectionStatus();
  if(readoutstatus == RESET)
  {
    /* Remove UPLOAD file if it exists on flash disk */
    f_unlink(UPLOAD_FILENAME);
    
    /* Init written byte counter */
    indexoffset = (APPLICATION_ADDRESS - USER_FLASH_STARTADDRESS);
    
    /* Open binary file to write on it */
    if(( Appli_state == APPLICATION_READY) && (f_open(&MyFile, UPLOAD_FILENAME, FA_CREATE_ALWAYS | FA_WRITE) == FR_OK))
    {
      /* Upload On Going: Turn LED4 On and LED3 Off */
      BSP_LED_On(LED4); 
      BSP_LED_Off(LED3);
      
      /* Read flash memory */
      while ((indexoffset < USER_FLASH_SIZE) && ( Appli_state == APPLICATION_READY))
      {
        for(counterread = 0; counterread < BUFFER_SIZE; counterread++)
        {
          /* Check the read bytes versus the end of flash */
          if(indexoffset + counterread < USER_FLASH_SIZE)
          {
            tmpcounter = counterread;
            RAM_Buf[tmpcounter] = (*(uint8_t*)(address++));
          }
          /* In this case all flash was read */
          else
          {
            break;
          }
        }
        
        /* Write buffer to file */
        f_write (&MyFile, RAM_Buf, BUFFER_SIZE, (void *)&byteswritten);
        
        /* Number of byte written  */
        indexoffset = indexoffset + counterread;
      }
      
      /* Turn LED1 On: Upload Done */
      BSP_LED_Off(LED4);
      BSP_LED_Off(LED2); 
      BSP_LED_On(LED1); 
      
      /* Close file and filesystem */
      f_close(&MyFile);
      f_mount(0, 0, 0);   
    }
    /* Keep These LEDS OFF when Device connected */
    BSP_LED_Off(LED2); 
    BSP_LED_Off(LED3);
  }
  else
  {
    /* Message ROP active: Turn LED2 On and Toggle LED3 in infinite loop */
    BSP_LED_On(LED2);
    Fail_Handler();
  }
}

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{

  /* STM32F3xx HAL library initialization:
       - Configure the Flash prefetch
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Set NVIC Group Priority to 4
       - Low Level Initialization
     */
  HAL_Init();
  
  /* LED Configuration */
  BSP_LED_Init(LED3);
  BSP_LED_Init(LED6);
  BSP_LED_Init(LED4);
  BSP_LED_Init(LED5);


  /* Configure the system clock to 168 Mhz */
  SystemClock_Config();

  /*##-1- Configure the UART peripheral ######################################*/
  /* Put the USART peripheral in the Asynchronous mode (UART Mode) */
  /* UART configured as follows:
      - Word Length = 8 Bits
      - Stop Bit = One Stop bit
      - Parity = None
      - BaudRate = 9600 baud
      - Hardware flow control disabled (RTS and CTS signals) */
  UartHandle.Instance        = USARTx;

  UartHandle.Init.BaudRate   = 9600;
  UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
  UartHandle.Init.StopBits   = UART_STOPBITS_1;
  UartHandle.Init.Parity     = UART_PARITY_NONE;
  UartHandle.Init.HwFlowCtl  = UART_HWCONTROL_NONE;
  UartHandle.Init.Mode       = UART_MODE_TX_RX;
  UartHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
  if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }  
  if(HAL_UART_Init(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }
  
#ifdef TRANSMITTER_BOARD

  /* Configure User push-button in Interrupt mode */
  BSP_PB_Init(BUTTON_USER, BUTTON_MODE_EXTI);
  
  /* Wait for User push-button press before starting the Communication.
     In the meantime, LED6 is blinking */
  while(UserButtonStatus == 0)
  {
      /* Toggle LED6*/
      BSP_LED_Toggle(LED6); 
      HAL_Delay(100);
  }
  
  BSP_LED_Off(LED6); 
  
  
  /* The board sends the message and expects to receive it back */
  
  /*##-2- Start the transmission process #####################################*/  
  /* While the UART in reception process, user can transmit data through 
     "aTxBuffer" buffer */
  if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE, 5000)!= HAL_OK)
  {
    Error_Handler();   
  }
  
  /* Turn LED5 on: Transfer in transmission process is correct */
  BSP_LED_On(LED5);
  
  /*##-3- Put UART peripheral in reception process ###########################*/  
  if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 5000) != HAL_OK)
  {
    Error_Handler();  
  }
   
  /* Turn LED4 on: Transfer in reception process is correct */
  BSP_LED_On(LED4);
 
#else
  
  /* The board receives the message and sends it back */

  /*##-2- Put UART peripheral in reception process ###########################*/
//.........这里部分代码省略.........

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{    
  /* STM32F3xx HAL library initialization:
       - Configure the Flash prefetch
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Set NVIC Group Priority to 4
       - Low Level Initialization
     */
  HAL_Init();
  
  /* Configure the system clock to 72 Mhz */
  SystemClock_Config();

  /* Update system core clock value for debug purpose*/
  SystemCoreClockUpdate();  
  
  /* Configure LED3, LED5, LED7 and User Button of F3-DK*/     
  BSP_LED_Init(LED3);
  BSP_LED_Init(LED5);
  BSP_LED_Init(LED7);
  BSP_PB_Init(BUTTON_USER, BUTTON_MODE_EXTI);

  /*##-1- Check if the system has resumed from WWDG reset ####################*/
  if(__HAL_RCC_GET_FLAG(RCC_FLAG_WWDGRST) != RESET)
  { 
    /* WWDGRST flag set: Turn LED5 on */
    BSP_LED_On(LED5);

    /* Clear reset flags */
    __HAL_RCC_CLEAR_RESET_FLAGS();
  }
  else
  {
    /* WWDGRST flag is not set: Turn LED5 off */
    BSP_LED_Off(LED5);
  }
    
  /*##-2- Configure the WWDG peripheral ######################################*/
  /* WWDG clock counter = (PCLK1 (36MHz)/4096)/8) = 1098 Hz (~910 us) 
     WWDG Window value = 80 means that the WWDG counter should be refreshed only 
     when the counter is below 80 (and greater than 64/0x40) otherwise a reset will 
     be generated. 
     WWDG Counter value = 127, WWDG timeout = ~910 us * 64 = 58.24 ms 
     In this case the refresh window is: ~910 * (127-80) = 42.7ms < refresh window < ~910 * 64 = 58.24ms
   */
  WwdgHandle.Instance = WWDG;

  WwdgHandle.Init.Prescaler = WWDG_PRESCALER_8;
  WwdgHandle.Init.Window = 80;
  WwdgHandle.Init.Counter = 127;

  if(HAL_WWDG_Init(&WwdgHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }
  
  /*##-5- Start the WWDG #####################################################*/ 
  if(HAL_WWDG_Start(&WwdgHandle) != HAL_OK)
  {
    Error_Handler();
  }
  
  /* Infinite loop */ 
  while (1)
  {
    /* Toggle LED2 */
    BSP_LED_Toggle(LED7);
    
    /* Insert 43 ms delay */
    HAL_Delay(45);
    
    /* Refresh WWDG: update counter value to 127, the refresh window is: 
    ~910 * (127-80) = 42.7ms < refresh window < ~910 * 64 = 58.24ms */  
    
    if(HAL_WWDG_Refresh(&WwdgHandle, 127) != HAL_OK)
    {
      Error_Handler();
    }
  }
}

/**
  * @brief  Main program.
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F0xx HAL library initialization:
       - Configure the Flash prefetch
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Low Level Initialization
     */
  HAL_Init();

  /* Configure LED2, LED2 and LED2 */
  BSP_LED_Init(LED2);
  /* Configure the system clock to 48 MHz */
  SystemClock_Config();

  /*##-1- Configure the SPI peripheral #######################################*/
  /* Set the SPI parameters */
  SpiHandle.Instance               = SPIx;

  SpiHandle.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_256;
  SpiHandle.Init.Direction         = SPI_DIRECTION_2LINES;
  SpiHandle.Init.CLKPhase          = SPI_PHASE_1EDGE;
  SpiHandle.Init.CLKPolarity       = SPI_POLARITY_LOW;
  SpiHandle.Init.CRCCalculation    = SPI_CRCCALCULATION_DISABLE;
  SpiHandle.Init.CRCPolynomial     = 7;
  SpiHandle.Init.DataSize          = SPI_DATASIZE_8BIT;
  SpiHandle.Init.FirstBit          = SPI_FIRSTBIT_MSB;
  SpiHandle.Init.NSS               = SPI_NSS_SOFT;
  SpiHandle.Init.TIMode            = SPI_TIMODE_DISABLE;
  SpiHandle.Init.NSSPMode          = SPI_NSS_PULSE_DISABLE;
  SpiHandle.Init.CRCLength         = SPI_CRC_LENGTH_8BIT;

#ifdef MASTER_BOARD
  SpiHandle.Init.Mode = SPI_MODE_MASTER;
#else
  SpiHandle.Init.Mode = SPI_MODE_SLAVE;
#endif /* MASTER_BOARD */

  if(HAL_SPI_Init(&SpiHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }

#ifdef MASTER_BOARD
  /* Configure push button */
  BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);
  /* Wait for Button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
  {
    BSP_LED_Toggle(LED2);
    HAL_Delay(100);
  }
  BSP_LED_Off(LED2);
#endif /* MASTER_BOARD */

  /*##-2- Start the Full Duplex Communication process ########################*/  
  /* While the SPI in TransmitReceive process, user can transmit data through 
     "aTxBuffer" buffer & receive data through "aRxBuffer" */
  /* Timeout is set to 5S */
  
  switch(HAL_SPI_TransmitReceive(&SpiHandle, (uint8_t*)aTxBuffer, (uint8_t *)aRxBuffer, BUFFERSIZE, 5000))
  {
    case HAL_OK:
      /* Communication is completed ___________________________________________ */
      /* Compare the sent and received buffers */
      if (Buffercmp((uint8_t *)aTxBuffer, (uint8_t *)aRxBuffer, BUFFERSIZE))
      {
        /* Transfer error in transmission process */
        Error_Handler();
      }
      /* Turn LED2 on: Transfer in transmission/Reception process is correct */
      BSP_LED_On(LED2);
      break;

    case HAL_TIMEOUT:
      /* An Error Occur ______________________________________________________ */
    case HAL_ERROR:
      /* Call Timeout Handler */
      Error_Handler();
      break;
    default:
      break;
  }

  /* Infinite loop */
  while (1)
  {
  }
}

/**
  * @brief  Main program.
  * @param  None
  * @retval None
  */
int main(void)
{
#ifdef MASTER_BOARD
  GPIO_InitTypeDef  GPIO_InitStruct;
#endif

  /* STM32F3xx HAL library initialization:
       - Configure the Flash prefetch
       - Configure the Systick to generate an interrupt each 1 msec
       - Set NVIC Group Priority to 4
       - Low Level Initialization
     */
  HAL_Init();
  
  /* Configure the system clock to 64 MHz */
  SystemClock_Config();

  /* Configure LED3 */
  BSP_LED_Init(LED3);

  /*##-1- Configure the SPI peripheral #######################################*/
  /* Set the SPI parameters */
  SpiHandle.Instance               = SPIx;
  SpiHandle.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_256;
  SpiHandle.Init.Direction         = SPI_DIRECTION_2LINES;
  SpiHandle.Init.CLKPhase          = SPI_PHASE_1EDGE;
  SpiHandle.Init.CLKPolarity       = SPI_POLARITY_LOW;
  SpiHandle.Init.DataSize          = SPI_DATASIZE_8BIT;
  SpiHandle.Init.FirstBit          = SPI_FIRSTBIT_MSB;
  SpiHandle.Init.TIMode            = SPI_TIMODE_DISABLE;
  SpiHandle.Init.CRCCalculation    = SPI_CRCCALCULATION_DISABLE;
  SpiHandle.Init.CRCPolynomial     = 7;
  SpiHandle.Init.CRCLength         = SPI_CRC_LENGTH_8BIT;
  SpiHandle.Init.NSS               = SPI_NSS_SOFT;
  SpiHandle.Init.NSSPMode          = SPI_NSS_PULSE_DISABLE;

#ifdef MASTER_BOARD
  SpiHandle.Init.Mode = SPI_MODE_MASTER;
#else
  SpiHandle.Init.Mode = SPI_MODE_SLAVE;
#endif /* MASTER_BOARD */

  if(HAL_SPI_Init(&SpiHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }

#ifdef MASTER_BOARD

  /* Configure PA.12 (Arduino D2) button */
  GPIO_InitStruct.Pin = GPIO_PIN_12;
  GPIO_InitStruct.Pull = GPIO_PULLUP;
  GPIO_InitStruct.Mode = GPIO_MODE_INPUT; 
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
 
  /* Enable GPIOA clock */
  __HAL_RCC_GPIOA_CLK_ENABLE();

  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

  /* Wait Until PA.12 (Arduino D2) is connected to GND */
  while(HAL_GPIO_ReadPin(GPIOA, GPIO_PIN_12) == GPIO_PIN_SET) 
  {
    BSP_LED_Toggle(LED3);
    HAL_Delay(100);
  }
  BSP_LED_Off(LED3);
#endif /* MASTER_BOARD */

  /*##-2- Start the Full Duplex Communication process ########################*/  
  /* While the SPI in TransmitReceive process, user can transmit data through 
     "aTxBuffer" buffer & receive data through "aRxBuffer" */
  /* Timeout is set to 5S */
  
  switch(HAL_SPI_TransmitReceive(&SpiHandle, (uint8_t*)aTxBuffer, (uint8_t *)aRxBuffer, BUFFERSIZE, 5000))
  {
    case HAL_OK:
      /* Communication is completed ___________________________________________ */
      /* Compare the sent and received buffers */
      if (Buffercmp((uint8_t *)aTxBuffer, (uint8_t *)aRxBuffer, BUFFERSIZE))
      {
        /* Transfer error in transmission process */
        Error_Handler();
      }
      /* Turn LED3 on: Transfer in transmission/Reception process is correct */
      BSP_LED_On(LED3);
      break;

    case HAL_TIMEOUT:
      /* An Error Occur ______________________________________________________ */
    case HAL_ERROR:
      /* Call Timeout Handler */
      Error_Handler();
      break;
//.........这里部分代码省略.........

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* Enable the CPU Cache */
  CPU_CACHE_Enable();
  
  /* STM32F7xx HAL library initialization:
       - Configure the Flash ART accelerator on ITCM interface
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Set NVIC Group Priority to 4
       - Low Level Initialization
     */
  HAL_Init();

  /* Configure the system clock to 216 MHz */
  SystemClock_Config();

  /* Since MFX is used, LED init is done after clock config */
  /* Configure LED1, LED2, LED3 and LED4 */
  BSP_LED_Init(LED1);
  BSP_LED_Init(LED2);
  BSP_LED_Init(LED3);
  BSP_LED_Init(LED4);

  /* Tamper push-button (EXTI15_10) will be used to wakeup the system from STOP mode */
  BSP_PB_Init(BUTTON_TAMPER, BUTTON_MODE_EXTI);

  /*## Configure the RTC peripheral #######################################*/
  /* Enable Power Clock */
  __HAL_RCC_PWR_CLK_ENABLE();

  /* Allow Access to RTC Backup domaine */
  HAL_PWR_EnableBkUpAccess();

  RTCHandle.Instance = RTC;
  /* Configure RTC prescaler and RTC data registers as follows:
  - Hour Format = Format 24
  - Asynch Prediv = Value according to source clock
  - Synch Prediv = Value according to source clock
  - OutPut = Output Disable
  - OutPutPolarity = High Polarity
  - OutPutType = Open Drain */
  RTCHandle.Init.HourFormat = RTC_HOURFORMAT_24;
  RTCHandle.Init.AsynchPrediv = RTC_ASYNCH_PREDIV;
  RTCHandle.Init.SynchPrediv = RTC_SYNCH_PREDIV;
  RTCHandle.Init.OutPut = RTC_OUTPUT_DISABLE;
  RTCHandle.Init.OutPutPolarity = RTC_OUTPUT_POLARITY_HIGH;
  RTCHandle.Init.OutPutType = RTC_OUTPUT_TYPE_OPENDRAIN;
  if (HAL_RTC_Init(&RTCHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }

  while (1)
  {
    /* Turn On LED4 */
    BSP_LED_On(LED4);

    /* Insert 5 second delay */
    HAL_Delay(5000);

    /*## Configure the Wake up timer ###########################################*/
    /*  RTC Wakeup Interrupt Generation:
        Wakeup Time Base = (RTC_WAKEUPCLOCK_RTCCLK_DIV /(LSI))
        Wakeup Time = Wakeup Time Base * WakeUpCounter 
                    = (RTC_WAKEUPCLOCK_RTCCLK_DIV /(LSI)) * WakeUpCounter
        ==> WakeUpCounter = Wakeup Time / Wakeup Time Base
  
        To configure the wake up timer to 4s the WakeUpCounter is set to 0x242B:
          RTC_WAKEUPCLOCK_RTCCLK_DIV = RTCCLK_Div16 = 16 
          Wakeup Time Base = 16 /(~37KHz) = ~0,432 ms
          Wakeup Time = ~4s = 0,432ms  * WakeUpCounter
          ==> WakeUpCounter = ~4s/0,432ms = 9259 = 0x242B */
    HAL_RTCEx_SetWakeUpTimer_IT(&RTCHandle, 0x242B, RTC_WAKEUPCLOCK_RTCCLK_DIV16);

    /* Turn OFF LED's */
    BSP_LED_Off(LED1);
    BSP_LED_Off(LED2);
    BSP_LED_Off(LED4);

#ifdef UNDERDRIVE_MODE
    __HAL_PWR_UNDERDRIVE_ENABLE();
#endif /* UNDERDRIVE_MODE */

    /* Enter Stop Mode */
    HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);

    /* Disable Wakeup Counter */
    HAL_RTCEx_DeactivateWakeUpTimer(&RTCHandle);

    /* Configures system clock after wake-up from STOP: enable HSE, PLL and select
//.........这里部分代码省略.........

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  GPIO_InitTypeDef  GPIO_InitStruct;
  /* STM32L0xx HAL library initialization:
       - Configure the Flash prefetch, Flash preread and Buffer caches
       - Systick timer is configured by default as source of time base, but user 
             can eventually implement his proper time base source (a general purpose 
             timer for example or other time source), keeping in mind that Time base 
             duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
             handled in milliseconds basis.
       - Low Level Initialization
     */
  HAL_Init();

  /* Enable MSI oscillator and configure the PLL to reach the max system frequency (2 MHz)
     when using MSI oscillator as PLL clock source. */
  SystemClock_Config();

  /* Configure LED3 */
  BSP_LED_Init(LED3);

  /* Enable GPIOA clock */
  __HAL_RCC_GPIOA_CLK_ENABLE();
  
  /* Configure PA.12 (Arduino D2) button, will be used to trigger an interrupt each time it's connected.
     In the ISR the PLL source will be changed from different clocks */
  GPIO_InitStruct.Pin = GPIO_PIN_12;
  GPIO_InitStruct.Pull = GPIO_PULLUP;
  GPIO_InitStruct.Mode = GPIO_MODE_IT_FALLING; 
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

  /* Enable and set PA.12 (Arduino D2) button EXTI Interrupt to the lowest priority */
  NVIC_SetPriority((IRQn_Type)(EXTI4_15_IRQn), 0x03);
  HAL_NVIC_EnableIRQ((IRQn_Type)(EXTI4_15_IRQn)); 
  

  /* Output LSI on MCO1 pin(PA.08) */
  HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_LSI, RCC_MCODIV_1);



  /* carry on from here */
  /* LED toggling in an infinite loop */
  while (1)
  {
    /* Toggle LED3 */
     if ((RCC->CSR & RCC_CSR_LSION) !=  RCC_CSR_LSION)
    {
      /* if LSI is off, fast LED3 toggle */
      BSP_LED_Toggle(LED3);
      HAL_Delay(100);
    }
    else
    {
      /* if LSI is on, LED3 is emitting a double flash every half-second */  
      BSP_LED_On(LED3); 
      HAL_Delay(100);
      BSP_LED_Off(LED3); 
      HAL_Delay(100);
      BSP_LED_On(LED3); 
      HAL_Delay(100);
      BSP_LED_Off(LED3); 
      HAL_Delay(500); 
    }      

  }
}

/**
  * @brief  Execute the demo application.
  * @param  None
  * @retval None
  */
static void Demo_Exec(void)
{
  uint8_t togglecounter = 0x00;
  
  /* Initialize Accelerometer MEMS*/
  if(BSP_ACCELERO_Init() != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler(); 
  }

  while(1)
  {
    DemoEnterCondition = 0x00;
    
    /* Reset UserButton_Pressed variable */
    UserButtonPressed = 0x00;
    
    /* Configure LEDs to be managed by GPIO */
    BSP_LED_Init(LED3);
    BSP_LED_Init(LED4);
    BSP_LED_Init(LED5);
    BSP_LED_Init(LED6);
    
    /* SysTick end of count event each 10ms */
    SystemCoreClock = HAL_RCC_GetHCLKFreq();
    SysTick_Config(SystemCoreClock / 100);  
    
    /* Turn OFF all LEDs */
    BSP_LED_Off(LED4);
    BSP_LED_Off(LED3);
    BSP_LED_Off(LED5);
    BSP_LED_Off(LED6);
    
    /* Waiting User Button is pressed */
    while (UserButtonPressed == 0x00)
    {
      /* Toggle LED4 */
      BSP_LED_Toggle(LED4);
      HAL_Delay(10);
      /* Toggle LED4 */
      BSP_LED_Toggle(LED3);
      HAL_Delay(10);
      /* Toggle LED4 */
      BSP_LED_Toggle(LED5);
      HAL_Delay(10);
      /* Toggle LED4 */
      BSP_LED_Toggle(LED6);
      HAL_Delay(10);
      togglecounter ++;
      if (togglecounter == 0x10)
      {
        togglecounter = 0x00;
        while (togglecounter < 0x10)
        {
          BSP_LED_Toggle(LED4);
          BSP_LED_Toggle(LED3);
          BSP_LED_Toggle(LED5);
          BSP_LED_Toggle(LED6);
          HAL_Delay(10);
          togglecounter ++;
        }
        togglecounter = 0x00;
      }
    }
    
    /* Waiting User Button is Released */
    while (BSP_PB_GetState(BUTTON_KEY) != KEY_NOT_PRESSED)
    {}
    UserButtonPressed = 0x00;
    
    /* TIM4 channels configuration */
    TIM4_Config();
  
    DemoEnterCondition = 0x01; 
    
    /* USB configuration */
    Demo_USBConfig();
    
    /* Waiting User Button is pressed */
    while (UserButtonPressed == 0x00)
    {}
    
    /* Waiting User Button is Released */
    while (BSP_PB_GetState(BUTTON_KEY) != KEY_NOT_PRESSED)
    {}
    
    /* Disconnect the USB device */
    USBD_Stop(&hUSBDDevice);
    USBD_DeInit(&hUSBDDevice);
  }
}

/**
  * @brief  Main program.
  * @param  None
  * @retval None
  */
int main(void)
{ 
  tsl_user_status_t tsl_status;

  /* STM32F3xx HAL library initialization:
       - Configure the Flash prefetch
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Set NVIC Group Priority to 4
       - Low Level Initialization
     */
  HAL_Init();

  /* Configure LEDs */
  BSP_LED_Init(LED1);
  BSP_LED_Init(LED2);
  BSP_LED_Init(LED4);
  BSP_LED_Init(LED3);

  /* Configure the system clock to 72 MHz */
  SystemClock_Config();

  /* Configure the TSC peripheral */
  TscHandle.Instance                     = TSCx;
  TscHandle.Init.AcquisitionMode         = TSC_ACQ_MODE_NORMAL;
  TscHandle.Init.CTPulseHighLength       = TSC_CTPH_2CYCLES;
  TscHandle.Init.CTPulseLowLength        = TSC_CTPL_2CYCLES;
  TscHandle.Init.IODefaultMode           = TSC_IODEF_OUT_PP_LOW;
  TscHandle.Init.MaxCountInterrupt       = DISABLE;
  TscHandle.Init.MaxCountValue           = TSC_MCV_8191;
  TscHandle.Init.PulseGeneratorPrescaler = TSC_PG_PRESC_DIV64;
  TscHandle.Init.SpreadSpectrum          = DISABLE;
  TscHandle.Init.SpreadSpectrumDeviation = 127;
  TscHandle.Init.SpreadSpectrumPrescaler = TSC_SS_PRESC_DIV1;
  TscHandle.Init.SynchroPinPolarity      = TSC_SYNC_POLARITY_FALLING;
  /* All channel, shield and sampling IOs must be declared below */
  TscHandle.Init.ChannelIOs              = (TSC_GROUP8_IO2 | TSC_GROUP8_IO4);
  TscHandle.Init.SamplingIOs             = (TSC_GROUP8_IO1 | TSC_GROUP8_IO1 | TSC_GROUP6_IO1);
  TscHandle.Init.ShieldIOs               = TSC_GROUP6_IO2;

  if (HAL_TSC_Init(&TscHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }

  /* Just to indicate the fw is alive... */
  BSP_LED_On(LED1);
  BSP_LED_On(LED2);
  BSP_LED_On(LED4);
  BSP_LED_On(LED3);
  
  /* Configure LCD */
#if USE_LCD > 0
  BSP_LCD_Init();
  BSP_LCD_SetFont(&LCD_DEFAULT_FONT);
  BSP_LCD_SetBackColor(LCD_COLOR_WHITE); 
  BSP_LCD_Clear(LCD_COLOR_WHITE);
  BSP_LCD_SetTextColor(LCD_COLOR_DARKBLUE);
  BSP_LCD_DisplayStringAt(0, 10, (uint8_t *)"STM32F303xE", CENTER_MODE);
  BSP_LCD_DisplayStringAt(0, 35, (uint8_t *)"TouchSensing", CENTER_MODE);
  BSP_LCD_DisplayStringAt(0, 55, (uint8_t *)"Example", CENTER_MODE);
#endif
  
  BSP_LED_Off(LED1);
  BSP_LED_Off(LED2);
  BSP_LED_Off(LED4);
  BSP_LED_Off(LED3);
  
  /* Initialize the STMTouch driver */
  tsl_user_Init();
  
  /* Infinite loop */
  while (1)
  {
    /* Execute STMTouch Driver state machine */
    tsl_status = tsl_user_Exec();
    if (tsl_status != TSL_USER_STATUS_BUSY)
    {
      Process_Sensors(tsl_status);
    }
  }
}

static void BlueNRG_Init()
{
  int rc;
  uint8_t bdaddr[] = {0x12, 0x34, 0x00, 0xE1, 0x80, 0x02};
  uint16_t service_handle, dev_name_char_handle, appearance_char_handle;
  const char *ble_name = "BlueNRG";

  BSP_LED_On(LED3);
  HCI_Init();

  /* Enable and set EXTI for BlueNRG IRQ */
  HAL_NVIC_SetPriority(BLUENRG_IRQ_EXTI_IRQn, 2, 0);
  HAL_NVIC_EnableIRQ(BLUENRG_IRQ_EXTI_IRQn);

  BlueNRG_RST();

  BSP_LED_On(LED4);
  rc = aci_hal_write_config_data(CONFIG_DATA_PUBADDR_OFFSET,
                                 CONFIG_DATA_PUBADDR_LEN, bdaddr);
  while (rc) {
    HAL_Delay(100);
    BSP_LED_Toggle(LED4);
  }

  BSP_LED_On(LED5);
  rc = aci_gatt_init();
  while (rc) {
    HAL_Delay(100);
    BSP_LED_Toggle(LED5);
  }

  BSP_LED_On(LED6);
  rc = aci_gap_init(1, &service_handle, &dev_name_char_handle,
                    &appearance_char_handle);
  while (rc) {
    HAL_Delay(100);
    BSP_LED_Toggle(LED6);
  }

  BSP_LED_Off(LED3);
  rc = aci_gatt_update_char_value(service_handle, dev_name_char_handle,
                                  0, strlen(ble_name), (uint8_t *)ble_name);
  while (rc) {
    HAL_Delay(100);
    BSP_LED_Toggle(LED3);
  }

  BSP_LED_Off(LED4);
  rc = aci_gap_set_auth_requirement(MITM_PROTECTION_REQUIRED,
                                    OOB_AUTH_DATA_ABSENT,
                                    NULL,
                                    7,
                                    16,
                                    USE_FIXED_PIN_FOR_PAIRING,
                                    123456,
                                    BONDING);
  while (rc) {
    HAL_Delay(100);
    BSP_LED_Toggle(LED4);
  }

  /* sensors have been initialized in HW_Init() */

  BSP_LED_Off(LED5);
  rc = Add_Acc_Service();
  while (rc) {
    HAL_Delay(100);
    BSP_LED_Toggle(LED5);
  }

  BSP_LED_Off(LED6);
  rc = Add_Environmental_Sensor_Service();
  while (rc) {
    HAL_Delay(100);
    BSP_LED_Toggle(LED6);
  }

  /* Init_User_Timer();
  Start_User_Timer(); */

  BSP_LED_On(LED3);
  /* -2 dBm output power */
  rc = aci_hal_set_tx_power_level(1, 4);
  while (rc) {
    HAL_Delay(100);
    BSP_LED_Toggle(LED3);
  }
}

int main(void)
{

  /* USER CODE BEGIN 1 */
  trace_printf("Hello\n");
  /* USER CODE END 1 */

  /* MCU Configuration----------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* Configure the system clock */
  SystemClock_Config();

  /* Initialize all configured peripherals */
  MX_GPIO_Init();

  /* USER CODE BEGIN 2 */
  BSP_LED_Init(LED6);
  BSP_LED_Init(LED5);

  /* Checks if reset was because of wakeup from standby */
  if (__HAL_PWR_GET_FLAG(PWR_FLAG_SB) != RESET)
  {
    /* Clear Standby and wakeup flag */
    __HAL_PWR_CLEAR_FLAG(PWR_FLAG_SB | PWR_FLAG_WU);
    BSP_LED_On(LED5);
   /* Reset was from wakeup from standy */
  }
  else
  {
    BSP_LED_Off(LED5);
  }

  BSP_UART_Init(115200);
  uprintf("First LED is blinking in normal mode...\n\r");
  uprintf("Press '1' to enter system in standby mode.\n\r");
  uprintf("Wait 5s, RTC will wake-up system...\n\r");
  // BSP_RTC_Init();

  while(ugetche(NONE_BLOCKING) !='1')
  {
    BSP_LED_Toggle(LED6);
    HAL_Delay(500);
  }
  uprintf("\n\nEnter Deep PowerDown mode...\n\r");
  BSP_StandbyMode_PB();
  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
  /* USER CODE END WHILE */

  /* USER CODE BEGIN 3 */
    BSP_LED_Toggle(LED6);
    HAL_Delay(500);
  }
  /* USER CODE END 3 */


}