当前位置: 首页>>代码示例>>C++>>正文


C++ ADC_SoftwareStartConv函数代码示例

本文整理汇总了C++中ADC_SoftwareStartConv函数的典型用法代码示例。如果您正苦于以下问题:C++ ADC_SoftwareStartConv函数的具体用法?C++ ADC_SoftwareStartConv怎么用?C++ ADC_SoftwareStartConv使用的例子?那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。


在下文中一共展示了ADC_SoftwareStartConv函数的15个代码示例,这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞,您的评价将有助于系统推荐出更棒的C++代码示例。

示例1: temperature_MeasureValue

/**
  * @brief  Initializes the temperature sensor and its related ADC.
  * @param  None
  * @retval the float value of temperature measured in Celsius.
  */
float temperature_MeasureValue(void)
{	
	/* Raw value of temperature sensor voltage converted from ADC1_IN16 */
	uint16_t v_refint;
	/* Raw value of VREFINT converted from ADC1_INT17 */
	uint16_t v_sensor;
	
	/* select ADC1_IN16 to sample sensor voltage value*/
	ADC_RegularChannelConfig(ADC1, ADC_Channel_16, 1, ADC_SampleTime_28Cycles);
	/* start one ADC conversion */
	ADC_SoftwareStartConv(ADC1);
	/*  wait unitl ECO bit is set, sample finished */
	while(ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) == RESET);
	ADC_ClearFlag(ADC1, ADC_FLAG_EOC);
	/* Read the value from ADC_DR*/
	v_sensor = ADC_GetConversionValue(ADC1);

	/* select ADC1_IN16 to sample reference voltage value*/
	ADC_RegularChannelConfig(ADC1, ADC_Channel_17, 1, ADC_SampleTime_28Cycles);
	/* start one ADC conversion */
	ADC_SoftwareStartConv(ADC1);
	/*  wait unitl ECO bit is set, sample finished */
	while(ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) == RESET);
	ADC_ClearFlag(ADC1, ADC_FLAG_EOC);
	/* Read the value from ADC_DR*/
	v_refint = ADC_GetConversionValue(ADC1);

  /*
	 * measured_sensor_voltage = actual_reference_voltage * sampled_sensor_voltage / sampled_reference_voltage_value
	 * temperature = (measured_sensor_voltage - sensor_voltage_at_25) / AVG_SLOPE + 25
	 */
	return (VREFINT_VOLTAGE_V / v_refint * v_sensor - TEMPERATURE_V25) * 1000 / AVG_SLOPE + 25;
}
开发者ID:headyin,项目名称:Wireless-Board-Orientation-Control-System-ARM-Micro-Processor-Lab-,代码行数:38,代码来源:temperature.c

示例2: ubasic_get_adc

/*---------------------------------------------------------------------------*/
int ubasic_get_adc(int ch)
{
	int var = 0xff;
	switch(ch){
		case 1:
			if (ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) == RESET) {
				var = 0xff;
			} else {
				var = ADC_GetConversionValue(ADC1) & 0x00ff;
				ADC_SoftwareStartConv(ADC1);
			}
			break;
		case 2:
			if (ADC_GetFlagStatus(ADC2, ADC_FLAG_EOC) == RESET) {
				var = 0xff;
			} else {
				var = ADC_GetConversionValue(ADC2) & 0x00ff;
				ADC_SoftwareStartConv(ADC2);
			}
			break;
		case 3:
			if (ADC_GetFlagStatus(ADC3, ADC_FLAG_EOC) == RESET) {
				var = 0xff;
			} else {
				var = ADC_GetConversionValue(ADC3) & 0x00ff;
				ADC_SoftwareStartConv(ADC3);
			}
			break;
		default:
			var = 0xff;
			break;
	}
	return var;
}
开发者ID:mizuki-tohru,项目名称:stm32f4-console,代码行数:35,代码来源:ubasic.c

示例3: _ADC_Init

void _ADC_Init(void) {
ADC_InitTypeDef ADC_InitStructure;
ADC_CommonInitTypeDef ADC_CommonInitStruct;
		
//Enabling ADC clock
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC2, ENABLE);

//ADC common init configuration for Multi mode ADC
	ADC_CommonInitStruct.ADC_Mode = ADC_DualMode_RegSimult;
  ADC_CommonInitStruct.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled; //ADC_DMAAccessMode_Disabled; ADC_DMAAccessMode_1; ADC_DMAAccessMode_2; ADC_DMAAccessMode_3 
	ADC_CommonInitStruct.ADC_Prescaler = ADC_Prescaler_Div2; //ADC_Prescaler_Div2; ADC_Prescaler_Div4; ADC_Prescaler_Div6; ADC_Prescaler_Div8
	ADC_CommonInitStruct.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles; //ADC_TwoSamplingDelay_5Cycles - i tak dalej po 1 do 20 cykli	
	ADC_CommonInit(&ADC_CommonInitStruct);
	
//ADC1 configuration
	ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
	ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
	ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC1; //Timer
	ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_Rising;
	ADC_InitStructure.ADC_NbrOfConversion = 1;
	ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
	ADC_InitStructure.ADC_ScanConvMode = DISABLE; 
	ADC_Init(ADC1,&ADC_InitStructure);
	
//ADC2 configuration
	ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
	ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
	ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC1; //Timer
	ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_Rising;
	ADC_InitStructure.ADC_NbrOfConversion = 1;
	ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
	ADC_InitStructure.ADC_ScanConvMode = DISABLE; 
	ADC_Init(ADC2,&ADC_InitStructure);

//Regular channels config
	ADC_RegularChannelConfig(ADC1,ADC_Channel_9,1,ADC_SampleTime_144Cycles);
	ADC_RegularChannelConfig(ADC2,ADC_Channel_2,1,ADC_SampleTime_144Cycles);

//DMA for Multi mode ADC
	ADC_MultiModeDMARequestAfterLastTransferCmd(ENABLE);
	
//Activating continuous mode
	ADC_ContinuousModeCmd(ADC1, ENABLE);
	ADC_ContinuousModeCmd(ADC2, ENABLE);

//Enabling ADC	
	ADC_Cmd(ADC1, ENABLE);
	ADC_Cmd(ADC2, ENABLE);

	ADC_SoftwareStartConv(ADC1);
	ADC_SoftwareStartConv(ADC2);
}
开发者ID:OlendAr,项目名称:PodstawyPrzetwarzaniaSygnalow,代码行数:53,代码来源:main.c

示例4: adc_read

uint16_t adc_read(uint8_t channel){
  uint16_t vref;
  ADC_RegularChannelConfig(ADC1, ADC_Channel_Vrefint, 0, ADC_SampleTime_384Cycles);
  ADC_SoftwareStartConv(ADC1);
  while(ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) == RESET);
  vref=ADC_GetConversionValue(ADC1);

  ADC_RegularChannelConfig(ADC1, channel, 0, ADC_SampleTime_384Cycles);
  ADC_SoftwareStartConv(ADC1);
  while(ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) == RESET);
  return ADC_GetConversionValue(ADC1)*6840/vref; // magic number to get millivolts

}
开发者ID:zbanks,项目名称:hackboard,代码行数:13,代码来源:hal.c

示例5: getTemp_celcius

// fill this in
float getTemp_celcius() {
	ADC_SoftwareStartConv(ADC1);
	while(ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) == RESET);
	ADC_ClearFlag(ADC1, ADC_FLAG_EOC);

	return ((ADC1->DR * 3000.0/4096.0) - 760)/2.5 + 25;
}
开发者ID:cmtm,项目名称:microP,代码行数:8,代码来源:ADC.c

示例6: main

int main(void)
{
//init:
    DAC_DeInit();
	init_GPIOA();
    init_GPIOC();
    init_GPIOD();
    init_DMA1();
    init_DMA2();
    init_TIM2();
    init_TIM3();
    init_TIM4();
    init_TIM6();
    init_ADC3();
	init_DAC();
	init_filter(&ap_1);
	init_filter(&ap_2);
	init_filter(&ap_3);
	init_filter(&ap_4);
	ap_filter_coefs(&ap_1);
	ap_filter_coefs(&ap_2);
	ap_filter_coefs(&ap_3);
	ap_filter_coefs(&ap_4);
    ADC_SoftwareStartConv(ADC3);
    while (1)
    {
		counter++;
    }
}
开发者ID:3spds,项目名称:stm32f4,代码行数:29,代码来源:main_filt_a.c

示例7: main

/**
  * @brief  Main program.
  * @param  None
  * @retval None
  */
void main(void)
{
  /* CLK configuration -------------------------------------------*/
  CLK_Config(); 

  /* ADC configuration -------------------------------------------*/
  ADC_Config(); 

  /* DMA configuration -------------------------------------------*/
  DMA_Config(); 

  /* TIM1 configuration -------------------------------------------*/
  TIM1_Config(); 

  /* Enable ADC1 DMA requests*/
  ADC_DMACmd(ADC1, ENABLE);

  /* Enable TIM1 DMA requests*/
  TIM1_DMACmd(TIM1_DMASource_Update, ENABLE);

  /* Start ADC1 Conversion using Software trigger*/
  ADC_SoftwareStartConv(ADC1);

  while (1)
  {}
}
开发者ID:avr-master,项目名称:Healty_Beck,代码行数:31,代码来源:main.c

示例8: sampleADC

char sampleADC(void)
{
    char res = 0x0;

    CLK_PeripheralClockConfig(CLK_Peripheral_ADC1, ENABLE);
    ADC_DeInit(ADC1);

    ADC_VrefintCmd(ENABLE);
    delay_10us(3);

    ADC_Cmd(ADC1, ENABLE);
    ADC_Init(ADC1, ADC_ConversionMode_Single,
             ADC_Resolution_6Bit, ADC_Prescaler_1);

    ADC_SamplingTimeConfig(ADC1, ADC_Group_SlowChannels, ADC_SamplingTime_9Cycles);
    ADC_ChannelCmd(ADC1, ADC_Channel_0, ENABLE);
    delay_10us(3);

    ADC_SoftwareStartConv(ADC1);
    while( ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) == 0);
    res = (char)ADC_GetConversionValue(ADC1);

    ADC_VrefintCmd(DISABLE);
    ADC_DeInit(ADC1);

    /* disable SchmittTrigger for ADC_Channel_24, to save power */
    //ADC_SchmittTriggerConfig(ADC1, ADC_Channel_24, DISABLE);

    CLK_PeripheralClockConfig(CLK_Peripheral_ADC1, DISABLE);
    ADC_ChannelCmd(ADC1, ADC_Channel_0, DISABLE);

    return res;
}
开发者ID:david1mdavis,项目名称:SnapOnControls,代码行数:33,代码来源:main.c

示例9: ADC_Config

/**
  * @brief  Configures the ADC1 channel5.
  * @param  None
  * @retval None
  */
void ADC_Config(void)
{
  /* Enable The HSI (16Mhz) */
  RCC_HSICmd(ENABLE);

  /* Enable the GPIOF or GPIOA Clock */
  RCC_AHBPeriphClockCmd(IDD_MEASUREMENT_GPIO_CLK, ENABLE);
  /* Configure PF.11 (ADC Channel11) or PA.05 (ADC Channe5) in analog mode */
  GPIO_InitStructure.GPIO_Pin =  IDD_MEASUREMENT_PIN;
  GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_AN;
  GPIO_InitStructure.GPIO_PuPd  = GPIO_PuPd_NOPULL;
  GPIO_Init(IDD_MEASUREMENT_GPIO, &GPIO_InitStructure);

  /* Check that HSI oscillator is ready */
  while(RCC_GetFlagStatus(RCC_FLAG_HSIRDY) == RESET);

  /* ADC1 Configuration ------------------------------------------------------*/
  
  /* Enable ADC1 clock */
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
  
#ifdef USE_STM32L152D_EVAL
  /* Select ADC Bank channel */
  ADC_BankSelection(ADC1, ADC_Bank_B);
#endif
  
  ADC_StructInit(&ADC_InitStructure);
  ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
  ADC_InitStructure.ADC_ScanConvMode = DISABLE;
  ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
  ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
  ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
  ADC_InitStructure.ADC_NbrOfConversion = 1;
  ADC_Init(ADC1, &ADC_InitStructure);

  /* ADC1 regular channel5 or channel1 configuration */
  ADC_RegularChannelConfig(ADC1, IDD_MEASUREMENT_ADC_CHANNEL, 1, ADC_SampleTime_192Cycles);

  /* Define delay between ADC1 conversions */
  ADC_DelaySelectionConfig(ADC1, ADC_DelayLength_Freeze);
  
  /* Enable ADC1 Power Down during Delay */
  ADC_PowerDownCmd(ADC1, ADC_PowerDown_Idle_Delay, ENABLE);
  
  /* Enable ADC1 */
  ADC_Cmd(ADC1, ENABLE);

  /* Wait until ADC1 ON status */
  while (ADC_GetFlagStatus(ADC1, ADC_FLAG_ADONS) == RESET)
  {
  }

  /* Start ADC1 Software Conversion */
  ADC_SoftwareStartConv(ADC1);

  /* Wait until ADC Channel 5 or 1 end of conversion */
  while (ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) == RESET)
  {
  }
}
开发者ID:Amna2013,项目名称:stm32-test,代码行数:65,代码来源:main.c

示例10: vhADC_initADC

/*-----------------------------------------------------------
* @brief Function Name  : vhADC_initADC
* @brief Description    : Initializes ADC
*/
void vhADC_initADC(void){
	/* ADC Common initialization */
	ADC_CommonInitTypeDef ADC_CommonInitStructure;

	ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
	ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div6;		// 84MHz / prescaler(6) = 14MHz (max 30 OR 36... idk)
	ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
	ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
	ADC_CommonInit(&ADC_CommonInitStructure);

	ADC_InitTypeDef ADC_InitStructure;
	ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
	ADC_InitStructure.ADC_ScanConvMode = ENABLE;			// Enable, because we want to measure more than 1 channel
	ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;
	ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_RisingFalling;
	ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC1;
	ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
	ADC_InitStructure.ADC_NbrOfConversion = 2;
	ADC_Init(ADC1, &ADC_InitStructure);

	/* ADCx regular channel configuration */
	ADC_RegularChannelConfig(ADC1, ADC_Channel_10, 1, ADC_SampleTime_28Cycles);
	ADC_RegularChannelConfig(ADC1, ADC_Channel_14, 2, ADC_SampleTime_28Cycles);

	/* Enable DMA request after last transfer (Single-ADC mode) */
	ADC_DMARequestAfterLastTransferCmd(ADC1, ENABLE);

	/* Enable ADCx DMA */
	ADC_DMACmd(ADC1, ENABLE);

	/* Enable ADCx */
	ADC_Cmd(ADC1, ENABLE);

	ADC_SoftwareStartConv(ADC1);
}
开发者ID:bharathvu,项目名称:AUTOPILOT-1,代码行数:39,代码来源:ADC.c

示例11: ADC_AcquireData

void ADC_AcquireData()
{
  
	/* Enable ADC clock */
  //RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
 
  /* Enable ADC1 */
  //ADC_Cmd(ADC1, ENABLE);

  /* Wait until the ADC1 is ready */
  //while(ADC_GetFlagStatus(ADC1, ADC_FLAG_ADONS) == RESET); 

  /* Disable DMA mode for ADC1 */ 
  ADC_DMACmd(ADC1, DISABLE);
	
	ADC_DMA_init();
	
   /* Enable DMA mode for ADC1 */  
  ADC_DMACmd(ADC1, ENABLE);
  
//  /* Clear global flag for DMA transfert complete */
//  clearADCDMA_TransferComplete(); 
  
  /* Start ADC conversion */
  ADC_SoftwareStartConv(ADC1);
}
开发者ID:tarasii,项目名称:BMP085,代码行数:26,代码来源:adc.c

示例12: taskENTER_CRITICAL

void InternalTempSensor::measureTemp(bool calibrate)
{
    // ADC Conversion to read temperature sensor
    // Temperature (in °C) = ((Vsense – V25) / Avg_Slope) + 25
    // Vense = Voltage Reading From Temperature Sensor
    // V25 = Voltage at 25°C, for STM32F407 = 0.76V
    // Avg_Slope = 2.5mV/°C
    // This data can be found in the STM32F407VF Data Sheet


    taskENTER_CRITICAL();
    ADC_SoftwareStartConv(ADC1); //Start the conversion
    while (ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) == RESET) {} ; //Processing the conversion

    temp = ADC_GetConversionValue(ADC1); //Return the converted data
    temp *= 3300;
    temp /= 0xfff; //Reading in mV
    temp /= 1000.0; //Reading in Volts
    temp -= 0.760; // Subtract the reference voltage at 25°C
    temp /= .0025; // Divide by slope 2.5mV
    temp += 25.0; // Add the 25°C

    if (calibrate)
    {
        temp -= calibration;
    }

    taskEXIT_CRITICAL();
}
开发者ID:r00li,项目名称:RhomeV3,代码行数:29,代码来源:TempSensor.cpp

示例13: ADC_Supply

/**
  * @brief  To return the supply measurmeent
  * @caller several functions
  * @param None
  * @retval ADC value
  */ 
uint16_t ADC_Supply(void)
{
  uint8_t i;
  uint16_t res;

    /* Initializes ADC */
  ADC_Icc_Init();
 
  ADC_TempSensorVrefintCmd(ENABLE);

  /* ADC1 regular channel 17 for VREF configuration */
  ADC_RegularChannelConfig(ADC1, ADC_Channel_17, 1, ADC_SampleTime_192Cycles);
  
  /* initialize result */
  res = 0;
  for(i=4; i>0; i--)
  {
  /* start ADC convertion by software */
    ADC_SoftwareStartConv(ADC1);

    /* wait until end-of-covertion */
    while( ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC) == 0 );
  /* read ADC convertion result */
    res += ADC_GetConversionValue(ADC1);
  }
	
  /* de-initialize ADC */
  ADC_TempSensorVrefintCmd(DISABLE);
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, DISABLE);
  
  return (res>>2);
}
开发者ID:bzdegluk,项目名称:ACQ,代码行数:38,代码来源:icc_measure.c

示例14: Init_ADC3

//ADC3 initianilize
void Init_ADC3(void)
{
    ADC_InitTypeDef       ADC_InitStructure;
    ADC_CommonInitTypeDef ADC_CommonInitStructure;
     
    /* Enable ADC1 clock ********************************************************/
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC3, ENABLE);
     
    /* ADC Common Init **********************************************************/
    ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
    ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div2;
    ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
    ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
    ADC_CommonInit(&ADC_CommonInitStructure);
     
    /* ADC1 Init ****************************************************************/
    ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
    ADC_InitStructure.ADC_ScanConvMode = DISABLE;
    ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;
    ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
    ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
    ADC_InitStructure.ADC_NbrOfConversion = 1;
    ADC_Init(ADC3, &ADC_InitStructure);
    ADC_EOCOnEachRegularChannelCmd(ADC3, ENABLE);
    ADC_Cmd(ADC3, ENABLE);
    ADC_SoftwareStartConv(ADC3);
}
开发者ID:turboman1234,项目名称:TankController,代码行数:28,代码来源:adc.c

示例15: AdcMcuRead

uint16_t AdcMcuRead( Adc_t *obj, uint8_t channel )
{
    uint16_t adcData = 0;

    /* Enable The HSI (16Mhz) */
    RCC_HSICmd( ENABLE );

    /* Check that HSI oscillator is ready */
    while( RCC_GetFlagStatus( RCC_FLAG_HSIRDY ) == RESET );

    RCC_APB2PeriphClockCmd( RCC_APB2Periph_ADC1, ENABLE );

    // Temperature or Vref measurement
    if( ( channel == ADC_Channel_16 ) || ( channel == ADC_Channel_17 ) )
    {
        // Yes, enable temperature sensor and internal reference voltage
        ADC_TempSensorVrefintCmd( ENABLE );
    }

    // Configure selected channel
    ADC_RegularChannelConfig( ADC1, channel, 1, ADC_SampleTime_192Cycles );

    /* Define delay between ADC1 conversions */
    ADC_DelaySelectionConfig( ADC1, ADC_DelayLength_Freeze );

    /* Enable ADC1 Power Down during Delay */
    ADC_PowerDownCmd( ADC1, ADC_PowerDown_Idle_Delay, ENABLE );

    /* Enable ADC1 */
    ADC_Cmd( ADC1, ENABLE );

    /* Wait until ADC1 ON status */
    while( ADC_GetFlagStatus( ADC1, ADC_FLAG_ADONS ) == RESET )
    {
    }

    /* Start ADC1 Software Conversion */
    ADC_SoftwareStartConv( ADC1 );

    /* Wait until ADC Channel 5 or 1 end of conversion */
    while( ADC_GetFlagStatus( ADC1, ADC_FLAG_EOC ) == RESET )
    {
    }

    adcData = ADC_GetConversionValue( ADC1 );

    ADC_Cmd( ADC1, DISABLE );
    
    if( ( channel == ADC_Channel_16 ) || ( channel == ADC_Channel_17 ) )
    {
        // De-initialize ADC
        ADC_TempSensorVrefintCmd( DISABLE );    
    }

    RCC_APB2PeriphClockCmd( RCC_APB2Periph_ADC1, DISABLE );

    RCC_HSICmd( DISABLE );
   
    return adcData;
}
开发者ID:AlessandroLipari,项目名称:LoRaMac-node,代码行数:60,代码来源:adc-board.c


注:本文中的ADC_SoftwareStartConv函数示例由纯净天空整理自Github/MSDocs等开源代码及文档管理平台,相关代码片段筛选自各路编程大神贡献的开源项目,源码版权归原作者所有,传播和使用请参考对应项目的License;未经允许,请勿转载。