当前位置: 首页>>代码示例>>C++>>正文

C++ ADC_CommonInit函数代码示例

本文整理汇总了C++中ADC_CommonInit函数的典型用法代码示例。如果您正苦于以下问题：C++ ADC_CommonInit函数的具体用法？C++ ADC_CommonInit怎么用？C++ ADC_CommonInit使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。


在下文中一共展示了ADC_CommonInit函数的15个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于系统推荐出更棒的C++代码示例。

示例1: adcInit

void adcInit(void)
{
  /*
   * Note: This function initializes only ADC2, and only for single channel, single conversion mode. No DMA, no interrupts, no bells or whistles.
   */

  /* Note that this de-initializes registers for all ADCs (ADCx) */
  ADC_DeInit();

  /* Define ADC init structures */
  ADC_InitTypeDef       ADC_InitStructure;
  ADC_CommonInitTypeDef ADC_CommonInitStructure;

  /* Populates structures with reset values */
  ADC_StructInit(&ADC_InitStructure);
  ADC_CommonStructInit(&ADC_CommonInitStructure);

  /* enable ADC clock */
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC2, ENABLE);

  /* init ADCs in independent mode, div clock by two */
  ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
  ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div2; /* HCLK = 168MHz, PCLK2 = 84MHz, ADCCLK = 42MHz (when using ADC_Prescaler_Div2) */
  ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
  ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
  ADC_CommonInit(&ADC_CommonInitStructure);

  /* Init ADC2: 12bit, single-conversion. For Arduino compatibility set 10bit */
  analogReadResolution(12);

  /* Enable ADC2 */
  ADC_Cmd(ADC2, ENABLE);
}
开发者ID:CarlosRDomin，项目名称:crazyflie-firmware，代码行数:33，代码来源:deck_analog.c

示例2: adc_init

void adc_init(void) {
  // Initialize ADC
  ADC_CommonInitTypeDef ConfigCADC;
  ADC_CommonStructInit(&ConfigCADC);
  ADC_CommonInit(&ConfigCADC);

  // Initialize ADC1 & ADC2
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1 | RCC_APB2Periph_ADC2, ENABLE);
  ADC_InitTypeDef ConfigADC;
  ADC_StructInit(&ConfigADC);
  ADC_Init(ADC1, &ConfigADC);
  ADC_Init(ADC2, &ConfigADC);

/*#define ADC_Channel_TempSensor                      ((uint8_t)ADC_Channel_16)
#define ADC_Channel_Vrefint                         ((uint8_t)ADC_Channel_17)
#define ADC_Channel_Vbat                            ((uint8_t)ADC_Channel_18)
*/
  // Configure channels
  ADC_RegularChannelConfig(ADC1, ADC_Channel_2,  1, ADC_SampleTime_15Cycles); // Battery voltage
  ADC_RegularChannelConfig(ADC2, ADC_Channel_14, 1, ADC_SampleTime_15Cycles); // Light sensor

  // Enable ADC1 & 2
  ADC_Cmd(ADC1, ENABLE);
  ADC_Cmd(ADC2, ENABLE);

}
开发者ID:stg，项目名称:SmartWatch_Toolchain，代码行数:26，代码来源:driver_adc.c

示例3: initSensors

void initSensors()
{
	ADC_DeInit();
	// Setup ADC_CommonInitType first
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
	ADC_CommonInitStruct.ADC_Prescaler = ADC_Prescaler_Div8;
	ADC_CommonInitStruct.ADC_Mode = ADC_Mode_Independent;
	ADC_CommonInitStruct.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
	ADC_CommonInitStruct.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
	ADC_CommonInit(&ADC_CommonInitStruct);
	// Setup ADC_InitStruct
	ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
	ADC_InitStructure.ADC_ScanConvMode = DISABLE;
	ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
	ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
	ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC1;
	ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
	ADC_InitStructure.ADC_NbrOfConversion = 1;
	ADC_Init(ADC1, &ADC_InitStructure);
	ADC_RegularChannelConfig(ADC1, ADC_Channel_10, 1, ADC_SampleTime_3Cycles);
	ADC_Cmd(ADC1, ENABLE);

	ADC_ResetCalibration(ADC1);
	//Enable ADC1 reset calibration register
	ADC_ResetCalibration(ADC1);
	//Check the end of ADC1 reset calibration register
	while(ADC_GetResetCalibrationStatus(ADC1));
	//Start ADC1 calibration
	ADC_StartCalibration(ADC1);
	//Check the end of ADC1 calibration
	while(ADC_GetCalibrationStatus(ADC1));
	//Start ADC1 Software Conversion
	ADC_SoftwareStartConvCmd(ADC1, ENABLE);
}
开发者ID:Apo11oH，项目名称:micromouse_2014，代码行数:34，代码来源:adc.c

示例4: adcSetup

void adcSetup(void){
		
	   ADC_DeInit();

		 RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);

		 ADC_CommonInitStruct.ADC_Mode = ADC_Mode_Independent;
		 ADC_CommonInitStruct.ADC_Prescaler = ADC_Prescaler_Div8;
		 ADC_CommonInitStruct.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
		 ADC_CommonInitStruct.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
		 ADC_CommonInit(&ADC_CommonInitStruct);

		 ADC_InitStruct.ADC_Resolution = ADC_Resolution_12b;
		 ADC_InitStruct.ADC_ScanConvMode = DISABLE;
		 ADC_InitStruct.ADC_ContinuousConvMode = ENABLE;
		 ADC_InitStruct.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
		 ADC_InitStruct.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC1;
		 ADC_InitStruct.ADC_DataAlign = ADC_DataAlign_Right;
		 ADC_InitStruct.ADC_NbrOfConversion = 1;
		 ADC_Init(ADC1, &ADC_InitStruct);

			// ADC1 Configuration, ADC_Channel_TempSensor is actual channel 16
		 ADC_RegularChannelConfig(ADC1, ADC_Channel_TempSensor, 1, ADC_SampleTime_144Cycles);

			// Enable internal temperature sensor
		 ADC_TempSensorVrefintCmd(ENABLE);

			// Enable ADC conversion
		 ADC_Cmd(ADC1, ENABLE);
}
开发者ID:rmursh，项目名称:MicroP-ECSE426，代码行数:30，代码来源:TemperatureSensor.c

示例5: P_ADC2s_InitADC

//--------------------------------------------------------------
// interne Funktion
// Init von ADC Nr.2
//--------------------------------------------------------------
void P_ADC2s_InitADC(void)
{
  ADC_CommonInitTypeDef ADC_CommonInitStructure;
  ADC_InitTypeDef       ADC_InitStructure;

  // Clock Enable
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC2, ENABLE);

  // ADC-Config
  ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
  ADC_CommonInitStructure.ADC_Prescaler = ADC2s_VORTEILER;
  ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
  ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
  ADC_CommonInit(&ADC_CommonInitStructure);

  ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
  ADC_InitStructure.ADC_ScanConvMode = DISABLE;
  ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;
  ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
  ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
  ADC_InitStructure.ADC_NbrOfConversion = 1;
  ADC_Init(ADC2, &ADC_InitStructure);

  // ADC-Enable
  ADC_Cmd(ADC2, ENABLE);
}
开发者ID:Jinzuu，项目名称:wc_ws，代码行数:30，代码来源:stm32_ub_adc2_single.c

示例6: RCC_AHB1PeriphClockCmd

void Battery::initialize(){
	GPIO_InitTypeDef GPIO_InitStructure;
	RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOC, ENABLE);
	GPIO_StructInit(&GPIO_InitStructure);
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
	GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_Init(GPIOC, &GPIO_InitStructure);

	ADC_InitTypeDef ADC_InitStructure;
	ADC_CommonInitTypeDef ADC_CommonInitStructure;

	RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC|RCC_APB2Periph_ADC1, ENABLE);
	RCC_AHB1PeriphClockCmd(RCC_AHB1ENR_GPIOCEN,ENABLE);
	ADC_DeInit();
	ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
	ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div4;
	ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
	ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
	ADC_CommonInit(&ADC_CommonInitStructure);

	ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
	ADC_InitStructure.ADC_ScanConvMode = DISABLE;
	ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
	ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
	ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
	ADC_InitStructure.ADC_NbrOfConversion = 1;
	ADC_Init(ADC1, &ADC_InitStructure);

	ADC_RegularChannelConfig(ADC1, ADC_Channel_14, 1, ADC_SampleTime_112Cycles);

	ADC_Cmd(ADC1, ENABLE);
	ADC_DMACmd(ADC1,DISABLE);
}
开发者ID:taniho0707，项目名称:nucleo_mouse，代码行数:35，代码来源:Battery.cpp

示例7: adcInit

void adcInit() {
		
	GPIO_InitTypeDef GPIO_InitStruct;
	ADC_CommonInitTypeDef ADC_CommonInitStruct;
	ADC_InitTypeDef ciguMigu;
	
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
	RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE); 	
	
	GPIO_StructInit(&GPIO_InitStruct);
  GPIO_InitStruct.GPIO_Pin  = GPIO_Pin_1;
  GPIO_InitStruct.GPIO_Mode = GPIO_Mode_AN;
  GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_Init(GPIOA, &GPIO_InitStruct);
	
	ADC_CommonStructInit(&ADC_CommonInitStruct);
	ADC_CommonInitStruct.ADC_Prescaler = ADC_Prescaler_Div4;
	ADC_CommonInit(&ADC_CommonInitStruct);
	
	ADC_StructInit(&ciguMigu);
	ciguMigu.ADC_Resolution = ADC_Resolution_10b;
	ADC_Init(ADC1, &ciguMigu);
	ADC_Cmd(ADC1, ENABLE);
	
	ADC_RegularChannelConfig(ADC1, ADC_Channel_1, 1, ADC_SampleTime_480Cycles);
}
开发者ID:rokrupnik，项目名称:vinokuh，代码行数:26，代码来源:adc_zdovc.c

示例8: config_driver_adc_1

static void config_driver_adc_1(void)
{
    ADC_InitTypeDef ADC_InitStructure;

    ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
    ADC_InitStructure.ADC_ScanConvMode = DISABLE;
    ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
    ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
    ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC1;
    ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
    ADC_InitStructure.ADC_NbrOfConversion = 1;
    ADC_Init(ADC1, &ADC_InitStructure);

    ADC_CommonInitTypeDef ADC_CommonInitStructure;

    ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
    ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div8;
    ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
    ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_20Cycles;
    ADC_CommonInit(&ADC_CommonInitStructure);

    ADC_RegularChannelConfig(ADC1, ADC_Channel_1, 1, ADC_SampleTime_480Cycles);
    ADC_DMARequestAfterLastTransferCmd(ADC1, ENABLE);
    ADC_DMACmd(ADC1, ENABLE);
    ADC_Cmd(ADC1, ENABLE);

    ADC_SoftwareStartConv(ADC1);
}
开发者ID:glocklueng，项目名称:ESP8266-STM32F4Discovery，代码行数:28，代码来源:adc_1.c

示例9: adc_tempsen

extern void adc_tempsen(){
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE); // adc1 kanalý clock aktif edildi




	    ADC_CommonInitTypeDef ADC_CommonInitStructure;
	    ADC_InitTypeDef       ADC_InitStructure;

	    ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
	    ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div2;
	    ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
	    ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_20Cycles;

	    ADC_CommonInit(&ADC_CommonInitStructure);

	    ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
	    ADC_InitStructure.ADC_ScanConvMode = DISABLE;
	    ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;
	    ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
	    ADC_InitStructure.ADC_ExternalTrigConv =0;
	    ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
	    ADC_InitStructure.ADC_NbrOfConversion = 1;



	    ADC_Init(ADC1, &ADC_InitStructure);
	    ADC_RegularChannelConfig(ADC1,ADC_Channel_TempSensor, 1, ADC_TwoSamplingDelay_5Cycles);
        ADC_TempSensorVrefintCmd(ENABLE);

	    ADC_Cmd(ADC1, ENABLE);


}
开发者ID:bolatberk，项目名称:stm32f407vg，代码行数:34，代码来源:stm32_adc.c

示例10: Sensor_Configuration

void Sensor_Configuration(void) {
	ADC_CommonInitTypeDef ADC_CommonInitStructure;
	GPIO_InitTypeDef GPIO_InitStructure;

	SensorGPIO_Configuration();
	DMA2_Configuration();

	GPIO_StructInit(&GPIO_InitStructure);
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_2 | GPIO_Pin_3 |
									GPIO_Pin_4 | GPIO_Pin_5 | GPIO_Pin_6 | GPIO_Pin_7;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
	GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
	GPIO_Init(GPIOA, &GPIO_InitStructure);

	ADC_CommonInitStructure.ADC_Mode = ADC_DualMode_RegSimult;
	ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div2;
	ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_1;
	ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_20Cycles;
	ADC_CommonInit(&ADC_CommonInitStructure);

	ADC1_Config();
	ADC2_Config();

	ADC_MultiModeDMARequestAfterLastTransferCmd(ENABLE);

	ADC_Cmd(ADC1, ENABLE);
	ADC_Cmd(ADC2, ENABLE);

	ADC_DMACmd(ADC1, ENABLE);

	ADC_SoftwareStartConv(ADC1);
}
开发者ID:vpcola，项目名称:stm32f4，代码行数:32，代码来源:sensor.c

示例11: temperature_setup

int temperature_setup() 
{
	ADC_InitTypeDef adc_init_s;														//Initializes definitions of SDC
	ADC_CommonInitTypeDef adc_common_init_s;							//Used to def common paramters for ADC peripheral
	
	ADC_DeInit();																					//reset ADC peripheral value to their defaults
	
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);	//Enable Power for APB2 bus connected to ADC1 (temp sensor)

	adc_common_init_s.ADC_Mode = ADC_Mode_Independent; 		//Configures the ADC for indepedent mode
	adc_common_init_s.ADC_Prescaler = ADC_Prescaler_Div2; //Sets Frequency of the clock to ADC. Count 0 and 1.
	adc_common_init_s.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled; //turn off direct memory access mode
	adc_common_init_s.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles; //sets the delay between two sampling phases as 5
	
	ADC_CommonInit(&adc_common_init_s);										//initializes the struct for values set (above)
	
	adc_init_s.ADC_Resolution = ADC_Resolution_12b;				//Configures the ADC resolution 12 bits
	adc_init_s.ADC_ScanConvMode = DISABLE;								//sets conversion to Single channel mode
	adc_init_s.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None; //Set the external trigger edge to none
	adc_init_s.ADC_DataAlign = ADC_DataAlign_Right;				//MSB in register is 0, data saved starting from LSB
	adc_init_s.ADC_NbrOfConversion = 1; 									//Specifies the number of ADC conversions that will be done
	
	ADC_TempSensorVrefintCmd(ENABLE);											//wake up desired sensor (temp)
	ADC_Cmd(ADC1, ENABLE);																//turn on the ADC1 peripheral
	ADC_RegularChannelConfig(ADC1, ADC_Channel_16, 1, ADC_SampleTime_480Cycles);	//Configures ADC1_channel 16 which is the tempature sensor
	ADC_Init(ADC1, &adc_init_s);													//initialize ADC1
	

	new_filter.avg = 0, new_filter.replace = 0, new_filter.sum = 0;
	
	return 0;
}
开发者ID:kanetkarster，项目名称:MicroP-Lab2，代码行数:32，代码来源:temperature.c

示例12: ADCInit

void ADCInit()
{
       ADC_InitTypeDef ADC_InitStructure;
       ADC_StructInit(&ADC_InitStructure);

       ADC_CommonInitTypeDef adc_init;
       ADC_CommonStructInit(&adc_init);
       /* разрешаем тактирование AЦП1 */
       RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
       /* сбрасываем настройки АЦП */
       ADC_DeInit();
       ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
       /* АЦП1 и АЦП2 работают независимо */
       adc_init.ADC_Mode = ADC_Mode_Independent;
       adc_init.ADC_Prescaler = ADC_Prescaler_Div2;
       /* выключаем scan conversion */
       ADC_InitStructure.ADC_ScanConvMode = DISABLE;
       /* Не делать длительные преобразования */
       ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;
       /* Начинать преобразование программно, а не по срабатыванию триггера */
       ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConvEdge_None;
       /* 12 битное преобразование. результат в 12 младших разрядах результата */
       ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
       /* инициализация */
       ADC_CommonInit(&adc_init);
       ADC_Init(ADC1, &ADC_InitStructure);
       /* Включаем АЦП1 */
       ADC_Cmd(ADC1, ENABLE);

 // настройка канала
 ADC_RegularChannelConfig(ADC1, ADC_Channel_1, 1, ADC_SampleTime_15Cycles);
}
开发者ID:Olvar-ag，项目名称:RESET，代码行数:32，代码来源:main.c

示例13: ADC_DeInit

void InternalTempSensor::initTempSensor()
{
    temp = 0;
    calibration = 0;

    ADC_DeInit();

    ADC_InitTypeDef ADC_InitStruct;
    ADC_CommonInitTypeDef ADC_CommonInitStruct;

    RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);

    ADC_CommonInitStruct.ADC_Mode = ADC_Mode_Independent;
    ADC_CommonInitStruct.ADC_Prescaler = ADC_Prescaler_Div8;
    ADC_CommonInitStruct.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
    ADC_CommonInitStruct.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
    ADC_CommonInit(&ADC_CommonInitStruct);

    ADC_InitStruct.ADC_Resolution = ADC_Resolution_12b;
    ADC_InitStruct.ADC_ScanConvMode = DISABLE;
    ADC_InitStruct.ADC_ContinuousConvMode = ENABLE;
    ADC_InitStruct.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
    ADC_InitStruct.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC1;
    ADC_InitStruct.ADC_DataAlign = ADC_DataAlign_Right;
    ADC_InitStruct.ADC_NbrOfConversion = 1;
    ADC_Init(ADC1, &ADC_InitStruct);

    ADC_RegularChannelConfig(ADC1, ADC_Channel_TempSensor, 1, ADC_SampleTime_144Cycles);
    ADC_TempSensorVrefintCmd(ENABLE);
    ADC_Cmd(ADC1, ENABLE);
}
开发者ID:r00li，项目名称:RhomeV3，代码行数:31，代码来源:TempSensor.cpp

示例14: init_ADC3

void init_ADC3(void)
{
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC3, ENABLE);
    //ADC common init
	ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
    ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div2;
    ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
    ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
    ADC_CommonInit(&ADC_CommonInitStructure);
    //ADC3 init
    ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
    ADC_InitStructure.ADC_ScanConvMode = ENABLE;
    ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
    ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
    ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
    ADC_InitStructure.ADC_NbrOfConversion = nconversions;
    ADC_InitStructure.ADC_ExternalTrigConv=0x00;
    ADC_Init(ADC3, &ADC_InitStructure);
    // ADC3 regular configuration
    ADC_RegularChannelConfig(ADC3, ADC_Channel_12, 1, ADC_SampleTime_3Cycles);
    ADC_RegularChannelConfig(ADC3, ADC_Channel_11, 2, ADC_SampleTime_3Cycles);
    ADC_RegularChannelConfig(ADC3, ADC_Channel_10, 3, ADC_SampleTime_3Cycles);
    ADC_RegularChannelConfig(ADC3, ADC_Channel_9, 4, ADC_SampleTime_3Cycles);
	// Enable DMA request after last transfer
    ADC_DMARequestAfterLastTransferCmd(ADC3, ENABLE);
    ADC_DMACmd(ADC3, ENABLE);
    ADC_Cmd(ADC3, ENABLE);
}
开发者ID:3spds，项目名称:stm32f4，代码行数:28，代码来源:main_filt_a.c

示例15: Init_ADC3

//ADC3 initianilize
void Init_ADC3(void)
{
    ADC_InitTypeDef       ADC_InitStructure;
    ADC_CommonInitTypeDef ADC_CommonInitStructure;
     
    /* Enable ADC1 clock ********************************************************/
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC3, ENABLE);
     
    /* ADC Common Init **********************************************************/
    ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
    ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div2;
    ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
    ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
    ADC_CommonInit(&ADC_CommonInitStructure);
     
    /* ADC1 Init ****************************************************************/
    ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
    ADC_InitStructure.ADC_ScanConvMode = DISABLE;
    ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;
    ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
    ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
    ADC_InitStructure.ADC_NbrOfConversion = 1;
    ADC_Init(ADC3, &ADC_InitStructure);
    ADC_EOCOnEachRegularChannelCmd(ADC3, ENABLE);
    ADC_Cmd(ADC3, ENABLE);
    ADC_SoftwareStartConv(ADC3);
}
开发者ID:turboman1234，项目名称:TankController，代码行数:28，代码来源:adc.c


注：本文中的ADC_CommonInit函数示例由纯净天空整理自Github/MSDocs等开源代码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。