Python board.MOSI屬性代碼示例

# 需要導入模塊: import board [as 別名]
# 或者: from board import MOSI [as 別名]
def __init__(self):
        Sensor.__init__(self)

        self.moisture_min = float(self.config["soil"]["min"])
        self.moisture_max = float(self.config["soil"]["max"])

        # create SPI bus
        spi = busio.SPI(clock=board.SCK, MISO=board.MISO, MOSI=board.MOSI)

        # create the cs (chip select)
        cs = digitalio.DigitalInOut(board.D8)

        # create the mcp object
        mcp = MCP.MCP3008(spi, cs)
        
        # create an analog input channel
        self.pin = []
        self.pin.append(AnalogIn(mcp, MCP.P0))
        self.pin.append(AnalogIn(mcp, MCP.P1))
        self.pin.append(AnalogIn(mcp, MCP.P2))
        self.pin.append(AnalogIn(mcp, MCP.P3))
        self.pin.append(AnalogIn(mcp, MCP.P4))
        self.pin.append(AnalogIn(mcp, MCP.P5))
        self.pin.append(AnalogIn(mcp, MCP.P6))
        self.pin.append(AnalogIn(mcp, MCP.P7)) 

# 需要導入模塊: import board [as 別名]
# 或者: from board import MOSI [as 別名]
def __init__(self, config: dict, main_thread_running, system_ready):
        self.config = config
        self.main_thread_running = main_thread_running
        self.system_ready = system_ready
        self.node_ready = False

        spi = busio.SPI(clock=board.SCK, MISO=board.MISO, MOSI=board.MOSI)
        cs = digitalio.DigitalInOut(ADCMCP3008Worker.PINS[config['pin']])

        self.mcp = MCP.MCP3008(spi, cs)

        self.sensors = []
        self.init_sensors()

        self.node_ready = True 

# 需要導入模塊: import board [as 別名]
# 或者: from board import MOSI [as 別名]
def __init__(self, num_led=8, global_brightness=31,
                 order='rgb', mosi=10, sclk=11, ce=None, bus_speed_hz=8000000):
        """Initializes the library

        :param num_led: Number of LEDs in the strip
        :param global_brightness: Overall brightness
        :param order: Order in which the colours are addressed (this differs from strip to strip)
        :param mosi: Master Out pin. Use 10 for SPI0, 20 for SPI1, any GPIO pin for bitbang.
        :param sclk: Clock, use 11 for SPI0, 21 for SPI1, any GPIO pin for bitbang.
        :param ce: GPIO to use for Chip select. Can be any free GPIO pin. Warning: This will slow down the bus
                   significantly. Note: The hardware CE0 and CE1 are not used
        :param bus_speed_hz: Speed of the hardware SPI bus. If glitches on the bus are visible, lower the value.
        """
        self.num_led = num_led
        order = order.lower()  # Just in case someone use CAPS here.
        self.rgb = RGB_MAP.get(order, RGB_MAP['rgb'])
        self.global_brightness = global_brightness
        self.use_bitbang = False  # Two raw SPI devices exist: Bitbang (software) and hardware SPI.
        self.use_ce = False  # If true, use the BusDevice abstraction layer on top of the raw SPI device

        self.leds = [self.LED_START, 0, 0, 0] * self.num_led  # Pixel buffer
        if ce is not None:
            # If a chip enable value is present, use the Adafruit CircuitPython BusDevice abstraction on top
            # of the raw SPI device (hardware or bitbang)
            # The next line is just here to prevent an "unused" warning from the IDE
            digitalio.DigitalInOut(board.D1)
            # Convert the chip enable pin number into an object (reflection à la Python)
            ce = eval("digitalio.DigitalInOut(board.D"+str(ce)+")")
            self.use_ce = True
        # Heuristic: Test for the hardware SPI pins. If found, use hardware SPI, otherwise bitbang SPI
        if mosi == 10:
            if sclk != 11:
                raise ValueError("Illegal MOSI / SCLK combination")
            self.spi = busio.SPI(clock=board.SCLK, MOSI=board.MOSI)
        elif mosi == 20:
            if sclk != 21:
                raise ValueError("Illegal MOSI / SCLK combination")
            self.spi = busio.SPI(clock=board.SCLK_1, MOSI=board.MOSI_1)
        else:
            # Use Adafruit CircuitPython BitBangIO, because the pins do not match one of the hardware SPI devices
            # Reflection à la Python to get at the digital IO pins
            self.spi = bitbangio.SPI(clock=eval("board.D"+str(sclk)), MOSI=eval("board.D"+str(mosi)))
            self.use_bitbang = True
        # Add the BusDevice on top of the raw SPI
        if self.use_ce:
            self.spibus = SPIDevice(spi=self.spi,  chip_select=ce, baudrate=bus_speed_hz)
        else:
            # If the BusDevice is not used, the bus speed is set here instead
            while not self.spi.try_lock():
                pass
            self.spi.configure(baudrate=bus_speed_hz)
            self.spi.unlock()
        # Debug
        if self.use_ce:
            print("Use software chip enable")
        if self.use_bitbang:
            print("Use bitbang SPI")
        else:
            print("Use hardware SPI")