本文整理匯總了Golang中github.com/eris-ltd/eris-db/Godeps/_workspace/src/github.com/tendermint/tendermint/account.Account.Balance方法的典型用法代碼示例。如果您正苦於以下問題：Golang Account.Balance方法的具體用法？Golang Account.Balance怎麽用？Golang Account.Balance使用的例子？那麽, 這裏精選的方法代碼示例或許可以為您提供幫助。您也可以進一步了解該方法所在類github.com/eris-ltd/eris-db/Godeps/_workspace/src/github.com/tendermint/tendermint/account.Account的用法示例。
在下文中一共展示了Account.Balance方法的1個代碼示例，這些例子默認根據受歡迎程度排序。您可以為喜歡或者感覺有用的代碼點讚，您的評價將有助於係統推薦出更棒的Golang代碼示例。
示例1: ExecTx
//.........這裏部分代碼省略.........
signBytes := acm.SignBytes(_s.ChainID, tx)
err := validateInput(inAcc, signBytes, tx.Input)
if err != nil {
log.Info(Fmt("validateInput failed on %X: %v", tx.Input.Address, err))
return err
}
if tx.Input.Amount < tx.Fee {
log.Info(Fmt("Sender did not send enough to cover the fee %X", tx.Input.Address))
return types.ErrTxInsufficientFunds
}
if !createContract {
// Validate output
if len(tx.Address) != 20 {
log.Info(Fmt("Destination address is not 20 bytes %X", tx.Address))
return types.ErrTxInvalidAddress
}
// check if its a native contract
if vm.RegisteredNativeContract(LeftPadWord256(tx.Address)) {
return fmt.Errorf("NativeContracts can not be called using CallTx. Use a contract or the appropriate tx type (eg. PermissionsTx, NameTx)")
}
// Output account may be nil if we are still in mempool and contract was created in same block as this tx
// but that's fine, because the account will be created properly when the create tx runs in the block
// and then this won't return nil. otherwise, we take their fee
outAcc = blockCache.GetAccount(tx.Address)
}
log.Info(Fmt("Out account: %v", outAcc))
// Good!
value := tx.Input.Amount - tx.Fee
inAcc.Sequence += 1
inAcc.Balance -= tx.Fee
blockCache.UpdateAccount(inAcc)
// The logic in runCall MUST NOT return.
if runCall {
// VM call variables
var (
gas int64 = tx.GasLimit
err error = nil
caller *vm.Account = toVMAccount(inAcc)
callee *vm.Account = nil // initialized below
code []byte = nil
ret []byte = nil
txCache = NewTxCache(blockCache)
params = vm.Params{
BlockHeight: int64(_s.LastBlockHeight),
BlockHash: LeftPadWord256(_s.LastBlockHash),
BlockTime: _s.LastBlockTime.Unix(),
GasLimit: _s.GetGasLimit(),
}
)
if !createContract && (outAcc == nil || len(outAcc.Code) == 0) {
// if you call an account that doesn't exist
// or an account with no code then we take fees (sorry pal)
// NOTE: it's fine to create a contract and call it within one
// block (nonce will prevent re-ordering of those txs)
// but to create with one contract and call with another
// you have to wait a block to avoid a re-ordering attack
// that will take your fees
if outAcc == nil {
log.Info(Fmt("%X tries to call %X but it does not exist.",