C++ Delay_ms函數代碼示例

本文整理匯總了C++中Delay_ms函數的典型用法代碼示例。如果您正苦於以下問題：C++ Delay_ms函數的具體用法？C++ Delay_ms怎麽用？C++ Delay_ms使用的例子？那麽, 這裏精選的函數代碼示例或許可以為您提供幫助。

在下文中一共展示了Delay_ms函數的15個代碼示例，這些例子默認根據受歡迎程度排序。您可以為喜歡或者感覺有用的代碼點讚，您的評價將有助於係統推薦出更棒的C++代碼示例。

示例1: SF_rem

void SF_rem()
{
  unsigned char i,temp[6];
  char txte[4],txtex[4];
  int val=0;
  long adr=0x111111;

  for(i=0;i<6;i++) {
    temp[i] = SerialFlash_ReadByte(adr);
    ByteToStr(temp[i],txte);
    ByteToStr(arm[i],txtex);
    if(temp[i]!=arm[i]) val=1;
    adr+=0x000020;
  }

  Delay_ms(3000);
  for(i=0;i<6;i++) arm[i]=0;
  strcpy(Label24.Caption,"");
  DrawScreen(&System_Log_Screen);
  if(val==0) {
    a=0;
    Box30.Color=0x00008040;
    Box36.Color=0x00008040;
    Image65.Visible=1;
    Image66.Visible=0;
    strcpy(Label25.Caption,"DISARMED");
    strcpy(Label8.Caption,"DISARMED");
  }
}

開發者ID:MikroElektronika，項目名稱:mikromedia_HMI，代碼行數:29，代碼來源:Mikromedia_HMI_70C_Demo_main.c

示例2: Ctrlwifi

//************************************
//5.2WIFI控製
//******************************
Ctrlwifi()
{
  unchar i = 0;
  switch(MenuStatus)
  {
  case 2:
  //  POWRONWIFI;
    
    Str_8x16(1,0,"正在啟動WIFI");
    //Init_Uart1;
    while(!DialWIFI())
    {
      if(i++>5)
      {
       Str_8x16(1,0,"啟動WIFI失敗"); 
   //    POWEROFFWIF;
       Delay_ms(2000);
      MenuStatus = 3;
      return;
      }
  
    }
   Str_8x16(1,0,"啟動WIFI成功"); 
   WIFI_RX_CONNECT==2;//默認啟動文件傳輸。
   MenuStatus = 1000;       
    break;
  case 1000:
    //接收wifi客戶端軟件的命令。
    
    break;
    
    
  }
}

開發者ID:jwliu2016，項目名稱:handset，代碼行數:37，代碼來源:複件+(3)+func.c

示例3: main

void main() {            // ABRE FUNCAO PRINCIPAL: MAIN
ADCON1 = 0x06;           // CONFIGURA ENTRADAS AN COMO E/S DIGITAIS
CMCON = 7;               // DESLIGA COMPARADORES
// CONFIGURACOES E/S E ESTADOS INICIAIS [BINARIO]
TRISA = 0b00000000;            PORTA = 0b00000000;
TRISB = 0b00000000;            PORTB = 0b00000000;
TRISC = 0b00000000;            PORTC = 0b00000000;
TRISD = 0b00000000;            PORTD = 0b00000000;
TRISE = 0b00000000;            PORTE = 0b00000000;
// ESTADOS INICIAIS DOS ACESSORIOS
RELE_1 = 0;
RELE_2 = 0;
BARRA_LEDS_1 = 0;
BARRA_LEDS_2 = 0;
RESIST = 0;
VENT = 0;
BUZZER = 0;
// PISCAR OS ACESSORIOS INDEFINIDAMENTE
while (1){
RELE_1 =          ~ RELE_1;
RELE_2 =          ~ RELE_2;
BARRA_LEDS_1 =    ~ BARRA_LEDS_1;
BARRA_LEDS_2 =    ~ BARRA_LEDS_2;
RESIST =          ~ RESIST;
VENT =            ~ VENT;
BUZZER =          ~ BUZZER;
Delay_ms(750);
}             // FECHA WHILE
}             // FECHA MAIN

開發者ID:realronchi，項目名稱:progparamicroprocessadores，代碼行數:29，代碼來源:AULA.c

示例4: applicationTask

void applicationTask()
{
    int16_t valueX;
    int16_t valueY;
    int16_t valueZ;
    uint8_t txtX[ 15 ];
    uint8_t txtY[ 15 ];
    uint8_t txtZ[ 15 ];

    valueX = accel_readXaxis();
    valueY = accel_readYaxis();
    valueZ = accel_readZaxis();

    IntToStr( valueX, txtX );
    IntToStr( valueY, txtY );
    IntToStr( valueZ, txtZ );

    mikrobus_logWrite( " Axis X :", _LOG_TEXT );
    mikrobus_logWrite( txtX, _LOG_LINE );

    mikrobus_logWrite( " Axis Y :", _LOG_TEXT );
    mikrobus_logWrite( txtY, _LOG_LINE );

    mikrobus_logWrite( " Axis Z :", _LOG_TEXT );
    mikrobus_logWrite( txtZ, _LOG_LINE );

    mikrobus_logWrite("----------------", _LOG_LINE);

    Delay_ms( 5000 );
}

開發者ID:MikroElektronika，項目名稱:Click_Accel_ADXL345，代碼行數:30，代碼來源:Click_Accel_KINETIS.c

示例5: device_HW_reset

void device_HW_reset(void)
{
	GPIO_ResetBits(WIZ_RESET_PORT, WIZ_RESET_PIN);
	Delay_us(8);
	GPIO_SetBits(WIZ_RESET_PORT, WIZ_RESET_PIN);
	Delay_ms(50);
}

開發者ID:ConvTeam，項目名稱:WIZlib，代碼行數:7，代碼來源:wizplatform.c

示例6: gsm4_send_sms

void gsm4_send_sms( uint8_t* rsp, uint8_t rsp_len )
{
    at_cmd( "AT+CMGS=\"0643280993\"" );
    at_cmd_addition( "Hello it's me, Hexiwear! :)" );
    Delay_ms( 1000 );
    sent_f = true;
}

開發者ID:MikroElektronika，項目名稱:HEXIWEAR，代碼行數:7，代碼來源:gsm4.c

示例7: pw1_pid

static void pw1_pid(void)
{
	rt_uint32_t key_value;
//	static double coefy2a = 0.8;
    
	while(1)
	{
		LCD_Clear();
		LCD_SetXY(0,0);     LCD_WriteString("=====sonic_test=====");
		LCD_SetXY(0, 1);    LCD_WriteString("1.front pid");
        LCD_SetXY(0, 2);    LCD_WriteString("2.f->pid");
        LCD_SetXY(0, 3);    LCD_WriteString("3.side pid");
        LCD_SetXY(0, 4);    LCD_WriteString("4.s->pid"); 
        LCD_SetXY(10, 1);   LCD_WriteString("5.fs pid");
		
		if(rt_mb_recv(&Mb_Key, &key_value, RT_WAITING_NO) == RT_EOK)
		{
			switch(key_value)
			{
				case key1:      pole_sonic(0x01);                break;
				case key2:      _input_pid(&sPos_Pid[eF_sonic]); break; 
                case key3:      pole_sonic(0x02);                break; 
                case key4:      _input_pid(&sPos_Pid[eS_sonic]); break;
                case key5:      pole_sonic(0x03);                break;
                case keyback:   return;
			}
		}
		Delay_ms(10);
	}
}

開發者ID:yihui-he，項目名稱:Badminton-Robot，代碼行數:30，代碼來源:sonic1.c

示例8: testNOR

uint32_t testNOR(uint32_t startAddress, uint32_t size, uint16_t bufferSize) {
	uint8_t index;
	uint16_t numWord;
	uint16_t check;
	uint8_t startBlock = startAddress / NORFLASH_SECTOR_SIZE;
	uint8_t endBlock = (startAddress + size) / NORFLASH_SECTOR_SIZE;
	NORFLASH_Status status;
	NORFLASH_Id chipId;

	NORFLASH_Init();
//	for (index = startBlock; index <= endBlock; index++) {
//		status = NORFLASH_EraseBlockNum(index);
//	}
//	SerialSendBytes("Start writing.\r\n", 16);
//	for (numWord = 0; numWord < size; numWord++) {
//		NORFLASH_WriteWord(startAddress + numWord, numWord);
//	}
//	SerialSendBytes("Memory written.\r\n", 17);

	char testLine[24] = "Addr:xxxxxxxx :  yyyy \r\n";
	for (numWord = 0; numWord < size; numWord++) {
		check = NORFLASH_ReadWord(startAddress + numWord);
		getHexFromLong(testLine + 5, startAddress + numWord, 8);
		getHexFromLong(testLine + 17, check, 4);
		Delay_ms(1);
		SerialSendBytes(testLine, 24);
	}

	return 0;
}

開發者ID:stm32f4，項目名稱:hy32-stm32f4，代碼行數:30，代碼來源:main.c

示例9: Init_MCU

/**************************************************************************************************
* Init MCU
**************************************************************************************************/
void Init_MCU() {

  // Set PORTB8/7 to Open Drain output mode
  GPIO_Config(&GPIOB_BASE, _GPIO_PINMASK_8, _GPIO_CFG_SPEED_50MHZ | _GPIO_CFG_OTYPE_OD | _GPIO_CFG_MODE_OUTPUT);
  GPIO_Config(&GPIOB_BASE, _GPIO_PINMASK_7, _GPIO_CFG_SPEED_50MHZ | _GPIO_CFG_OTYPE_OD | _GPIO_CFG_MODE_OUTPUT);

  GPIO_Digital_Output(&GPIOD_ODR, _GPIO_PINMASK_12);                            // LED GREEN
  GPIO_Digital_Output(&GPIOD_ODR, _GPIO_PINMASK_13);                            // LED ORANGE
  GPIO_Digital_Output(&GPIOD_ODR, _GPIO_PINMASK_14);                            // LED RED
  GPIO_Digital_Output(&GPIOD_BASE, _GPIO_PINMASK_15);                           // LED BLUE
  GPIO_Digital_Output(&GPIOC_ODR, _GPIO_PINMASK_5);                             // RF_STB
  GPIO_Digital_Output(&GPIOE_ODR, _GPIO_PINMASK_4);                             // RF_RST
  GPIO_Digital_Output(&GPIOA_IDR, _GPIO_PINMASK_0);                             // Button

  GPIO_Alternate_Function_Enable(&_GPIO_MODULE_USART2_PA23);
  UART2_Init_Advanced(19200, _UART_8_BIT_DATA, _UART_NOPARITY, _UART_ONE_STOPBIT, &_GPIO_MODULE_USART2_PA23);
  //****************************************************************************
/*UART3_Init_Advanced(9600, _UART_8_BIT_DATA, _UART_NOPARITY, _UART_ONE_STOPBIT, &_GPIO_MODULE_USART3_PB10_11);
  Delay_ms(100);
  USART3_CR1bits.RXNEIE = 1;       // enable uart rx interrupt
  NVIC_IntEnable(IVT_INT_USART3);  // enable interrupt vector
  Delay_ms(100);                        // Wait for UART module to stabilize*/
  //****************************************************************************
  UART6_Init_Advanced(19200, _UART_8_BIT_DATA, _UART_NOPARITY, _UART_ONE_STOPBIT, &_GPIO_MODULE_USART6_PC67 );
  Delay_ms(100);
  
  // Enable Usart Receiver interrupt:
  USART6_CR1bits.RXNEIE = 1;         // enable uart rx interrupt
  NVIC_IntEnable(IVT_INT_USART6);    // enable interrupt vector
  Enableinterrupts();
}

開發者ID:DAA-Tech，項目名稱:Tea-Brew-Hack-TX-Firmware，代碼行數:34，代碼來源:SHT11_click.c

示例10: darVuelta

/* Funcion usada en modo automatico para esquivar obstaculo */
void darVuelta(){
girarDerecha();
avanzarVehiculo();
Delay_ms(1000);
girarIzquierda();
avanzarVehiculo();
}

開發者ID:PinkFLoyd92，項目名稱:MicroControllers-RemoteCar，代碼行數:8，代碼來源:auto.c

示例11: CC2500_Reset

void CC2500_Reset(void)
{
	CC2500_SendSpiData(CCxxx0_SIDLE);

	Delay_ms(20);

	CC2500_Select();

	Delay_ms(20);

	CC2500_NoSelect();

	Delay_ms(40);

	CC2500_SendSpiData(CCxxx0_SRES);
}

開發者ID:sytuxww，項目名稱:q-sys，代碼行數:16，代碼來源:CC2500.c

示例12: SF_mem

void SF_mem()
{
  unsigned char i,l,cnt[4];
  long adr=0x111111;

  for(i=0;i<6;i++) {
    SerialFlash_WriteByte(arm[i],adr);
    adr+=0x000020;
  }

  strcpy(Label24.Caption,"  ******");
  DrawScreen(&System_Log_Screen);
  for(l=0;l<10;l++) {
    ByteToStr(10-l,cnt);
    strcpy(Label25.Caption,"      ");
    strcat(Label25.Caption,cnt);
    DrawScreen(&System_Log_Screen);
    FT812_Sound_SetAndPlay(_FT812_SOUND_CLICK,_FT812_SOUND_PITCH_B3,vol);
    Delay_ms(1000);
  }
  Box30.Color=0x00FF0000;
  Box36.Color=0x00FF0000;
  Image65.Visible=0;
  Image66.Visible=1;
  strcpy(Label25.Caption,"   ARMED");
  strcpy(Label8.Caption,"   ARMED");
}

開發者ID:MikroElektronika，項目名稱:mikromedia_HMI，代碼行數:27，代碼來源:Mikromedia_HMI_70C_Demo_main.c

示例13: LCD_ExitSleep

//LCD退出休眠狀態
void LCD_ExitSleep()	//_ILI9340C(void)
{
  LCD_WRITE_CMD(0x11);//Exit Sleep
  Delay_ms(120);
  LCD_WRITE_CMD(0x29);//Display on
  LCD_WRITE_CMD(0x2c); 
}

開發者ID:weifengdq，項目名稱:MusiBoard，代碼行數:8，代碼來源:lcd.c

示例14: KeyDown_Ex

/**
* @brief	獲取按鍵是否按下
* @param	GPIOx 按鍵端口組
* @param	kpin  端口引腳
* @retval\n	0表示沒有按下否則返回按下的時間（ms）
* @remarks 是KeyDown的擴展功能，能返回該按鍵長按的時間（ms），
*		最長時間為500ms。當一個按鍵有按下、長按若幹S時用它實現
*/
int16_t KeyDown_Ex(GPIO_TypeDef* GPIOx,uint16_t kpin)
{
	static GPIO_TypeDef* oldGPIOx = 0;
	static uint16_t oldkpin = 0;
	uint16_t i;
	
// 	if(kpin == 0 && GPIOx == 0) {
// 		oldGPIOx = 0;
// 		oldkpin = 0;
// 		return 1;
// 	}
// 	if(oldGPIOx == GPIOx && oldkpin == kpin) {
// 		if(GPIO_ReadInputDataBit(GPIOx,kpin) == Key_Signal) {
// 			return 0;
// 		}
// 		else {
// 			oldGPIOx = 0;
// 			oldkpin = 0;
// 		}
// 	}
	//if((GPIOx->IDR & kpin) == 0) {

	i = 0;
	while(i < 500 && GPIO_ReadInputDataBit(GPIOx,kpin) == Key_Signal) {
		Delay_ms(10);
		i+= 10;
	}
	return i;
}

開發者ID:MenglongWu，項目名稱:uTLaser，代碼行數:37，代碼來源:key.c

示例15: main

int main(void)
{
    uint8_t i;
    uint8_t tri_table[] = {                     // triangular wave data table
        0x80, 0x84, 0x88, 0x8C, 0x90, 0x94, 0x98, 0x9C, 0xA0, 0xA4,
        0xA8, 0xAC, 0xB0, 0xB4, 0xB8, 0xBC, 0xC0, 0xC4, 0xC8, 0xCC,
        0xD0, 0xD4, 0xD8, 0xDC, 0xE0, 0xE4, 0xE0, 0xDC, 0xD8, 0xD4,
        0xD0, 0xCC, 0xC8, 0xC4, 0xC0, 0xBC, 0xB8, 0xB4, 0xB0, 0xAC,
        0xA8, 0xA4, 0xA0, 0x9C, 0x98, 0x94, 0x90, 0x8C, 0x88, 0x84,
        0x80, 0x7C, 0x78, 0x74, 0x70, 0x6C, 0x68, 0x64, 0x60, 0x5C,
        0x58, 0x54, 0x50, 0x4C, 0x48, 0x44, 0x40, 0x3C, 0x38, 0x34,
        0x30, 0x2C, 0x28, 0x24, 0x20, 0x1C, 0x20, 0x24, 0x28, 0x2C,
        0x30, 0x34, 0x38, 0x3C, 0x40, 0x44, 0x48, 0x4C, 0x50, 0x54,
        0x58, 0x5C, 0x60, 0x64, 0x68, 0x6C, 0x70, 0x74, 0x78, 0x7C
    };

    MCU_initialize();                           // initialize MCU
    Delay_ms(50);                               // wait for system stabilization
    LCD_initialize();                           // initialize text LCD module

    LCD_string(0x80, "  DAC0800 D/A   ");       // display title
    LCD_string(0xC0, "Triangular Wave ");

    while (1) {
        for (i = 0; i < 100; i++) {             // output D/A
            PORTB = tri_table[i];
            Delay_us(10);
        }
    }

    return 0;
}

開發者ID:neoelec，項目名稱:ok128c，代碼行數:32，代碼來源:Exp09_1.c

注：本文中的Delay_ms函數示例由純淨天空整理自Github/MSDocs等開源代碼及文檔管理平台，相關代碼片段篩選自各路編程大神貢獻的開源項目，源碼版權歸原作者所有，傳播和使用請參考對應項目的License；未經允許，請勿轉載。