當前位置: 首頁>>代碼示例>>C++>>正文

C++ Bot_Abort函數代碼示例

本文整理匯總了C++中Bot_Abort函數的典型用法代碼示例。如果您正苦於以下問題：C++ Bot_Abort函數的具體用法？C++ Bot_Abort怎麽用？C++ Bot_Abort使用的例子？那麽, 這裏精選的函數代碼示例或許可以為您提供幫助。


在下文中一共展示了Bot_Abort函數的15個代碼示例，這些例子默認根據受歡迎程度排序。您可以為喜歡或者感覺有用的代碼點讚，您的評價將有助於係統推薦出更棒的C++代碼示例。

示例1: Mass_Storage_Out

/*******************************************************************************
* Function Name  : Mass_Storage_Out
* Description    : Mass Storage OUT transfer.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void Mass_Storage_Out (void)
{
  u8 CMD;
  CMD = CBW.CB[0];
  Data_Len = GetEPRxCount(ENDP2);

  PMAToUserBufferCopy(Bulk_Data_Buff, ENDP2_RXADDR, Data_Len);

  switch (Bot_State)
  {
    case BOT_IDLE:
      CBW_Decode();
      break;
    case BOT_DATA_OUT:
      if (CMD == SCSI_WRITE10)
      {
        SCSI_Write10_Cmd(SCSI_LBA , SCSI_BlkLen);
        break;
      }
      Bot_Abort(DIR_OUT);
      Set_Scsi_Sense_Data(ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
      Set_CSW (CSW_PHASE_ERROR, SEND_CSW_DISABLE);
      break;
    default:
      Bot_Abort(BOTH_DIR);
      Set_Scsi_Sense_Data(ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
      Set_CSW (CSW_PHASE_ERROR, SEND_CSW_DISABLE);
      break;
  }
}
開發者ID:matthiasbock，項目名稱:DSOQuad_SourceCode，代碼行數:37，代碼來源:USB_bot.c

示例2: Mass_Storage_Out

/*******************************************************************************
* Function Name  : Mass_Storage_Out
* Description    : Mass Storage OUT transfer.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void Mass_Storage_Out (void)
{
  uint8_t CMD;
  CMD = CBW.CB[0];

  Data_Len = USB_SIL_Read(EP5_OUT, Bulk_Data_Buff);

  switch (Bot_State)
  {
    case BOT_IDLE:
      CBW_Decode();
      break;
    case BOT_DATA_OUT:
      if (CMD == SCSI_WRITE10)
      {
        SCSI_Write10_Cmd(CBW.bLUN , SCSI_LBA , SCSI_BlkLen);
        break;
      }
      Bot_Abort(DIR_OUT);
      Set_Scsi_Sense_Data(CBW.bLUN, ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
      Set_CSW (CSW_PHASE_ERROR, SEND_CSW_DISABLE);
      break;
    default:
      Bot_Abort(BOTH_DIR);
      Set_Scsi_Sense_Data(CBW.bLUN, ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
      Set_CSW (CSW_PHASE_ERROR, SEND_CSW_DISABLE);
      break;
  }

  //az
#ifndef STM32F10X_CL
  /* Enable the receive of data on EP3 */
  SetEPRxValid(ENDP5);
#endif /* STM32F10X_CL */
}
開發者ID:AndrewZamansky，項目名稱:uCProjects，代碼行數:42，代碼來源:usb_bot.c

示例3: SCSI_Address_Management

/*******************************************************************************
* Function Name  : SCSI_Address_Management
* Description    : Test the received address.
* Input          : u8 Cmd : the command can be SCSI_READ10 or SCSI_WRITE10.
* Output         : None.
* Return         : Read\Write status (bool).
*******************************************************************************/
bool SCSI_Address_Management(u8 Cmd , u32 LBA , u32 BlockNbr)
{

  if ((LBA + BlockNbr) > Mass_Block_Count )
  {
    if (Cmd == SCSI_WRITE10)
    {
      Bot_Abort(BOTH_DIR);
    }
    Bot_Abort(DIR_IN);
    Set_Scsi_Sense_Data(ILLEGAL_REQUEST, ADDRESS_OUT_OF_RANGE);
    Set_CSW (CSW_CMD_FAILED, SEND_CSW_DISABLE);
    return false;
  }


  if (CBW.dDataLength != BlockNbr * Mass_Block_Size)
  {
    if (Cmd == SCSI_WRITE10)
    {
      Bot_Abort(BOTH_DIR);
    }
    else
    {
      Bot_Abort(DIR_IN);
    }
    Set_Scsi_Sense_Data(ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
    Set_CSW (CSW_CMD_FAILED, SEND_CSW_DISABLE);
    return false;
  }
  return true;
}
開發者ID:PetteriAimonen，項目名稱:dsoquad-BIOS，代碼行數:39，代碼來源:USB_scsi.c

示例4: Mass_Storage_Out

/*******************************************************************************
* Function Name  : Mass_Storage_Out
* Description    : Mass Storage OUT transfer.
* Input          : None.
* Output         : None.
* Return         : None.
//USB->設備
*******************************************************************************/
void Mass_Storage_Out (void)
{
	u8 CMD;
	USB_STATUS_REG|=0X10;//標記輪詢
	
	CMD = CBW.CB[0];
	Data_Len = GetEPRxCount(ENDP4);
	PMAToUserBufferCopy(Bulk_Data_Buff, ENDP4_RXADDR, Data_Len);
//printf("Bot_State_out:%d;Data_Len=%d",Bot_State,Data_Len);
	switch (Bot_State)
	{
		case BOT_IDLE:
			CBW_Decode();
			break;
		case BOT_DATA_OUT://USB發送數據到設備
			if (CMD == SCSI_WRITE10)
			{
				USB_STATUS_REG|=0X01;//標記正在寫數據
				SCSI_Write10_Cmd(CBW.bLUN , SCSI_LBA , SCSI_BlkLen);
				break;
			}
			Bot_Abort(DIR_OUT);
			Set_Scsi_Sense_Data(CBW.bLUN, ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
			Set_CSW (CSW_PHASE_ERROR, SEND_CSW_DISABLE);
			break;
		default:
			Bot_Abort(BOTH_DIR);
			Set_Scsi_Sense_Data(CBW.bLUN, ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
			Set_CSW (CSW_PHASE_ERROR, SEND_CSW_DISABLE);
			break;
	}
}
開發者ID:blackmiaool，項目名稱:cattyware，代碼行數:40，代碼來源:usb_bot.c

示例5: SCSI_Address_Management

/*******************************************************************************
* Function Name  : SCSI_Address_Management
* Description    : Test the received address.
* Input          : uint8_t Cmd : the command can be SCSI_READ10 or SCSI_WRITE10.
* Output         : None.
* Return         : Read\Write status (bool).
*******************************************************************************/
bool SCSI_Address_Management(uint8_t lun , uint8_t Cmd , uint32_t LBA , uint32_t BlockNbr)
{

  if ((LBA + BlockNbr) > Mass_Block_Count[lun] )
  {
    if (Cmd == SCSI_WRITE10)
    {
      Bot_Abort(BOTH_DIR);
    }
    Bot_Abort(DIR_IN);
    Set_Scsi_Sense_Data(lun, ILLEGAL_REQUEST, ADDRESS_OUT_OF_RANGE);
    Set_CSW (CSW_CMD_FAILED, SEND_CSW_DISABLE);
    return (FALSE);
  }


  if (CBW.dDataLength != BlockNbr * Mass_Block_Size[lun])
  {
    if (Cmd == SCSI_WRITE10)
    {
      Bot_Abort(BOTH_DIR);
    }
    else
    {
      Bot_Abort(DIR_IN);
    }
    Set_Scsi_Sense_Data(CBW.bLUN, ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
    Set_CSW (CSW_CMD_FAILED, SEND_CSW_DISABLE);
    return (FALSE);
  }
  return (TRUE);
}
開發者ID:crystalfontz，項目名稱:cfa_735_simple，代碼行數:39，代碼來源:usb_scsi.c

示例6: Mass_Storage_Out

/*******************************************************************************
* Function Name  : Mass_Storage_Out
* Description    : Mass Storage OUT transfer.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void Mass_Storage_Out (void)
{
  u8 CMD;
  CMD = CBW.CB[0];

  Data_Len = USB_SIL_Read(EP2_OUT, Bulk_Data_Buff);

  switch (Bot_State)
  {
    case BOT_IDLE:
      CBW_Decode();
      break;
    case BOT_DATA_OUT:
      if (CMD == SCSI_WRITE10)
      {
        SCSI_Write10_Cmd(CBW.bLUN , SCSI_LBA , SCSI_BlkLen);
        break;
      }
      Bot_Abort(DIR_OUT);
      Set_Scsi_Sense_Data(CBW.bLUN, ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
      Set_CSW (CSW_PHASE_ERROR, SEND_CSW_DISABLE);
      break;
    default:
      Bot_Abort(BOTH_DIR);
      Set_Scsi_Sense_Data(CBW.bLUN, ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
      Set_CSW (CSW_PHASE_ERROR, SEND_CSW_DISABLE);
      break;
  }
}
開發者ID:joe3501，項目名稱:BlueRing，代碼行數:36，代碼來源:usb_bot.c

示例7: SCSI_Write10_Cmd

/*******************************************************************************
* Function Name  : SCSI_Write10_Cmd
* Description    : SCSI Write10 Command routine.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void SCSI_Write10_Cmd(u32 LBA , u32 BlockNbr)
{

  if (Bot_State == BOT_IDLE)
  {
    if (!(SCSI_Address_Management(SCSI_WRITE10 , LBA, BlockNbr)))/*address out of range*/
    {
      return;
    }

    if ((CBW.bmFlags & 0x80) == 0)
    {
      Bot_State = BOT_DATA_OUT;
      SetEPRxStatus(ENDP2, EP_RX_VALID);
    }
    else
    {
      Bot_Abort(DIR_IN);
      Set_Scsi_Sense_Data(ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
      Set_CSW (CSW_CMD_FAILED, SEND_CSW_DISABLE);
    }
    return;
  }
  else if (Bot_State == BOT_DATA_OUT)
  {
    Write_Memory(LBA , BlockNbr);
  }
}
開發者ID:PetteriAimonen，項目名稱:dsoquad-BIOS，代碼行數:35，代碼來源:USB_scsi.c

示例8: SCSI_Write10_Cmd

/*******************************************************************************
* Function Name  : SCSI_Write10_Cmd
* Description    : SCSI Write10 Command routine.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void SCSI_Write10_Cmd(uint8_t lun , uint32_t LBA , uint32_t BlockNbr)
{

  if (Bot_State == BOT_IDLE)
  {
    if (!(SCSI_Address_Management(CBW.bLUN, SCSI_WRITE10 , LBA, BlockNbr)))/*address out of range*/
    {
      return;
    }

    if ((CBW.bmFlags & 0x80) == 0)
    {
      Bot_State = BOT_DATA_OUT;
    #ifndef STM32F10X_CL
      SetEPRxStatus(ENDP2, EP_RX_VALID);
    #endif /* STM32F10X_CL */
    }
    else
    {
      Bot_Abort(DIR_IN);
      Set_Scsi_Sense_Data(CBW.bLUN, ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
      Set_CSW (CSW_CMD_FAILED, SEND_CSW_DISABLE);
    }
    return;
  }
  else if (Bot_State == BOT_DATA_OUT)
  {
    Write_Memory(lun , LBA , BlockNbr);
  }
}
開發者ID:crystalfontz，項目名稱:cfa_735_simple，代碼行數:37，代碼來源:usb_scsi.c

示例9: SCSI_Read10_Cmd

/*******************************************************************************
* Function Name  : SCSI_Read10_Cmd
* Description    : SCSI Read10 Command routine.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void SCSI_Read10_Cmd(uint8_t lun , uint32_t LBA , uint32_t BlockNbr)
{

  if (Bot_State == BOT_IDLE)
  {
    if (!(SCSI_Address_Management(CBW.bLUN, SCSI_READ10, LBA, BlockNbr)))/*address out of range*/
    {
      return;
    }

    if ((CBW.bmFlags & 0x80) != 0)
    {
      Bot_State = BOT_DATA_IN;
      Read_Memory(lun, LBA , BlockNbr);
    }
    else
    {
      Bot_Abort(BOTH_DIR);
      Set_Scsi_Sense_Data(CBW.bLUN, ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
      Set_CSW (CSW_CMD_FAILED, SEND_CSW_ENABLE);
    }
    return;
  }
  else if (Bot_State == BOT_DATA_IN)
  {
    Read_Memory(lun , LBA , BlockNbr);
  }
}
開發者ID:crystalfontz，項目名稱:cfa_735_simple，代碼行數:35，代碼來源:usb_scsi.c

示例10: Mass_Storage_ClearFeature

/*******************************************************************************
* Function Name  : Mass_Storage_ClearFeature
* Description    : Handle the ClearFeature request.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void Mass_Storage_ClearFeature(void)
{
  /* when the host send a CBW with invalid signature or invalid length the two
     Endpoints (IN & OUT) shall stall until receiving a Mass Storage Reset     */
  if (CBW.dSignature != BOT_CBW_SIGNATURE)
    Bot_Abort(BOTH_DIR);
}
開發者ID:a-c-t-i-n-i-u-m，項目名稱:HY-STM32F103，代碼行數:14，代碼來源:usb_prop.c

示例11: Address_Management_Test

/*******************************************************************************
* Function Name  : Address_Management_Test
* Description    : Test the received address. 
* Input          : u8 Cmd : the command can be SCSI_READ10 or SCSI_WRITE10.
* Output         : None.
* Return         : Read\Write status (bool).
*******************************************************************************/
bool Address_Management_Test(u8 Cmd)
{
  vu32 temp1;
  vu32 temp2;
  GPIO_SetBits(GPIOB, GPIO_Pin_5);
  /* Logical Block Address of First Block */
  temp1 = (CBW.CB[2] << 24) |
          (CBW.CB[3] << 16) |
          (CBW.CB[4] <<  8) |
          (CBW.CB[5] <<  0);
  /* Number of Blocks to transfer */
  temp2 = (CBW.CB[7] <<  8) |
          (CBW.CB[8] <<  0);

  Memory_Offset = temp1 * Mass_Block_Size;
  Transfer_Length = temp2 * Mass_Block_Size;

  if ((Memory_Offset + Transfer_Length) > Mass_Memory_Size)
  {
    if (Cmd == SCSI_WRITE10)
    {
      Bot_Abort(BOTH_DIR);
    }
    Bot_Abort(DIR_IN);
    Set_Scsi_Sense_Data(ILLEGAL_REQUEST, ADDRESS_OUT_OF_RANGE);
    Set_CSW (CSW_CMD_FAILED, SEND_CSW_DISABLE);
    return (FALSE);
  }


  if (CBW.dDataLength != Transfer_Length)
  {
    if (Cmd == SCSI_WRITE10)
    {
      Bot_Abort(BOTH_DIR);
    }
    else
    {
      Bot_Abort(DIR_IN);
    }
    Set_Scsi_Sense_Data(ILLEGAL_REQUEST, INVALID_FIELED_IN_COMMAND);
    Set_CSW (CSW_CMD_FAILED, SEND_CSW_DISABLE);
    return (FALSE);
  }
  return (TRUE);
}
開發者ID:HamsterReserved，項目名稱:STM32-NAND-Programmer，代碼行數:53，代碼來源:memory.c

示例12: SCSI_Format_Cmd

/*******************************************************************************
* Function Name  : SCSI_Format_Cmd
* Description    : Format Commands routine.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void SCSI_Format_Cmd(uint8_t lun)
{
  if (MAL_GetStatus(lun))
  {
    Set_Scsi_Sense_Data(CBW.bLUN, NOT_READY, MEDIUM_NOT_PRESENT);
    Set_CSW (CSW_CMD_FAILED, SEND_CSW_ENABLE);
    Bot_Abort(DIR_IN);
    return;
  }
}
開發者ID:MBARM，項目名稱:MatchboxARM，代碼行數:17，代碼來源:usb_scsi.c

示例13: SCSI_Invalid_Cmd

/*******************************************************************************
* Function Name  : SCSI_Invalid_Cmd
* Description    : Invalid Commands routine
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void SCSI_Invalid_Cmd(uint8_t lun)
{
  if (CBW.dDataLength == 0)
  {
    Bot_Abort(DIR_IN);
  }
  else
  {
    if ((CBW.bmFlags & 0x80) != 0)
    {
      Bot_Abort(DIR_IN);
    }
    else
    {
      Bot_Abort(BOTH_DIR);
    }
  }
  Set_Scsi_Sense_Data(CBW.bLUN, ILLEGAL_REQUEST, INVALID_COMMAND);
  Set_CSW (CSW_CMD_FAILED, SEND_CSW_DISABLE);
}
開發者ID:crystalfontz，項目名稱:cfa_735_simple，代碼行數:27，代碼來源:usb_scsi.c

示例14: SCSI_Valid_Cmd

/*******************************************************************************
* Function Name  : SCSI_Valid_Cmd
* Description    : Valid Commands routine.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void SCSI_Valid_Cmd(uint8_t lun)
{
  if (CBW.dDataLength != 0)
  {
    Bot_Abort(BOTH_DIR);
    Set_Scsi_Sense_Data(CBW.bLUN, ILLEGAL_REQUEST, INVALID_COMMAND);
    Set_CSW (CSW_CMD_FAILED, SEND_CSW_DISABLE);
  }
  else
    Set_CSW (CSW_CMD_PASSED, SEND_CSW_ENABLE);
}
開發者ID:crystalfontz，項目名稱:cfa_735_simple，代碼行數:18，代碼來源:usb_scsi.c

示例15: USB_APP_ClearFeature

/*******************************************************************************
* Function Name  : Mass_Storage_ClearFeature
* Description    : Handle the ClearFeature request.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void USB_APP_ClearFeature(void)
{
#if(USB_DEVICE_CONFIG & _USE_USB_MASS_STOARGE_DEVICE)
	/* when the host send a CBW with invalid signature or invalid length the two
	Endpoints (IN & OUT) shall stall until receiving a Mass Storage Reset     */
	if (g_usb_type == USB_MASSSTORAGE)
	{
		if (CBW.dSignature != BOT_CBW_SIGNATURE)
			Bot_Abort(BOTH_DIR);
	}
#endif

}
開發者ID:joe3501，項目名稱:BTPrinter，代碼行數:20，代碼來源:usb_prop.c


注：本文中的Bot_Abort函數示例由純淨天空整理自Github/MSDocs等開源代碼及文檔管理平台，相關代碼片段篩選自各路編程大神貢獻的開源項目，源碼版權歸原作者所有，傳播和使用請參考對應項目的License；未經允許，請勿轉載。