C++ BSP_LCD_Init函數代碼示例

本文整理匯總了C++中BSP_LCD_Init函數的典型用法代碼示例。如果您正苦於以下問題：C++ BSP_LCD_Init函數的具體用法？C++ BSP_LCD_Init怎麽用？C++ BSP_LCD_Init使用的例子？那麽, 這裏精選的函數代碼示例或許可以為您提供幫助。

在下文中一共展示了BSP_LCD_Init函數的15個代碼示例，這些例子默認根據受歡迎程度排序。您可以為喜歡或者感覺有用的代碼點讚，您的評價將有助於係統推薦出更棒的C++代碼示例。

示例1: DynamicSwitch_InitApplication

/**
  * @brief  DS application Init.
  * @param  None
  * @retval None
  */
static void DynamicSwitch_InitApplication(void)
{
  /* Configure Key Button */
  BSP_PB_Init(BUTTON_TAMPER, BUTTON_MODE_GPIO);                 
  
  /* Configure LED1 */
  BSP_LED_Init(LED1);
  
  /* Initialize the LCD */
  BSP_LCD_Init();
  
  /* LCD Layer Initialization */
  BSP_LCD_LayerDefaultInit(1, LCD_FB_START_ADDRESS); 
  
  /* Selects the LCD Layer */
  BSP_LCD_SelectLayer(1);
  
  /* Enables the display */
  BSP_LCD_DisplayOn();
  
  /* Init the LCD Log module */
  LCD_LOG_Init();
  
#ifdef USE_USB_HS 
  LCD_LOG_SetHeader((uint8_t *)" USB HS DynamicSwitch Host");
#else
  LCD_LOG_SetHeader((uint8_t *)" USB FS DynamicSwitch Host");
#endif
  
  LCD_UsrLog("USB Host library started.\n"); 
  
  /* Start Dynamic Switch Interface */
  LCD_UsrLog("Starting DynamicSwitch Demo\n");
  LCD_UsrLog("Plug your device To Continue...\n");
}

開發者ID:RadMie，項目名稱:STM32F7DiscoveryBase，代碼行數:40，代碼來源:main.c

示例2: LCD_Config

/**
  * @brief  LCD configuration
  * @param  None
  * @retval None
  */
static void LCD_Config(void)
{
  /* LCD Initialization */ 
  /* Two layers are used in this application but not simultaneously 
     so "LCD_MAX_PCLK" is recommended to programme the maximum PCLK = 25,16 MHz */
  BSP_LCD_Init();

  /* LCD Initialization */ 
  BSP_LCD_LayerDefaultInit(0, LCD_FB_START_ADDRESS);
  BSP_LCD_LayerDefaultInit(1, LCD_FB_START_ADDRESS+(BSP_LCD_GetXSize()*BSP_LCD_GetYSize()*4));

  /* Enable the LCD */ 
  BSP_LCD_DisplayOn(); 
  
  /* Select the LCD Background Layer  */
  BSP_LCD_SelectLayer(0);

  /* Clear the Background Layer */ 
  BSP_LCD_Clear(LCD_COLOR_BLACK);  
  
  /* Select the LCD Foreground Layer  */
  BSP_LCD_SelectLayer(1);

  /* Clear the Foreground Layer */ 
  BSP_LCD_Clear(LCD_COLOR_BLACK);
  
  /* Configure the transparency for foreground and background :
     Increase the transparency */
  BSP_LCD_SetTransparency(0, 0);
  BSP_LCD_SetTransparency(1, 100);
}

開發者ID:acrepina，項目名稱:STM32F7_serverWEB，代碼行數:36，代碼來源:main.c

示例3: CDC_InitApplication

/**
  * @brief  CDC application Init
  * @param  None
  * @retval None
  */
static void CDC_InitApplication(void)
{
  /* Configure LED1, LED2, LED3 and LED4 */
  BSP_LED_Init(LED1);
  BSP_LED_Init(LED2);
  BSP_LED_Init(LED3);
  BSP_LED_Init(LED4);
  
  /* Configure KEY Button */
  BSP_PB_Init(BUTTON_WAKEUP, BUTTON_MODE_GPIO);
  
  /* Initialize the LCD */
  BSP_LCD_Init();
  BSP_LCD_LayerDefaultInit(0, LCD_FB_START_ADDRESS);
  BSP_LCD_SelectLayer(0);
  
  /* Init the LCD Log module */
  LCD_LOG_Init();
  
  LCD_LOG_SetHeader((uint8_t *)" USB OTG FS CDC Host");
  LCD_UsrLog("USB Host library started.\n"); 
    
  /* Start CDC Interface */
  USBH_UsrLog("Starting CDC Demo");
  
  Menu_Init();
}

開發者ID:pierreroth64，項目名稱:STM32Cube_FW_F4，代碼行數:32，代碼來源:main.c

示例4: BSP_Init

/*-------------------------------------------------------
功能	: 初始化
輸入	: void
返回	: void
Copyright : yitiandelan.
---------------------------------------------------------*/
void BSP_Init(void)
{
	BSP_OSC_Init();
	
	#if (configUSE_LED == 1)
	BSP_LED_Init();
	#endif
	#if (configUSE_DAC == 1)
	BSP_DAC_Init();
	#endif
	#if (configUSE_ADC123 == 1)
	BSP_ADC_Init();
	#endif
	#if (configUSE_ExternADC == 1)
	BSP_ADC_ex_Init();
	#endif
	#if (configUSE_LCD == 1)
	BSP_LCD_Init();
	#endif
	#if (configUSE_CODEC == 1)
	BSP_CODEC_Init();
	#endif
	#if (configUSE_PWM == 1)
	BSP_TIM3_Init();
	#endif
	#if (configUSE_RTT == 1)
	BSP_RTT_Init();
	#endif
	#if (configUSE_USB == 1)
	BSP_USB_Init();
	#endif
	#if (configUSE_MPU == 1)
	BSP_MPU_Init();
	#endif
}

開發者ID:yitiandelan，項目名稱:MyF4Project，代碼行數:41，代碼來源:BSP.c

示例5: HID_InitApplication

/**
  * @brief  HID application Init.
  * @param  None
  * @retval None
  */
static void HID_InitApplication(void)
{
  /* Configure Key Button */
  BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);                
  
  /* Configure Joystick in EXTI mode */
  BSP_JOY_Init(JOY_MODE_EXTI);
  
  /* Configure LED1, LED2, LED3 and LED4 */
  BSP_LED_Init(LED1);
  BSP_LED_Init(LED2);
  BSP_LED_Init(LED3);
  BSP_LED_Init(LED4);
  
  /* Initialize the LCD */
  BSP_LCD_Init();
  
  /* Initialize the LCD Log module */
  LCD_LOG_Init();
  
#ifdef USE_USB_HS 
  LCD_LOG_SetHeader((uint8_t *)" USB OTG HS HID Host");
#else
  LCD_LOG_SetHeader((uint8_t *)" USB OTG FS HID Host");
#endif
  
  LCD_UsrLog("USB Host library started.\n"); 
  
  /* Start HID Interface */
  USBH_UsrLog("Starting HID Demo");
  HID_MenuInit();
}

開發者ID:PaxInstruments，項目名稱:STM32CubeF2，代碼行數:37，代碼來源:main.c

示例6: DynamicSwitch_InitApplication

/**
  * @brief  DS application Init.
  * @param  None
  * @retval None
  */
static void DynamicSwitch_InitApplication(void)
{
    /* Configure Key Button */
    BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_EXTI);

    /* Configure Joystick in EXTI mode */
    BSP_JOY_Init(JOY_MODE_EXTI);

    /* Configure LED1, LED2, LED3 and LED4 */
    BSP_LED_Init(LED1);
    BSP_LED_Init(LED2);
    BSP_LED_Init(LED3);
    BSP_LED_Init(LED4);

    /* Initialize the LCD */
    BSP_LCD_Init();

    /* Initialize the LCD Log module */
    LCD_LOG_Init();

#ifdef USE_USB_HS
    LCD_LOG_SetHeader((uint8_t *)" USB HS DynamicSwitch Host");
#else
    LCD_LOG_SetHeader((uint8_t *)" USB FS DynamicSwitch Host");
#endif

    LCD_UsrLog("USB Host library started.\n");

    /* Start Dynamic Switch Interface */
    LCD_UsrLog("Starting DynamicSwitch Demo\n");
    LCD_UsrLog("Plug your device To Continue...\n");
}

開發者ID:PaxInstruments，項目名稱:STM32CubeF4，代碼行數:37，代碼來源:main.c

示例7: DUAL_InitApplication

/**
  * @brief  DUALCORE application Init.
  * @param  None
  * @retval None
  */
static void DUAL_InitApplication(void)
{
  /* Configure Key Button */
  BSP_PB_Init(BUTTON_TAMPER, BUTTON_MODE_GPIO);                
  
  /* Configure LED1 */
  BSP_LED_Init(LED1);
  
  /* Initialize the LCD */
  BSP_LCD_Init();
  
  /* LCD Layer Initialization */
  BSP_LCD_LayerDefaultInit(1, LCD_FB_START_ADDRESS); 
  
  /* Selects the LCD Layer */
  BSP_LCD_SelectLayer(1);
  
  /* Enables the display */
  BSP_LCD_DisplayOn();
  
  /* Init the LCD Log module */
  LCD_LOG_Init();
  
  LCD_LOG_SetHeader((uint8_t *)" USB OTG DualCore Host");
  
  LCD_UsrLog("USB Host library started.\n"); 
  
  /* Start DualCore Interface */
  USBH_UsrLog("Initializing hardware....");
  DUAL_MenuInit(); 
}

開發者ID:acrepina，項目名稱:STM32F7_serverWEB，代碼行數:36，代碼來源:main.c

示例8: Display_Init

/**
  * @brief  Display Init (LCD)
  * @param  None
  * @retval None
  */
static void Display_Init(void)
{
  /* Initialize the LCD */
  BSP_LCD_Init();

  /* Clear the LCD */ 
  BSP_LCD_Clear(LCD_COLOR_WHITE);
  
  /* Set LCD Demo description */
  BSP_LCD_SetTextColor(LCD_COLOR_BLUE);
  BSP_LCD_FillRect(0, 0, BSP_LCD_GetXSize(), 80);
  BSP_LCD_SetTextColor(LCD_COLOR_WHITE);
  BSP_LCD_SetBackColor(LCD_COLOR_BLUE); 
  BSP_LCD_SetFont(&Font24);
  BSP_LCD_DisplayStringAt(0, 0, (uint8_t*)MESSAGE1, CENTER_MODE);
  BSP_LCD_SetFont(&Font12);
  BSP_LCD_DisplayStringAt(0, 30, (uint8_t*)"ADC Low Power Mode", CENTER_MODE); 
  BSP_LCD_DisplayStringAt(0, 45, (uint8_t*)"Press Tamper push-button", CENTER_MODE); 
  BSP_LCD_DisplayStringAt(0, 60, (uint8_t*)MESSAGE3, CENTER_MODE); 

   /* Set the LCD Text Color */
  BSP_LCD_SetTextColor(LCD_COLOR_BLUE);  
  BSP_LCD_DrawRect(10, 90, BSP_LCD_GetXSize() - 20, BSP_LCD_GetYSize()- 100);
  BSP_LCD_DrawRect(11, 91, BSP_LCD_GetXSize() - 22, BSP_LCD_GetYSize()- 102);

  BSP_LCD_SetFont(&Font24);
  BSP_LCD_SetBackColor(LCD_COLOR_WHITE); 
}

開發者ID:jmoyerman，項目名稱:stm32f0_cube，代碼行數:33，代碼來源:main.c

示例9: HID_InitApplication

/**
  * @brief  HID application Init
  * @param  None
  * @retval None
  */
static void HID_InitApplication(void)
{
  /* Configure KEY Button */
  BSP_PB_Init(BUTTON_TAMPER, BUTTON_MODE_GPIO);
  
  /* Configure Joystick in EXTI mode */
  BSP_JOY_Init(JOY_MODE_EXTI);

  /* Initialize the LCD */
  BSP_LCD_Init();
  
  /* Init the LCD Log module */
  LCD_LOG_Init();
  
#ifdef USE_USB_HS 
  LCD_LOG_SetHeader((uint8_t *)" USB OTG HS HID Host");
#else
  LCD_LOG_SetHeader((uint8_t *)" USB OTG FS HID Host");
#endif
  
  LCD_UsrLog("USB Host library started.\n"); 
  
  /* Start HID Interface */
  HID_MenuInit();
}

開發者ID:pierreroth64，項目名稱:STM32Cube_FW_F4，代碼行數:30，代碼來源:main.c

示例10: HID_InitApplication

/**
  * @brief  HID application Init.
  * @param  None
  * @retval None
  */
static void HID_InitApplication(void)
{
  /* Configure Key Button */
  BSP_PB_Init(BUTTON_TAMPER, BUTTON_MODE_EXTI);
  
  /* Configure LED1*/
  BSP_LED_Init(LED1);
  
  /* Initialize the LCD */
  BSP_LCD_Init();
  
  /* LCD Layer Initialization */
  BSP_LCD_LayerDefaultInit(1, LCD_FB_START_ADDRESS); 
  
  /* Select the LCD Layer */
  BSP_LCD_SelectLayer(1);
  
  /* Enable the display */
  BSP_LCD_DisplayOn();
  
  /* Initialize the LCD Log module */
  LCD_LOG_Init();
  
#ifdef USE_USB_HS 
  LCD_LOG_SetHeader((uint8_t *)" USB OTG HS HID Host");
#else
  LCD_LOG_SetHeader((uint8_t *)" USB OTG FS HID Host");
#endif
  
  LCD_UsrLog("USB Host library started.\n"); 
  
  /* Start HID Interface */
  USBH_UsrLog("Starting HID Demo");
  HID_MenuInit();
}

開發者ID:MrZANE42，項目名稱:verisure1512，代碼行數:40，代碼來源:main.c

示例11: DUAL_InitApplication

/**
  * @brief  DUALCORE application Init.
  * @param  None
  * @retval None
  */
static void DUAL_InitApplication(void)
{
  /* Configure KEY Button */
  BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);                
  
  /* Configure Joystick in EXTI mode */
  BSP_JOY_Init(JOY_MODE_EXTI);
  
  /* Configure the LEDs */
  BSP_LED_Init(LED1);
  BSP_LED_Init(LED2);
  BSP_LED_Init(LED3);
  BSP_LED_Init(LED4);
  
  /* Initialize the LCD */
  BSP_LCD_Init();
  
  /* Initialize the LCD Log module */
  LCD_LOG_Init();
  
  LCD_LOG_SetHeader((uint8_t *)" USB OTG DualCore Host");
  
  LCD_UsrLog("USB Host library started.\n"); 
  
  /* Start DualCore Interface */
  USBH_UsrLog("Initializing hardware....");
  DUAL_MenuInit(); 
}

開發者ID:EarnestHein89，項目名稱:STM32Cube_FW_F4，代碼行數:33，代碼來源:main.c

示例12: MSC_InitApplication

/**
  * @brief  MSC application Init.
  * @param  None
  * @retval None
  */
static void MSC_InitApplication(void)
{
  /* Configure Key Button */
  BSP_PB_Init(BUTTON_WAKEUP, BUTTON_MODE_EXTI);
      
  /* Configure LED1 */
  BSP_LED_Init(LED1);
  
  /* Initialize the LCD */
  BSP_LCD_Init();
  
  /* LCD Layer Initialization */
  BSP_LCD_LayerDefaultInit(1, LCD_FB_START_ADDRESS); 
  
  /* Select the LCD Layer */
  BSP_LCD_SelectLayer(1);
  
  /* Enable the display */
  BSP_LCD_DisplayOn();
  
  /* Initialize the LCD Log module */
  LCD_LOG_Init();
  
  LCD_LOG_SetHeader((uint8_t *)" USB OTG FS MSC Host");
  LCD_UsrLog("USB Host library started.\n"); 
  
  /* Initialize menu and MSC process */
  Menu_Init();
}

開發者ID:pierreroth64，項目名稱:STM32Cube_FW_F4，代碼行數:34，代碼來源:main.c

示例13: MSC_InitApplication

/**
  * @brief  MSC application Init.
  * @param  None
  * @retval None
  */
static void MSC_InitApplication(void)
{
  /* Configure Key Button */
  BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);

  /* Configure Joystick in EXTI mode */
  BSP_JOY_Init(JOY_MODE_EXTI);

  /* Configure LED1, LED2, LED3 and LED4 */
  BSP_LED_Init(LED1);
  BSP_LED_Init(LED2);
  BSP_LED_Init(LED3);
  BSP_LED_Init(LED4);

  /* Initialize the LCD */
  BSP_LCD_Init();
  BSP_LCD_LayerDefaultInit(0, LCD_FB_START_ADDRESS);
  BSP_LCD_SelectLayer(0);

  /* Init the LCD Log module */
  LCD_LOG_Init();

#ifdef USE_USB_HS
  LCD_LOG_SetHeader((uint8_t *)" USB OTG HS MSC Host");
#else
  LCD_LOG_SetHeader((uint8_t *)" USB OTG FS MSC Host");
#endif

  LCD_UsrLog("USB Host library started.\n");

  /* Initialize menu and MSC process */
  USBH_UsrLog("Starting MSC Demo");
  Menu_Init();
}

開發者ID:Joe-Merten，項目名稱:Stm32-Tools-Evaluation，代碼行數:39，代碼來源:main.c

示例14: main

/**
  * @brief   Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F4xx HAL library initialization:
       - Configure the Flash prefetch, instruction and Data caches
       - Configure the Systick to generate an interrupt each 1 msec
       - Set NVIC Group Priority to 4
       - Global MSP (MCU Support Package) initialization
     */
  HAL_Init();

  /* Configure the system clock to 168 MHz */
  SystemClock_Config();

  /*##-1- Initialize the SRAM ################################################*/
  BSP_SRAM_Init();

  /*##-2- Initialize the LCD #################################################*/
  BSP_LCD_Init();

  /*##-3- Camera Initialization and start capture ############################*/
  /* Initialize the Camera */
  BSP_CAMERA_Init(CAMERA_R320x240);

  /* Start the Camera Capture */
  BSP_CAMERA_ContinuousStart((uint8_t *)CAMERA_FRAME_BUFFER);

  /* Infinite loop */
  while (1)
  {
  }
}

開發者ID:Joe-Merten，項目名稱:Stm32-Tools-Evaluation，代碼行數:36，代碼來源:main.c

示例15: LCD_Config

/**
  * @brief  LCD configuration.
  * @param  None
  * @retval None
  */
static void LCD_Config(void)
{
  /* LCD Initialization */ 
  BSP_LCD_Init();

  /* LCD Layers Initialization */ 
  BSP_LCD_LayerDefaultInit(0, LCD_FB_START_ADDRESS);
  BSP_LCD_LayerDefaultInit(1, (LCD_FB_START_ADDRESS+(BSP_LCD_GetXSize()*BSP_LCD_GetYSize()*4)));
  
  /* Enable the LCD */ 
  BSP_LCD_DisplayOn();

  /* Set LCD Background Layer  */
  BSP_LCD_SelectLayer(0);
  /* Clear the Background Layer */
  BSP_LCD_Clear(LCD_COLOR_WHITE);

  /* Set LCD Foreground Layer  */
  BSP_LCD_SelectLayer(1);
  /* Clear the Foreground Layer */ 
  BSP_LCD_Clear(LCD_COLOR_BLACK); 

  /* Configure and enable the Color Keying feature */
  BSP_LCD_SetColorKeying(1, 0); 

  /* Configure the transparency for foreground: Increase the transparency */
  BSP_LCD_SetTransparency(1, 100);
}

開發者ID:451506709，項目名稱:automated_machine，代碼行數:33，代碼來源:main.c

注：本文中的BSP_LCD_Init函數示例由純淨天空整理自Github/MSDocs等開源代碼及文檔管理平台，相關代碼片段篩選自各路編程大神貢獻的開源項目，源碼版權歸原作者所有，傳播和使用請參考對應項目的License；未經允許，請勿轉載。