當前位置: 首頁>>代碼示例>>C++>>正文

C++ AsicSendCommandToMcu函數代碼示例

本文整理匯總了C++中AsicSendCommandToMcu函數的典型用法代碼示例。如果您正苦於以下問題：C++ AsicSendCommandToMcu函數的具體用法？C++ AsicSendCommandToMcu怎麽用？C++ AsicSendCommandToMcu使用的例子？那麽, 這裏精選的函數代碼示例或許可以為您提供幫助。


在下文中一共展示了AsicSendCommandToMcu函數的15個代碼示例，這些例子默認根據受歡迎程度排序。您可以為喜歡或者感覺有用的代碼點讚，您的評價將有助於係統推薦出更棒的C++代碼示例。

示例1: AsicSetRxAnt

/*
 Antenna divesity use GPIO3 and EESK pin for control
 Antenna and EEPROM access are both using EESK pin,
 Therefor we should avoid accessing EESK at the same time
 Then restore antenna after EEPROM access
 The original name of this function is AsicSetRxAnt(), now change to 
*/
VOID RT30xxSetRxAnt(
	IN PRTMP_ADAPTER	pAd,
	IN UCHAR			Ant)
{
	UINT32	Value;

	if (/*(!pAd->NicConfig2.field.AntDiversity) ||*/
		(RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_RESET_IN_PROGRESS))	||
		(RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_HALT_IN_PROGRESS))	||
		(RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_RADIO_OFF)) ||
		(RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST)))
	{
		return;
	}

	/* the antenna selection is through firmware and MAC register(GPIO3) */
	if (IS_RT2070(pAd) || (IS_RT3070(pAd) && pAd->RfIcType == RFIC_3020) ||
			(IS_RT3090(pAd) && pAd->RfIcType == RFIC_3020))
	{
		if (Ant == 0)
		{
			/*
				Main antenna
				E2PROM_CSR only in PCI bus Reg., USB Bus need MCU commad to control the EESK pin.
			*/
#ifdef RTMP_MAC_USB
			AsicSendCommandToMcu(pAd, 0x73, 0xFF, 0x1, 0x0);
#endif /* RTMP_MAC_USB */

			RTMP_IO_READ32(pAd, GPIO_CTRL_CFG, &Value);
			Value &= ~(0x0808);
			RTMP_IO_WRITE32(pAd, GPIO_CTRL_CFG, Value);
			DBGPRINT(RT_DEBUG_TRACE, ("AsicSetRxAnt, switch to main antenna\n"));
		}
		else
		{
			/*
				Aux antenna
			 	E2PROM_CSR only in PCI bus Reg., USB Bus need MCU commad to control the EESK pin.
			*/
#ifdef RTMP_MAC_USB
			AsicSendCommandToMcu(pAd, 0x73, 0xFF, 0x0, 0x0);
#endif /* RTMP_MAC_USB */
			RTMP_IO_READ32(pAd, GPIO_CTRL_CFG, &Value);
			Value &= ~(0x0808);
			Value |= 0x08;
			RTMP_IO_WRITE32(pAd, GPIO_CTRL_CFG, Value);
			DBGPRINT(RT_DEBUG_TRACE, ("AsicSetRxAnt, switch to aux antenna\n"));
		}
	}
}
開發者ID:Audioniek，項目名稱:Fortis-4G，代碼行數:58，代碼來源:rt30xx.c

示例2: RTUSBWriteBBPRegister

NTSTATUS	RTUSBWriteBBPRegister(
	IN	PRTMP_ADAPTER	pAd,
	IN	UCHAR			Id,
	IN	UCHAR			Value)

{
	BBP_CSR_CFG_STRUC	BbpCsr;
	int					BusyCnt;
	for (BusyCnt=0; BusyCnt<MAX_BUSY_COUNT; BusyCnt++)
	{
		RTMP_IO_READ32(pAd, H2M_BBP_AGENT, &BbpCsr.word);
		if (BbpCsr.field.Busy == BUSY)
			continue;
		BbpCsr.word = 0;
		BbpCsr.field.fRead = 0;
		BbpCsr.field.BBP_RW_MODE = 1;
		BbpCsr.field.Busy = 1;
		BbpCsr.field.Value = Value;
		BbpCsr.field.RegNum = Id;
		RTMP_IO_WRITE32(pAd, H2M_BBP_AGENT, BbpCsr.word);
		AsicSendCommandToMcu(pAd, 0x80, 0xff, 0x0, 0x0);
		pAd->BbpWriteLatch[Id] = Value;
		break;
	}
	if (BusyCnt == MAX_BUSY_COUNT)
	{
		DBGPRINT_ERR(("BBP write R%d=0x%x fail\n", Id, BbpCsr.word));
		return STATUS_UNSUCCESSFUL;
	}
	return STATUS_SUCCESS;
}
開發者ID:AppEngine，項目名稱:linux-2.6，代碼行數:31，代碼來源:rtusb_io.c

示例3: RT28xxUsbMlmeRadioOn

VOID RT28xxUsbMlmeRadioOn(
	IN PRTMP_ADAPTER pAd)
{
    DBGPRINT(RT_DEBUG_TRACE,("RT28xxUsbMlmeRadioOn()\n"));

	if (!RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_RADIO_OFF))
		return;

#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
	{
    	AsicSendCommandToMcu(pAd, 0x31, 0xff, 0x00, 0x00);
		RTMPusecDelay(10000);
	}
#endif // CONFIG_STA_SUPPORT //
	NICResetFromError(pAd);

	// Enable Tx/Rx
	RTMPEnableRxTx(pAd);

	// Clear Radio off flag
	RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_RADIO_OFF);

#ifdef CONFIG_STA_SUPPORT
	IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
		RTUSBBulkReceive(pAd);
#endif // CONFIG_STA_SUPPORT //

	// Set LED
	RTMPSetLED(pAd, LED_RADIO_ON);
}
開發者ID:458941968，項目名稱:mini2440-kernel-2.6.29，代碼行數:31，代碼來源:cmm_data_2870.c

示例4: RTUSBFirmwareWrite

/*
	========================================================================

	Routine Description: Write Firmware to NIC.

	Arguments:

	Return Value:

	IRQL =

	Note:

	========================================================================
*/
NTSTATUS RTUSBFirmwareWrite(
	IN PRTMP_ADAPTER pAd,
	IN PUCHAR		pFwImage,
	IN ULONG		FwLen)
{
	UINT32		MacReg;
	NTSTATUS 	Status;
//	ULONG 		i;
	USHORT		writeLen;

	Status = RTUSBReadMACRegister(pAd, MAC_CSR0, &MacReg);


	writeLen = FwLen;
	RTUSBMultiWrite(pAd, FIRMWARE_IMAGE_BASE, pFwImage, writeLen);

	Status = RTUSBWriteMACRegister(pAd, 0x7014, 0xffffffff);
	Status = RTUSBWriteMACRegister(pAd, 0x701c, 0xffffffff);
	Status = RTUSBFirmwareRun(pAd);

#ifdef RT30xx
	RTMPusecDelay(10000);
	RTUSBWriteMACRegister(pAd,H2M_MAILBOX_CSR,0);
	AsicSendCommandToMcu(pAd, 0x72, 0x00, 0x00, 0x00);//reset rf by MCU supported by new firmware
#endif

	return Status;
}
開發者ID:AppEngine，項目名稱:linux-2.6，代碼行數:43，代碼來源:rtusb_io.c

示例5: RT28xxUsbStaAsicForceWakeup

VOID RT28xxUsbStaAsicForceWakeup(
	IN PRTMP_ADAPTER pAd,
	IN BOOLEAN       bFromTx)
{
	BOOLEAN	Canceled;

	if (pAd->Mlme.AutoWakeupTimerRunning)
	{
		if ( !OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_DOZE) )
		{
			return;	
		}
		RTMPCancelTimer(&pAd->Mlme.AutoWakeupTimer, &Canceled);
		pAd->Mlme.AutoWakeupTimerRunning = FALSE;
	}

#ifdef MT7601
	if ( IS_MT7601(pAd) )
	{
		ASIC_RADIO_ON(pAd, DOT11_RADIO_ON);
	}
	else
#endif /* MT7601 */
	{
		AsicSendCommandToMcu(pAd, 0x31, 0xff, 0x00, 0x02, FALSE);
	}

	OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_DOZE);
}
開發者ID:adriano65，項目名稱:n300-pda，代碼行數:29，代碼來源:cmm_data_usb.c

示例6: RTMPSetSignalLED

/*
	========================================================================
	
	Routine Description:
		Set LED Signal Stregth 

	Arguments:
		pAd						Pointer to our adapter
		Dbm						Signal Stregth

	Return Value:
		None

	IRQL = PASSIVE_LEVEL
	
	Note:
		Can be run on any IRQL level. 

		According to Microsoft Zero Config Wireless Signal Stregth definition as belows.
		<= -90  No Signal
		<= -81  Very Low
		<= -71  Low
		<= -67  Good
		<= -57  Very Good
		 > -57  Excellent		
	========================================================================
*/
VOID RTMPSetSignalLED(RTMP_ADAPTER *pAd, NDIS_802_11_RSSI Dbm)
{
	UCHAR		nLed = 0;




	if (pAd->LedCntl.MCULedCntl.field.LedMode == LED_MODE_SIGNAL_STREGTH)
	{
		if (Dbm <= -90)
			nLed = 0;
		else if (Dbm <= -81)
			nLed = 1;
		else if (Dbm <= -71)
			nLed = 3;
		else if (Dbm <= -67)
			nLed = 7;
		else if (Dbm <= -57)
			nLed = 15;
		else 
			nLed = 31;

		/* */
		/* Update Signal Stregth to firmware if changed. */
		/* */
		if (pAd->LedCntl.LedIndicatorStrength != nLed)
		{
			AsicSendCommandToMcu(pAd, MCU_SET_LED_GPIO_SIGNAL_CFG, 0xff, nLed, pAd->LedCntl.MCULedCntl.field.Polarity, FALSE);
			pAd->LedCntl.LedIndicatorStrength = nLed;
		}
	}
}
開發者ID:23171580，項目名稱:ralink，代碼行數:59，代碼來源:rt_led.c

示例7: RT28xxUsbStaAsicSleepThenAutoWakeup

VOID RT28xxUsbStaAsicSleepThenAutoWakeup(
	IN PRTMP_ADAPTER pAd, 
	IN USHORT TbttNumToNextWakeUp) 
{


	/* Not going to sleep if in the Count Down Time*/
	if (pAd->CountDowntoPsm > 0)
		return;


	/* we have decided to SLEEP, so at least do it for a BEACON period.*/
	if (TbttNumToNextWakeUp == 0)
		TbttNumToNextWakeUp = 1;

	RTMPSetTimer(&pAd->Mlme.AutoWakeupTimer, AUTO_WAKEUP_TIMEOUT);
	pAd->Mlme.AutoWakeupTimerRunning = TRUE;

	AsicSendCommandToMcu(pAd, 0x30, 0xff, 0xff, 0x02, FALSE);   /* send POWER-SAVE command to MCU. Timeout 40us.*/

	/* cancel bulk-in IRPs prevent blocking CPU enter C3.*/
	if((pAd->PendingRx > 0) && (!RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST)))
	{
		RTUSBCancelPendingBulkInIRP(pAd);
		/* resend bulk-in IRPs to receive beacons after a period of (pAd->CommonCfg.BeaconPeriod - 40) ms*/
		pAd->PendingRx = 0;
	}


	OPSTATUS_SET_FLAG(pAd, fOP_STATUS_DOZE);

}
開發者ID:557i，項目名稱:mt7610u_wifi_sta_v3002_dpo_20130916，代碼行數:32，代碼來源:cmm_data_usb.c

示例8: RTMPInitLEDMode

void RTMPInitLEDMode(IN RTMP_ADAPTER *pAd)
{
	PLED_CONTROL pLedCntl = &pAd->LedCntl;

	if (pLedCntl->MCULedCntl.word == 0xFF)
	{
		pLedCntl->MCULedCntl.word = 0x01;
		pLedCntl->LedAGCfg = 0x5555;
		pLedCntl->LedACTCfg= 0x2221;

#ifdef RTMP_MAC_PCI
		pLedCntl->LedPolarity = 0xA9F8;
#endif /* RTMP_MAC_PCI */
	}
	
	AsicSendCommandToMcu(pAd, MCU_SET_LED_AG_CFG, 0xff, (UCHAR)pLedCntl->LedAGCfg, (UCHAR)(pLedCntl->LedAGCfg >> 8), FALSE);
	AsicSendCommandToMcu(pAd, MCU_SET_LED_ACT_CFG, 0xff, (UCHAR)pLedCntl->LedACTCfg, (UCHAR)(pLedCntl->LedACTCfg >> 8), FALSE);
	AsicSendCommandToMcu(pAd, MCU_SET_LED_POLARITY, 0xff, (UCHAR)pLedCntl->LedPolarity, (UCHAR)(pLedCntl->LedPolarity >> 8), FALSE);
	AsicSendCommandToMcu(pAd, MCU_SET_LED_GPIO_SIGNAL_CFG, 0xff, 0, pLedCntl->MCULedCntl.field.Polarity, FALSE);

	pAd->LedCntl.LedIndicatorStrength = 0xFF;
	RTMPSetSignalLED(pAd, -100);	/* Force signal strength Led to be turned off, before link up */

	RTMPStartLEDMode(pAd);
}
開發者ID:23171580，項目名稱:ralink，代碼行數:25，代碼來源:rt_led.c

示例9: RTMPAdjustFrequencyOffset

/*
    ========================================================================
    Routine Description:
        Adjust frequency offset when do channel switching or frequency calabration.
        
    Arguments:
        pAd         		- Adapter pointer
        pRefFreqOffset	in: referenced Frequency offset   out: adjusted frequency offset
        
    Return Value:
        None
        
    ========================================================================
*/
BOOLEAN RTMPAdjustFrequencyOffset(
	IN PRTMP_ADAPTER    pAd,
	INOUT PUCHAR pRefFreqOffset)
{
	BOOLEAN RetVal = TRUE;
	UCHAR RFValue = 0; 
	UCHAR PreRFValue = 0; 
	UCHAR FreqOffset = 0;
	UCHAR HighCurrentBit = 0;
	
	RTMP_ReadRF(pAd, RF_R17, &FreqOffset, &HighCurrentBit, 0x7F);
	PreRFValue =  HighCurrentBit | FreqOffset;
	FreqOffset = min((*pRefFreqOffset & 0x7F), 0x5F);
	RFValue = HighCurrentBit | FreqOffset;
	if (PreRFValue != RFValue)
	{
#ifdef RTMP_MAC_USB
		RetVal = AsicSendCommandToMcu(pAd, 0x74, 0xff, FreqOffset, PreRFValue, FALSE);
#else
		RetVal = (RT30xxWriteRFRegister(pAd, RF_R17, RFValue) == STATUS_SUCCESS ? TRUE:FALSE);
#endif /* !RTMP_MAC_USB */
	}

	if (RetVal == FALSE)
		DBGPRINT(RT_DEBUG_TRACE, ("%s(): Error in tuning frequency offset !!\n", __FUNCTION__));
	else
		*pRefFreqOffset = FreqOffset;

	return RetVal;

}
開發者ID:32743069，項目名稱:amlogic_common_3050，代碼行數:45，代碼來源:rt_rf.c

示例10: MyRTMPTurnOffLED

RTMP_BUILD_DRV_OPS_FUNCTION_BODY

#endif /* OS_ABL_FUNC_SUPPORT */
#endif /* LINUX */

#ifndef LED_CONTROL_SUPPORT
void MyRTMPTurnOffLED(IN RTMP_ADAPTER *pAd)
{
	LED_CONTROL my_LED_CONTROL;
	PLED_CONTROL pLedCntl = &my_LED_CONTROL;

	//first time after init elways run this scope
	//if (pLedCntl->MCULedCntl.word == 0xFF)
	{
		pLedCntl->MCULedCntl.word = 0x01;
		pLedCntl->LedAGCfg = 0x5555;
		pLedCntl->LedACTCfg= 0x2221;

#ifdef RTMP_MAC_USB
		pLedCntl->LedPolarity = 0x5627; 
#endif /* RTMP_MAC_USB */
	}
	
	AsicSendCommandToMcu(pAd, MCU_SET_LED_AG_CFG, 0xff, (UCHAR)pLedCntl->LedAGCfg, (UCHAR)(pLedCntl->LedAGCfg >> 8), FALSE);
	AsicSendCommandToMcu(pAd, MCU_SET_LED_ACT_CFG, 0xff, (UCHAR)pLedCntl->LedACTCfg, (UCHAR)(pLedCntl->LedACTCfg >> 8), FALSE);
	AsicSendCommandToMcu(pAd, MCU_SET_LED_POLARITY, 0xff, (UCHAR)pLedCntl->LedPolarity, (UCHAR)(pLedCntl->LedPolarity >> 8), FALSE);
	AsicSendCommandToMcu(pAd, MCU_SET_LED_GPIO_SIGNAL_CFG, 0xff, 0, pLedCntl->MCULedCntl.field.Polarity, FALSE);
}
開發者ID:ohyeah521，項目名稱:DPO_RT5572_LinuxSTA_2.6.1.3_20121022_mod，代碼行數:28，代碼來源:rtmp_init_inf.c

示例11: RT30xxSetRxAnt

/*void AsicSetRxAnt( */
void RT30xxSetRxAnt(struct rt_rtmp_adapter *pAd, u8 Ant)
{
	u32 Value;
#ifdef RTMP_MAC_PCI
	u32 x;
#endif

	if ((pAd->EepromAccess) ||
	    (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_RESET_IN_PROGRESS)) ||
	    (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_HALT_IN_PROGRESS)) ||
	    (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_RADIO_OFF)) ||
	    (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST))) {
		return;
	}
	/* the antenna selection is through firmware and MAC register(GPIO3) */
	if (Ant == 0) {
		/* Main antenna */
#ifdef RTMP_MAC_PCI
		RTMP_IO_READ32(pAd, E2PROM_CSR, &x);
		x |= (EESK);
		RTMP_IO_WRITE32(pAd, E2PROM_CSR, x);
#else
		AsicSendCommandToMcu(pAd, 0x73, 0xFF, 0x1, 0x0);
#endif /* RTMP_MAC_PCI // */

		RTMP_IO_READ32(pAd, GPIO_CTRL_CFG, &Value);
		Value &= ~(0x0808);
		RTMP_IO_WRITE32(pAd, GPIO_CTRL_CFG, Value);
		DBGPRINT_RAW(RT_DEBUG_TRACE,
			     ("AsicSetRxAnt, switch to main antenna\n"));
	} else {
		/* Aux antenna */
#ifdef RTMP_MAC_PCI
		RTMP_IO_READ32(pAd, E2PROM_CSR, &x);
		x &= ~(EESK);
		RTMP_IO_WRITE32(pAd, E2PROM_CSR, x);
#else
		AsicSendCommandToMcu(pAd, 0x73, 0xFF, 0x0, 0x0);
#endif /* RTMP_MAC_PCI // */
		RTMP_IO_READ32(pAd, GPIO_CTRL_CFG, &Value);
		Value &= ~(0x0808);
		Value |= 0x08;
		RTMP_IO_WRITE32(pAd, GPIO_CTRL_CFG, Value);
		DBGPRINT_RAW(RT_DEBUG_TRACE,
			     ("AsicSetRxAnt, switch to aux antenna\n"));
	}
}
開發者ID:ANFS，項目名稱:ANFS-kernel，代碼行數:48，代碼來源:rt30xx.c

示例12: AsicSetRxAnt

/*
 Antenna divesity use GPIO3 and EESK pin for control
 Antenna and EEPROM access are both using EESK pin,
 Therefor we should avoid accessing EESK at the same time
 Then restore antenna after EEPROM access
 The original name of this function is AsicSetRxAnt(), now change to 
*/
VOID RT30xxSetRxAnt(
    IN PRTMP_ADAPTER    pAd,
    IN UCHAR            Ant)
{
    UINT32    Value;

    /* the antenna selection is through firmware and MAC register(GPIO3) */
    if (IS_RT3070(pAd) && pAd->RfIcType == RFIC_3020)
//    if (IS_RT2070(pAd) || (IS_RT3070(pAd) && pAd->RfIcType == RFIC_3020) ||
//            (IS_RT3090(pAd) && pAd->RfIcType == RFIC_3020))
    {
        if (Ant == 0)
        {
            /*
                Main antenna
                E2PROM_CSR only in PCI bus Reg., USB Bus need MCU commad to control the EESK pin.
            */
#ifdef RTMP_MAC_USB
            AsicSendCommandToMcu(pAd, 0x73, 0xFF, 0x1, 0x0);
#endif /* RTMP_MAC_USB */

            RTMP_IO_READ32(pAd, GPIO_CTRL_CFG, &Value);
            Value &= ~(0x0808);
            RTMP_IO_WRITE32(pAd, GPIO_CTRL_CFG, Value);
            DBGPRINT(RT_DEBUG_TRACE, "AsicSetRxAnt, switch to main antenna\n");
        }
        else
        {
            /*
                Aux antenna
                 E2PROM_CSR only in PCI bus Reg., USB Bus need MCU commad to control the EESK pin.
            */
#ifdef RTMP_MAC_USB
            AsicSendCommandToMcu(pAd, 0x73, 0xFF, 0x0, 0x0);
#endif /* RTMP_MAC_USB */
            RTMP_IO_READ32(pAd, GPIO_CTRL_CFG, &Value);
            Value &= ~(0x0808);
            Value |= 0x08;
            RTMP_IO_WRITE32(pAd, GPIO_CTRL_CFG, Value);
            DBGPRINT(RT_DEBUG_TRACE, "AsicSetRxAnt, switch to aux antenna\n");
        }
    }
    else{
        DBGPRINT(RT_DEBUG_ERROR, "RfIcType(%d) is unknow!!\n", pAd->RfIcType);
    }
}
開發者ID:gexueyuan，項目名稱:Cygnoides，代碼行數:53，代碼來源:rt30xx.c

示例13: RadarDetectionStop

/*
	========================================================================

	Routine Description:
		Radar detection routine

	Arguments:
		pAd 	Pointer to our adapter

	Return Value:
		TRUE	Found radar signal
		FALSE	Not found radar signal

	========================================================================
*/
VOID RadarDetectionStop(
	IN PRTMP_ADAPTER	pAd)
{
	DBGPRINT(RT_DEBUG_TRACE,("RadarDetectionStop.\n"));
	AsicSendCommandToMcu(pAd, 0x60, 0xff, 0x00, 0x00);	/* send start-RD with CTS protection command to MCU*/

	return;
}
開發者ID:Brainiarc7，項目名稱:ralink_sdk，代碼行數:23，代碼來源:dfs.c

示例14: RT33xxSetRxAnt

VOID RT33xxSetRxAnt(
	IN PRTMP_ADAPTER	pAd,
	IN UCHAR			Ant)
{
	UINT32	Value;
	UINT32	x;

	if ((!pAd->NicConfig2.field.AntDiversity) ||
		(RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_RESET_IN_PROGRESS))	||
		(RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_HALT_IN_PROGRESS))	||
		(RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_RADIO_OFF)) ||
		(RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST)))
	{
		return;
	}

	// the antenna selection is through firmware and MAC register(GPIO3)
	if (Ant == 0)
	{
		// Main antenna
		// E2PROM_CSR only in PCI bus Reg., USB Bus need MCU commad to control the EESK pin.
#ifdef RTMP_MAC_USB
		AsicSendCommandToMcu(pAd, 0x73, 0xff, 0x1, 0x0);
#endif // RTMP_MAC_USB //

		RTMP_IO_READ32(pAd, GPIO_CTRL_CFG, &Value);
		Value &= ~(0x0808);
		RTMP_IO_WRITE32(pAd, GPIO_CTRL_CFG, Value);
		DBGPRINT_RAW(RT_DEBUG_TRACE, ("AsicSetRxAnt, switch to main antenna\n"));
	}
	else
	{
		// Aux antenna
		// E2PROM_CSR only in PCI bus Reg., USB Bus need MCU commad to control the EESK pin.
#ifdef RTMP_MAC_USB
		AsicSendCommandToMcu(pAd, 0x73, 0xff, 0x0, 0x0);
#endif // RTMP_MAC_USB //
		RTMP_IO_READ32(pAd, GPIO_CTRL_CFG, &Value);
		Value &= ~(0x0808);
		Value |= 0x08;
		RTMP_IO_WRITE32(pAd, GPIO_CTRL_CFG, Value);
		DBGPRINT_RAW(RT_DEBUG_TRACE, ("AsicSetRxAnt, switch to aux antenna\n"));
	}
}
開發者ID:Erni88，項目名稱:froyo-wm8505-utils，代碼行數:44，代碼來源:rt33xx.c

示例15: RT28xxUsbStaAsicForceWakeup

void RT28xxUsbStaAsicForceWakeup(struct rt_rtmp_adapter *pAd, IN BOOLEAN bFromTx)
{
	BOOLEAN Canceled;

	if (pAd->Mlme.AutoWakeupTimerRunning)
		RTMPCancelTimer(&pAd->Mlme.AutoWakeupTimer, &Canceled);

	AsicSendCommandToMcu(pAd, 0x31, 0xff, 0x00, 0x02);

	OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_DOZE);
}
開發者ID:AbheekG，項目名稱:XIA-for-Linux，代碼行數:11，代碼來源:cmm_data_usb.c


注：本文中的AsicSendCommandToMcu函數示例由純淨天空整理自Github/MSDocs等開源代碼及文檔管理平台，相關代碼片段篩選自各路編程大神貢獻的開源項目，源碼版權歸原作者所有，傳播和使用請參考對應項目的License；未經允許，請勿轉載。